KRAKEN Smart Housing Vacuum Detector User Manual

KRAKEN Smart Housing Vacuum Detector

Feature

[ Shutter] Button:

• Turn on the device.
• The photo mode – capture a photo.
• Menu mode – exit menu.
• Video mode – start and stop recording

[ MODE] Button:

• Switch modes: Photo – Video recording – Replay
• Menu Mode – exit to the previous shooting mode.

[MF/AF] Button:

• Toggles between Manual Focus – Auto Focus

[MENU/OK] Button:

• Press and hold to turn off the device.
• Enter menu/setting screen.
• Switch between Image Setting – System Setting
• Up/Down buttons will navigate through menu

[UP] Button:

• Switch between full screen display – split screen display.

[Down] Button:

• Press the button to enter filter mode.
• Enter the new menu in the menu mode.

Overview

Kraken Smart Housing is a versatile housing that will fit many smartphones, regardless of iOS or Android operating system. If your phone fits, it will work! Simply ensure Bluetooth is turned on in your device , connect to the Kraken Smart Housing app and put the phone into the housing! Confirm the housing is protected by using the vacuum sealing system. Enjoy diving!

Open/ Close Weefine Smart Housing

To open:

1.  Push out the safety lock as shown in diagram “a” below.
2.  Turn the Lock Plate clockwise, showed in diagram “b” and “c” below.

To close:
Turn the Lock Plate counterclockwise to its original position.

Warning! Make sure that the safety lock has been returned to the locked position. (Device is securely locked when you hear a “click”)

Package

Installation of the lens holder

As the diagram shows below.

Installing the Batteries

•   Install the AAA battery as shown in diagram “d” below.
•   indicator light solid green – Bluetooth connection successful, full battery power ;
•  indicator light flashes green – Bluetooth NOT connected, full battery power
•  Indicator light solid red – Bluetooth connection successful, low battery power;
•  the indicator light flashes red – Bluetooth NOT connected, low battery power.

Warning! The polarity of the battery must match the polarity of the contacts in the housing – ensure the positive and negative poles of the batteries align with the positive and negative poles of the housing.

Installing your Phone

1.  Ensure Bluetooth is on in your device, and connect to the “Kraken Housing” app. Select ·KRAKEN” on the screen.
2.  Insert your phone in the housing as shown in diagrams “e” and “f” below.
3.  Close housing, twist Safety Lock counterclockwise until a “click” is heard.
   Warning! Many phones automatically adjust the screen brightness. To ensure optimal use of the housing, turn off this setting before inserting your phone in the housing.

3. Using the vacuum system
The built-in vacuum system lets you know if the housing is sealed before diving. This is important to keep your device safe.

•  Turn the exhaust valve knob counter-clockwise to open/unscrew

Warning! Ensure the O-rings do not come into contact with any dirt, sand, hair or dust.

•  Install the exhaust valve pump into the vacuum port as shown in the diagram below and begin to pump.

Warning! Be sure to tighten the exhaust valve knob after pumping.

• The vacuum indicator light will flash red and green as you are pumping. When successfully sealed, the indicator light will turn solid green.
•  Reinsert the exhaust valve knob and turn clockwise to Close. If the indicator light remains green after 30 minutes, you are safe to dive.

Warning! If the indicator is red or red to green cycle, the housing is not sealed, please re-check the vacuum system again. Ensure the indicator is green before diving.

•  To release the vacuum seal, unscrew the exhaust valve knob and press the yellow gasket to the side.

Warning! You must release the vacuum seal before attempting to open the housing. The indicator light will turn red when the housing is safe to open.

Turn-ON/OFF WEEFINE Smart Housing

[Shutter] Button:

• Turns on the device, as shown in diagram “i”

[MENU/OK] Button:

• Press and hold to turn off the device, as shown in diagram “il

General Warnings and Instructions

• Do not take apart the Kraken Smart Housing.
• Do not leave the Kraken Smart Housing exposed to a heat source or store in high temperatures. (e.g., in a locked car parked in the sun)
• Remove the battery if the Kraken Smart Housing

will not be used for long periods of time. (e,g., between dive trips) • To avoid leaks, the 0-rings should be checked to ensure that they are free from any dirt, sand, hair and dust every time before use the Kraken Smart Housing. Use a soft cloth to clean the 0-rings if required. The 0-rings should also be carefully checked for cracks or blemishes. Gently and evenly apply a thin coat of grease to the entire 0-rings regularly to prolong 0-ring life. Be careful not to scratch the 0-rings surface. If cracks or blemishes occur, the rings should be replaced immediately. Do not open the Kraken Smart Housing in the water. Wash the exterior of the Kraken Smart Housing thoroughly with clean fresh water immediately after use. Soaking the housing in fresh water will help to remove salt deposits prior to storage.  Please ensure the housing is dry before opening. Allowing water to come in contact with the internal device may cause damage to the device.  Do not disassemble. modify, remanufacture, puncture or damage the Kraken Smart Housing.

Warranty

Kraken provides a warranty against manufacturer defects for 1 year starting from the date of purchase. Manufacturer defects occurring within 15 days of the date of purchase will result in an exchange of product at the vendor. All ot her manufacturer defect s occurring within 1 year of the date of purchase will be repaired at no cost. Proof of purchase is required for warranty support. The warranty does not cover failures or defects resulting from misuse (e.g., modification, damage), natural disasters, or battery issues, including incorrect battery installation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>