Empava 30 in. 400 CFM Ducted Kitchen Wall Mount Range Hood User Manual

: June 6, 2024
: Empava

Table of Contents

TECHNICAL CHARACTERISTICS
MAIN PARTS NAME
INSTALLATION REQUIREMENT
INSTALLATION PROCEDURES
OPERATING INSTRUCTION
MAINTENANCE
TO REPLACE LIGHT
IMPORTANT SAFETY INSTRUCTIONS:
TROUBLESHOOTING
Documents / Resources

RANGE HOOD

Installation and Operation
Manual

Dear consumer,
Thanks for your purchase of our range hood and we hope we can fully satisfy all of your needs. Please read the entire instructions carefully before proceeding to obtain the best results of operating the range hood.

TECHNICAL CHARACTERISTICS

Model No.: EMPV-30RH05 EMPV-30RH06
Total power: 204W
Motor power: 200W
Led Light: 2x2W
Voltage: 120V
Frequency: 60Hz
Filter: Steel Baffle filter
Control: Touch Control
Please note that this product is marked with the symbol: According to the Waste of Electrical Electron Equipment (WEEE) directive, WEEE should be separately collected and treated. If at any time in the future you need to dispose of this product, please do NOT dispose of this product with household waste. Please send this product to WEEE collecting points where available.

MAIN PARTS NAME

INSTALLATION REQUIREMENT

Do not install the range hood where there are many doors to windows in order to avoid eﬀecting the exhaust eﬃciency of the hood that is caused by air convection. (ﬁg.1)
Install the range hood right above the cooking surface. The recommended distance between the cooking surface and the lower edge of the range hood is a minimum of 27.56″ to a maximum of 31.5″. (Fig.2)
In order to get the best performance, do not extend the vent pipe too long, and try to make the bend of the vent pipeless
and straight, make sure the vent pipe connection is ﬁrm and airproof. (Fig.3)
After hanging the range hood on the wall, make sure the hood is level and vertical. (Fig.4)
The air Outlet is not allowed to connect to chimney ﬂues or combustion gas ducts. The air outlet should under no circumstances be connected to ventilation ducts for a room in which fuel-burning appliances are installed.

INSTALLATION PROCEDURES

SAFETY WARNING
THE HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING, OR SERVICING.

Step 1:
Put the vent pipe to the air outlet like this picture. And use one ST3.9×10 screw to fix the vent pipe.

Step 2:
Match the hook to the holes of the inner duct cover and fix it well with M4 screws.

Step 3:
Insert the inner duct cover into the outer duct cover.

Step 4:
Matching the holes of the outer duct cover and blower box, fix the outer duct cover to the blower box using 8pcs M4*10 screw provided with the fixing tool as the direction of the illustrated.

Step5:
According to the size of hook key holes. 10mm in diameter and 75~85mm in depth. Press the 3 expanding tube provided into the holes. Fix the hook using the 5×50 metal screw provided. Then insert three M5X50 screws to A and B And C holes to fix the hook on the wall Drill 3 holes in level in the wall with steadily.

Step 6:
Hang the entire hood onto the hook, ensure the hood is level and vertical.

Step 7:

Draw the inner duct cover up to the suitable height, mark on the wall two keyholes of the outer duct cover bracket with pen.
Put down the inner duct cover gently, drill the keyholes in 75-85 mm depth on the horizontal level using a 10mm drill.
Press the expanding tube provided into the holes.
Matching the inner duct cover with the holes, tighten the inner duct cover with two 5×50 metal screws provided.

Step 8:
Extend the air outlet of the exhaust pipe out-of-door. Try to make the bend of the exhaust pipe is no more than 120°.

OPERATING INSTRUCTION

1). Electronic Switch

1. How to use the Touch Control

| Press to turn on /off the light.
---|---
Press to select the high speed.
Press to select the medium speed.
Press to select the low speed.
Press to select on/off.

