GE current WWD2-2SM Daintree Networked Wireless Wall Dimmer Installation Guide
- June 6, 2024
- GE current
Table of Contents
WWD2-2SM Daintree Networked
Wireless Wall Dimmer
Installation Guide
BEFORE YOU BEGIN
Read these instructions completely and carefully. Save these instructions for
future use.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
- Disconnect power before service installation, or maintenance of the product.
RISK OF FIRE
- Follow all relevant IEC or UL instructions and local building codes.
RISK OF INJURY
- Wear safety glasses and gloves during installation and servicing.
FCC / IC COMPLIANCE STATEMENTS
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT
To ensure the product warranty is valid, please ensure all installation
instructions and environmental conditions for storage and operation are
complied with.
Installation to be performed by factory-trained or qualified personnel.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
Installation
|
---|---
1. Use a standard screwdriver to open the faceplate, Pull the plastic
insulation strip out of the battery compartment.| 2. If you want to install
it on the junction box, use the screw in the package and a cross screwdriver
to lock the device on the junction box
|
3. Install the faceplate onto the device.
Note: The device supports the use of other standard faceplates on the market.|
4. If you want to install the device on the wall, use the 3M tape in the
package to stick the device firmly on the wall.
You can also hand-held use the device in the CSM signal cover area.
Network Reset
To reset the network of the device, remove the faceplate from the device. Then
press and hold the reset button for 5 seconds. Install the faceplate back onto
the device.
Press either the dimming up or down button to enter the pairing mode to join
the device to a network.
Battery Replacement
|
---|---
1. The device’s LED flashing every 30 seconds indicates that the batteries
need to be replaced.| 2. Use a standard screwdriver to open the faceplate.
|
3. Separate the battery cover from the device. Replace the batteries with
AAA batteries. All batteries need to be replaced at the same time.| 4.
Install the faceplate onto the device.
Product Dimensions
Technical Data
Product Specifications
| Dimensions | 114mm H x 70mm W x 15mm D |
|---|---|
| Weight | 130g |
| Power Supply | (4) AAA1.5V battery |
| battery life | 5yr (normal operation) |
| Operating Environment | -10°C to 40°C （Indoor Use Only) |
| Status indicator | Network joined/Button triggered |
| Mounting | Surface-mounted, screw hole in the backplate, the cover could be |
removed, handheld
Warranty| 5 years
Product Availablity
| SKU | DESCRIPTION | ARTICLE-NO. |
|---|---|---|
| 93141315 | Daintree® Networked Wireless Wall Dimmer | WWD2-2SM |
Product Certifications
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Model No: WWD2-2SM
Product Name: Wireless Wall Dimmer
Suppliers Name: Current Lighting Solutions, LLC
Suppliers Address (USA): 1975 Noble Road, East Cleveland, OH 44112
Suppliers phone number and / or internet contact information:
1-866-855-8629
www.gecurrent.com
© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE
monogram are trademarks of the General Electric Company and are used under
license. Information provided is subject to change without notice. All values
are design or typical values when measured under laboratory conditions.
CTRL027 (Rev 07/05/20) Enovia – A-1025984
Documents / Resources
| GE
current WWD2-2SM Daintree Networked Wireless Wall
Dimmer
[pdf] Installation Guide
WWD2SM, 2AS3F-WWD2SM, 2AS3FWWD2SM, WWD2-2SM, Daintree Networked Wireless Wall
Dimmer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>