Hangzhou Kaite Electrical Appliance 50023 Mobile Phone Wireless User Manual
- June 6, 2024
- Hangzhou Kaite Electrical Appliance
Table of Contents
Package contents
- Mobile phone wireless
- User manual
Product components introduction
A Charger Port
B Wireless Charger Area
Frequently Asked Questions
- Why the wireless charger cannot charge the phone? The phone is not aligned to the changing area or the receiving coil is not properly installed.
- Why it will be hot when charging? It is normal that the receive coil or the laugh plate fever at wireless charging process.
- Why it turn off and on when charge the device? a. The current is not enough or voltage instability if using the adapter to charge. Please use a qualified adapter. b. Charging poison is too partial to cause the electromagnetic induction is not good. Please adjustable the charing position.
- Why the phone cannot be charge even though that the host light is normal? Mobile phone receiver coil with some defective, It is recommended to update the receiving coil or repair the phone. (Built-in receiver coil)
- Chargeing is slow Moblie phone or external receiver coil allows the charging current is not the same,or the mobile phone’s power will loss at the standby mode. It is recommended to reduce the phone standby program. Or if Adapter does not meet 9V/2A, Please select the reglur adapter .(Other questions please contact the customer service directly)
Customer Support
This product warranty period of 12 months,life-long customer service support.
How to use
Connect the wireless charger to adapter Put the mobile phone on the charging plate and the battery starts to charge If mobile phone doesn’t start to charge, please try to reposition it.
Product features
Produktname|
---|---
Entladungsverlust| 60-500mW
Input voltage| 5V/2A,9V2A (QC2.0 charger)
Output voltage| 5-9V
10W maximum efficiency| 80%
Output current| 1.1A
Output power| 10W
SIZE|
Charging distance| ≤8mm
The use of high afficiency programs and imported chips, stable performance. Dual-launch coil, no blind spot charging, the phone can be horizontal and vertical placement. Charging bracket can be adjusted ed angle. Imported ABS material, fine matte pattern, highlight the high-end elegance.
Attention
- Please use a qualified QC2.0 power adapter, otherwise, it may cause the charge to be unstable.
- Do not put metal debris or the magnetic card on the charging board, may cause damage to the charger or abnormal.
- The use of the process if the receiving coil or the launch plate overheating lead to stop charging, please remove the charging device, to be cooled, try to recharge.
Safety instructions
Do not squeeze and crash
Do not pull the power cord hard enough to avoid breaking or falling off the
power cord
Do not disassemble or put the wireless charger into fire.
Do not use the wireless charging in severe high temperatures, humid or
corrosive environment,to avoid damage to the circuit leakage phenomenon.
Specifications
| Woking frequency | 115-205KHz |
|---|---|
| Protocol standards | WPC1.2.1 |
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>