SpotSee LOGIC 360 Data Logger Instruction Manual

: June 6, 2024
: SpotSee

Table of Contents

Getting Started
Using A Pre-Configured LED-Logger
Connecting to the Device & Retrieving Data
Documents / Resources

LOG•IC® 360 Data Logger Manual

USER MANUAL

Getting Started

SYSTEM REQUIREMENTS & SOFTWARE LOG-IC PDF LOGGER Windows or Mac-based operating systems
I-PLUG MANAGER Windows-based operating systems only
LOG-IC PDF Loggers are powered by Switrace I-Plug Technology. The Switrace I-Plug Manager is a free tool that allows you to configure or modify the logger settings.

Configure, Re-Configure (Multi-Use), or Modify Your Logger Settings
Once your LOG-IC PDF logger is active, do not plug it into a USB port unless you want to stop the logger.

Download the FREE I-Plug Manager software by visiting https://switrace.com/download/
Plug the LOG-IC data logger into any USB port
Configure or modify an unused Single-use or any Multi-use PDF logger. You can adjust these settings:
a. Sample Time
b. Measures
c. Celsius or Fahrenheit
d. Start Delay
e. Alarms
Select Save Settings

Using A Pre-Configured LED-Logger

Starting & Stopping the Logger
Starting the Logger
When you are ready to begin recording temperature with your logger:

Press and hold the START button until all 4 LED’s flash, releasing when the GREEN LED is active
The GREEN LED will then begin flashing, verifying the logger is active or in Start Delay.

Stopping the Logger
LOG-IC PDF loggers are programmed with a typical or customized trip duration and will continue to record until the end of that duration.
There are 2 different ways to stop the device before the end of a trip duration:

Press and hold the STOP button for 6 seconds until all 4 LED’s flash, releasing when the RED LED is active and fixed.
Plug the device into a USB port of a computer.

Reading the Logger
If you press the START button at any time, LED indicators give valuable information about your temperature data:
Led Indicators:

Ready State | 4 Blinking LED Indicators
Device has not been started.
NOTE: When the device is in this state, only the start button is active.
Running State | Blinking Green
This confirms that the device is in Start Delay or actively logging.
NOTE: There is a fixed green LED indicator during the first 2 minutes of recording.
Stopped State | Fixed Red
This confirms that the device is no longer actively logging
Low Alarm Triggeered
Blinking Blue | In the Running or Stopped State, a blinking blue indicator identifies a low alarm has been triggered.
Fixed Blue | In the Running or Stopped State, a fixed blue indicator shows an ultra-low alarm has been triggered.
High Alarm Triggeered
Blinking Orange | In the Running or Stopped State, a blinking orange indicator identifies a high alarm has been triggered.
Fixed Orange | In the Running or Stopped State, a fixed orange indicator identifies an ultra-high alarm has been triggered.

Connecting to the Device & Retrieving Data

Upon plugging into any USB port, the LOG-IC PDF logger will be detected as a USB drive and will be recognized without any additional software.
Do not plug in the logger unless you are ready to stop the device.
There are 2 possible situations when plugging in your device:

If the device was not previously logging, press the START button for the computer to detect.
If the device is active or was previously stopped, the computer will automatically detect the logger and begin to generate the PDF report. Do not remove the logger during the download.

Once the report is ready a new USB Drive will appear on your PC, allowing you to download the PDF report. Based on the configuration of your logger, it could take up to 45 seconds for the PDF report be generated.

Reading the Temperature Data
A detailed graph will be provided once the temperature data is downloaded. Temperature information will be displayed in red and temperature readings will appear on the left side of the screen.

Reading the Temperature and Humidity Data
A detailed graph will be provided once the temperature and humidity data are downloaded. Temperature information will be displayed in red and temperature reading will appear on the left side of the screen. Humidity will be displayed in blue and humidity readings will appear on the left side of the screen.

Rev: 12/2020

Documents / Resources

| SpotSee LOGIC 360 Data Logger [pdf] Instruction Manual
Pharmaceutical Shipping Temperature and Condition Monitors, LOGIC 360 Data Logger, LOGIC 360, Data Logger
---|---