2). Touch Control
A. Light
B. Time
C. Speed down
D. Speed up
E. Max speed
F. On /off

A: Light
Press the button once to turn on the light, press again to turn off.
B. Timer
In standby mode, press 3 seconds, to enter into time setting mode, Press “+” set hour (0-23 circle set) and press “–” set minute(0-59),
No operation within 5 seconds for automatic confirmation. When working, press once to enter into delay turn-off mode for 3 minutes.
Press again to increase delay turn-off time from 3-59 minutes.
No operation for 5 seconds, the hood will be turned off in 3 minutes.
Press again to turn off immediately.
C.- In standby mode, press to change to speed 1.
D.+ In standby mode, press to change to speeds 2 & 3.
E. Speeds
In standby mode, press once to start high speed.
F. Power on/off
In standby mode, press once to turn on all buttons. Press again to turn off the power. When working, press once to start delay turn off 3 minutes. In delay turn-off mode, press again to stop delay turn-off.

MAINTENANCE

CAUTION : NEVER PUT YOUR HAND INTO THE AREA HOUSING WHILE THE FAN IS OPERATING.
FOR THE OPTIMAL LEVEL FO OPERATION, CLEAN THE RANGE HOOD SURFACE, AN AND ALUMINUM FILTER REGULARLY.

Use only mild soap or detergent solutions to clean the range hood surface. Dry surfaces using a soft cloth.
Using a stainless steel cleaner to bring the glow back into a stainless ﬁnish.
Clean the ﬁlter once a week or according to use status. Press the buckle of the ﬁlter slightly, take oﬀ the ﬁlter and put it into warm soapy water using mild detergent, wipe the ﬁlter with soft brush. Replace the ﬁlter after it’s dry.
Clean the motor fan and other inside parts once a half-year or according to use status by QUALIFIED PERSON.
DO NOT clean the motor with water or other liquid.

TO REPLACE LIGHT

To replace Led light (Pic.1)
Сaution: LED light can not replace a new bulb, just replace a new LED light assembly.
Make sure all the control switches are oﬀ, and the range hood is unplugged! Please follow below instructions:

Take out the ﬁlters, and cut oﬀ the wire connection of the light.
Press the spring according to the arrow direction, then you can take oﬀ the LED light.
You can replace a new LED assembly no more than rating.
Then put the light assembly to the hood in the reverse direction. Connect the wire of the lamp.
Fit on the ﬁlters.

IMPORTANT SAFETY INSTRUCTIONS:

WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when ﬂambeing food (i.e.Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).
c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁlter.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the ﬂames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN – You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d) Use an extinguisher ONLY if:

You know you have a Class ABC extinguisher, and you already know how to operate it.
The ﬁre is small and contained in the area where it started.
The ﬁre department is being called.
You can ﬁght the ﬁre with your back to an exit.
WARNING : TO PROVIDE PROTECTION AGAINST ELECTRIC SHOCK, CONNECT TO PROPERLY GROUNDED OUTLETS ONLY.
WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device. AVERTISSEMENT : NE CONVIENT PAS A DES REGULATEURS DE VITESSE A SEMI-CONDUCTEURS.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This
appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING – Improper grounding can result in a risk of electric shock.
Consult a qualiﬁed electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualiﬁed electrician install an outlet near the appliance
WARNING – TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

TROUBLESHOOTING

CAUTION : Disconnect the power supply before servicing.

Status	Cause and Method of Repairing	Tools required
No power	Check circuit breakers
If the power supply is damaged, please call for a qualified person	Philips

Screwdriver
The motor does not run| a). The motor is broken, replace the motor.
b). The switch control is broken, replace switch
c). The capacitor is broken, replace the capacitor.| Philips Screwdriver
Body vibration| a). The installation is not correct, check it and make sure the hood is level.
b). The fan is broken, replace motor assembly.
c). The fan motor was not properly installed, check and make sure it is firmly installed.| Philips Screwdriver
Noise vibration| Something dropped into the blower, check and clean blower.| Philips Screwdriver
Weak suction| a).The distance from the range hood to the cooking surface is too far, make sure the distance between the bottom of the hood to the cooking surface is a minimum 24″ to a maximum 27″.
b). Windows, doors, and drafts can affect the performance of the range hood.
c). There are other air conditions affecting the vent pipe, make sure the lower vent pipe’s exit is in a downward direction.
d). The running rate of the motor slows down. replace the motor or capacitor.
If the range hood is near the window,
the best solution is to protect the back of the range hood from the draft caused by a window or door.| Philips Screwdriver
Light does not work| Replace the LED lamp.| Philips Screwdriver

EMPAVA APPLIANCE INC.
Add: 15253 Don Julian Rd, City of Industry, CA 91745
Tel:888-682-8882
www.empava.com