ALKOXY WXC-001 Magnetic Fast Wireless Car Charger Instruction Manual
- June 6, 2024
- ALKOXY
Table of Contents
WXC-001 Magnetic Fast Wireless Car Charger
ALKOXY
SAFETYNOTICE
1Donotpullthepowercardhardtoavoidthepowercard frombreakingorfallingoff.
2Donotdisassemblebyyourselforthrowitintofireor
watertoavoidshortcircuitandleakage.
3Donotuseinseverelyhightemperaturehumidityor
corrosiveenvironmentstoavoidleakageofelectricitydue todamagetothecircuit.
METHODOFUSE
1.Placenutaroundheadwithbottomfacingcharger,thenfully
insertballheadintosocket.Tightennuttolockangleinplace.
4.Pushdownlockinglatchontopofbasetosecurebasestosurface.
2.Findsmoothsurfacetoattachchargertothenwipesurface cleanwithwetwipes.
5.Adjustlengthandangleofmount,thenrotateknobsclockwiseto lockinplace.
Magnetic Fast Wireless Car Charger
WXC-001
TECHNICALSPECIFICATIONS
NameMagneticFastWirelessCarCharger Input:5V=3A,9V=2A Output:15w(max)
1.unscrewthenutfromthesocket.
4.A ttackclamptocarvent.
2.Placenutaroundballheadwithtopfacingclamp,thenfullyinsert ballheadintosocket.
5.Magneticallyattachphonetobegincharging.
3.T ightenthenutclockwise.
3.Firmlypressbasetosurface.
6.Pluginchargingpad.attachphonetochargertobegincharging.
7.Torepositionmount.unlocklatchandpeelbaseoffsurface.Wash ba s ew i t hr u n n
i n gwate ra n da l l o wtod r yb e fo rereatta c h i n g .
FREQUENTLYASKEDQUESTIONS
1.Chargingisslow.Themobilephoneitselfortheexternal
receivingcoilallowsthewirelesschargingcurrenttobe
different,ortheapplicationrunningrecommendedto reduceorclosetheapplication.
2.Thephoneischargingintermittently,andtheindicator
lightflashes.Ifthechargingcurrentisnotenough,please
useacharginghead(adapter)withsufficientpower9V/ 1.67AoraboveQC2.0.
3.Chargingfever,Itisnormalfoethereceivingcoilor
transmitterboardtogenerateheatduringwireless
charging.Itisrecommendedtoadjustthecharging position.
4.Thechargerdoesnotwork.Donotputmetaldebrisor
magneticcardsonthechargingarea.Iftheproductdoes
notworkduetooverheating,pleasetakeoffthephone a n dwa i tfo ri ttoco o ld o w
na n dt r yc h a rg i n ga ga i n .
5.Thehostindicatorisnormal,butthemobilephonecannot
work,Themobilephonereceivingcoilisfaultyorthe
chargingpositionisnotaligned.Itisrecommendedto
replacethereceivingcoilorrepairthemobilephone.
6.Theindicatorlightofthehostisnotbright.Ifthehostfails,
contactaftersalesmaintenance.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: — Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. — Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. — Consult the dealer or an experienced radio/TV
technician for help. Radiation Exposure Statement This device complies with
FCC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. During the operation of device a distance of 15
cm surrounding the device and above the top surface of the device must be
respected.