PLASMA CLOUD PAX1800 802.11ax Dual-Band Indoor/Outdoor Access Point User Guide
- June 6, 2024
- PLASMA CLOUD
Table of Contents
PAX1800
Quick Start Guide
INTRODUCTION
Thank you for purchasing the PAX1800. a WiFi 6 AR This Quick Start Guide is designed to guide you through the installation process.
PACKAGE CONTENTS
- Access Point
- Mounting options (ceiling, wall, pole. trail)
- The closed cable housing lid
- Screws and screw plugs for various surfaces
- Cable ties
https://www.plasma.cloud.com/product-detail/pax1800/
CLOUD MANAGEMENT
- Sign up at console.plasma-cloud.com.
- Create your first organization by navigating to Organisations -> Create a new organization. Fill in the form and click Create.
- You can now create your first network. Navigate to Networks -) Create a new network, fill in the form and click Create.
- Setup your network by navigating to Settings -) Network.
- Create and configure your first SSID by navigating to Settings -) SSIDs -) Create a new SSID.
- Go back to Overview and click on the map to add your first Access Point.
The last point can be repeated to add as many Access Points as needed.
You can now plug in your Access Point and connect it to the Internet. The Plasma Cloud configuration only takes a few seconds!
PHYSICAL INSTALLATION
This Access Point is designed to be installed virtually anywhere and can
operate between 0°C – 40°C (32°F 104°F). It comes with a set of mounting
options that can be used to install this device on various surfaces such as
ceilings. walls. poles and T-rails of various sizes.
This Access Point can be powered by:
1. a 12V/2A DC power adapter’
2. a 48-54V/0.5A PoE injector (802.3at)-
- The output shall comply with the requirement of SE LV of IEC 60950-1 or ES1 of IEC 62368-1 and In compliance with the requirements of the limited power source of IEC 60950.1 and IEC 62368-1. Connect dealer or distributor for standard PS. “All ethernet cables are designed for Intra. buckling connection to other equipment Does not connect these ports directly to communication wiring or another wiring that exits the building where the appliance Is located.
T-RAIL MOUNTING
slide the T-rail mount into the .slot of the Access Point.
look the stationary end of the mount bracket to the T-rail.
(Your Access Point is now safely: lipped to the T-rail.
MOUNTING BRACKET OVERVIEW WALL MOUNTING
WALL MOUNTING
Use the provided screws and screw plugs to fix the mounting plate on the wall.
Slide the Access Point over the mounting plate.
Your Access Point is now safely attached to the wall.
SUPPORT
Feel free to visit https://support.plasma-cloud.com for additional technical
guidance or to contact our support department.
C 2020 Finrna Cloud Ltd. AU Richts re:creed 5/F Vat Chas Buidint. 262 Des
Vocux Road Central. Hancock Konc wwwpbstru.
cloud.corn
The software included t this product contains.racopmEtsted soh…we that is
licensed under CPI. A copy of that kerne. along with the instructor on how to
obtain. aal the source code. is available at
https://www.gnu.org/copvleft/gpl.html
POLE MOUNTING
Slide the cable ties through the mounting plate and fasten them around the pole.
Slide the Access Point over the mounting plate.
Your Access Point is now safely tied to the pole.
FCC COMPLIANCE NOTICE
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device. pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates. uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions. may cause harmful interference to radio
communications. However. there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception. which can be determined by
turning the equipment off and on. the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body.
IC COMPLIANCE NOTICE
IC statement: CAN ICES-003(B)/NMB-003(B) This product meets the applicable
Innovation. Science and Economic Development Canada technical specifications.
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions: (1) This device may not cause
interference: and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
This device complies with the ISED radiation exposure limit set forth for an
uncontrolled environment. This device should be installed and operated with a
minimum distance of 22 cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunct-don with any other antenna or
transmitter.
CE COMPLIANCE NOTICE
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
| BE| BG| CZ| DK| DE| EE| IE
---|---|---|---|---|---|---|---
EL| ES| FR| HR| IT| CY| LV
LT| LU| HU| MT| NL| AT| PL
PT| RO| SI| SK| Fl| SE| UK
The marking information is located at the bottom of the apparatus.
PRIVACY NOTES
For our customer privacy policy. please visit: haps://www.plasma-cloud .comicustomer-policy/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>