Mitoba Design ECM211127-V02-000FA040 Wireless Remote Control Touch Mirror Instructions
- June 6, 2024
- Mitoba Design
Table of Contents
SHEN ZHEN ELITE CHIP MICROCUIT CO.,LTD
ECM211127-V02-000FA040 Wireless Remote Control Touch Mirror
1. Picture of Product
2. Technical Parameter
Model: Regent Micro ECM211127-V02-000FA040
Input voltage: DC 12V
Working current: 5A (max)
Load power: ≤50W
Sensing principle: capacitive touch sensing + wireless remote control
Sensing distance: 4-5mm (glass medium) + 2mm (acrylic backlight)
Remote control distance: The remote control distance in an open and
unobstructed space is about 20 meters.
Dimming function: support stepless dimming and three-color switching function
Outlet length: can be customized, default 200mm
Product size: motherboard: 57.5mm109mm7mm (LWH), remote control board:
60mm61mm7mm (LWH)
3. Control method
Three-button control mode:
- Middle touch: short press the switch and long press the stepless dimming function.
- Left touch: Switch colors. Right touch: short press the switch to prevent fog.
- Indicator light: When the power is turned on, the main light is off, and the main light is off, and the main light is on. The anti-fog on indicator is on white, and the anti-fog off indicator is off (color can be customized).
4. Instructions
Each time the power is turned on within 8 seconds is the time to learn the
code pairing. Press the remote control button and the load light flashes once
to indicate that the code pairing is successful. Press the remote again to
turn the lights on and off. The touch cannot be operated within 8 seconds of
power-on, otherwise the operation will be invalid for code matching. After 8
seconds of power-on, the learning function will end and the code will be
invalid.
Clear code pairing: The code pairing time is cleared within 5 seconds each
time the power is turned on. Press and hold the touch switch key for 5
seconds, and the touch indicator light turns off 3 times to clear the code
value successfully. Pressing the remote again has no effect. The touch cannot
be operated within 5 seconds of power-on, and the operation will be invalid
after clearing the code, and the clearing of the code after 5 seconds of
power-on will be invalid.
The remote control can be paired with the mirror one-to-one, and it can also
control multiple mirrors and multiple remote controls at the same time to
control one mirror. The memory can be cleared, and no mirrors can be remotely
controlled after the memory is cleared. There is a power-off memory. After the
code is successfully matched, power off and then power on again, and you can
directly control the code without re-matching the code.
(1) Middle touch key: In standby state, short press the white LED light
on, then short press the white LED light off. Long press to enter the stepless
dimming state, and the brightness gradually increases or decreases.
(2) Left touch key: This key is valid only after the middle touch key is
turned on. Short press the white LED light on, then short press the warm LED
light on, short press the white LED light + warm LED light on, short press
again to return to the white LED light on, cycle in turn. Right touch key:
short press to switch the anti-fog function. Short press to turn on the anti-
fog, short press again to turn off the anti-fog, and cycle in turn.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
www.szecm.com 0755-29100085 szecm@163.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>