VSEVEN HB605M Wireless Mono Headset User Guide
- June 6, 2024
- VSEVEN
Table of Contents
HB605M
WIRELESS MONO HEADSET
USER GUIDE
In the Box
Overview
How to Wear
-
Insert the detachable Boom Microphone into the 2.5mm receptacle located on the headset.
-
The boom microphone can move to accommodate a user’s preference for right side or left side wear.
-
Position the microphone to your preference.
Operation
Power On
Slide the switch to the CENTER position
Power Off
Slide the switch to the position
Connecting to a PC
PC (W/V7’s Bluetooth Dongle)
The V7 USB dongle and headset are pre-paired and ready for use. Plugin the USB
dongle and power on the headset to enjoy voice and audio performance range of
up to 30 meters (100’) line-of sight. If using the PC’s integrated Bluetooth,
your range may be limited to 10 meters (33’) and you may need to select ‘V7
HB605M’ for the audio playback device in the operating system’s settings.
Connecting
How to connect with the first Bluetooth device.
Slide the power switch to the “CENTER” position. the LED will flash red and
blue when ready to connect.
Windows 10 PCs and Macs will automatically recognize and install drivers.
Connecting to the second Bluetooth device.
Slide the power switch to the “ “ position and hold until ‘pairing’ heard or
the pairing LED flashes, then select “V7 HB605M”
Activate “Bluetooth” in your device‘s settings and select ”V7 HB605M”.
the LED will flash blue to indicate the headphone is connected, and
‘connected’ is heard.
Calls with a Smartphone
Calls with a Smartphone
Siri/Cortana/Assistance
Charging the Headset
During charging the red LED will light. When fully charged, the LED will turn
off. The headset remains on during charging.
To power off, the headset’s power switch must be slid to the off position.
Using the charging stand
Plug the optional charging stand into a powered USB port on your PC, docking station, or USB wall charger, and then dock the headset. It takes approximately 3 hours to fully charge the headset.
Other Operations
Muting the Boom Mic: Depress and hold the button for 2 seconds.
Muting the internal Mic: (When boom mic is not inuse) Depress and hold the key 2 seconds.
Battery Status: After the headset is powered on, press the call button briefly to hear the current battery status 100% -75%-50%-25%.
Clearing the pairing: While the headset is powered on, press and hold the previous and next track buttons simultaneously for 10 seconds. A pink LED will light for 2 seconds and the headset will then enter pairing mode.
Product Specifications
Bluetooth version: Bluetooth V5.0
Bluetooth Profile: A2DPv1.3.1; AVRCPv1.6; HFPv1.7; HSPv1.2; SPP v1.2; DID
v1.3; HID v1.1; PXP v1.0.1; FMP v1.0; BAS v1.0
Working Frequency: 2.402GHz-2.480GHz
Frequency Response: 99±3dB
Receiving sensitivity: >-89dBm
Battery type: Lithium polymer
Mic type and sensitivity: Virtual Microphone -42±3dB
Headphone Driver Size: 30mm
Battery capacity: 410mAh DC
Input: 5V_500MA
FCC ID: 2AKI8-20BF01
Charging voltage: 5V/2A
Bluetooth working range: Up to 30m
Talk time: Up to 18 hours
Charging time: Approximately 3 hours
Standby time: Approximately 175 hours
Compatibility: Windows 10, mac OS, iOS and Android
WARNING
Headsets can deliver sounds at loud volumes and high-pitched tones. Avoid prolonged use of the headset at excessive sound pressure levels. Please read the safety guidelines below prior to using this headset.
Safety information
Use of a headset will impair your ability to hear other sounds. Use caution
while using your headset when you are engaging in any activity that requires
your full attention. This package contains small parts that may be hazardous
to children and should be kept out of reach from children. Do not attempt: To
dismantle or service the product as this may cause a short circuit or other
malfunction which could result in a fire or electric shock. Avoid exposing
your product to rain, moisture, or other liquids to avoid damage to the
product or injury to you. Keep all products, cords, and cables away from
operating machinery. Avoid use while operating a motor vehicle. Built-in
battery care: Please observe the following if the product contains a battery.
Your product is powered by a rechargeable battery. The full performance of a
new battery is achieved only after two or three complete charge and discharge
cycles. The battery can be charged and discharged hundreds of times but will
eventually wear out. Always try to keep the battery between 15°C and 25°C
(59°F and 77°F). A product with a hot or cold battery may not work
temporarily, even when the battery is fully charged. Battery performance is
particularly limited in temperatures well below freezing.
Battery warning!
CAUTION – The battery used in this product may present a risk of fire or
chemical burn if mistreated. Do not attempt to open the product or replace the
battery. This will void the warranty.
Troubleshooting & Support
Headphones will not power on:
- Be sure the headphones are fully charged
My mobile device is unable to find the Bluetooth headphones
- Confirm the headphones are in pairing mode (blue/red indicator
- Remove “V7 HB605M” from your phone’s Bluetooth device list and try again.
- If the model still does not appear, restart the headset and phone, then try again.
After successfully pairing, the headphones disconnect
- Be sure the battery has adequate power and recharge.
- Headphones must be within 10m of most mobile devices.
- Connections may be affected by obstructions such as walls or other electronic devices. Try moving closer to the device you are connected to.
The sound is distorted when listening to music or there is no sound when receiving or making calls through my PC
- Press Call Answer twice or turn off the headset, remove and reinsert the Bluetooth dongle and turn on the headset.
When answering a call, I cannot hear anything
- Ensure the mobile device is connected to the V7 HB605M headphones and not on phone’s speaker or other audio option.
- Increase the volume on your mobile device.
There is no sound when listening to music
- Increase the volume on your headphones or the mobile device.
- Reestablish the Bluetooth wireless connection between the headphones and your mobile device.
- Check if the audio app has paused or stopped playback.
Headphones will not charge
- Confirm that the charging cable is operational or undamaged.
- Ensure that the USB charging cable is fully seated in the headphones and wall charger ports.
- Confirm that the USB port is outputting power. Some USB ports shut off when the PC is off.
Find support for the V7 HB605M at v7world.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>