LG PL2W Portable Bluetooth Speaker Owner’s Manual

: June 6, 2024
: LG

Table of Contents

LG PL2W-Portable-Bluetooth-Speaker
ASSEMBLY AND SAFETY
AT A GLANCE
Remote control buttons
PREPARATION/CONNECTION
Connecting
WALL MOUNTING
OPERATION
Bluetooth mode
OPERATION
INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LG PL2W-Portable-Bluetooth-Speaker

ASSEMBLY AND SAFETY

Please read the following instructions before assembly:

The Soundbar is designed for audio playback. All other uses are expressly excluded.
If you want to set up the Soundbar on shelving units, in cupboards, etc., please ensure that there is adequate ventilation. There must be a free area of at least 10 cm on either side and above the Soundbar.
Do not cover the Soundbar with newspapers, tablecloths, curtains, etc.
When setting up the Soundbar, please note that furniture surfaces may be covered with various finishes or synthetic materials that often contain chemical substances. These substances can attack the material of the unit base among other things.
This can leave residues on the furniture surface, which may be difficult or impossible to remove.
If the Soundbar is subjected to big variations in temperature, for example when transported from a cold to a warm place, do not use the Soundbar for at least two hours.
The Soundbar is designed to be used in dry rooms. Should you nevertheless decide to operate it outdoors, you must ensure that it is protected from moisture (dripping or splashing water).
Only use the Soundbar in a temperate climate.
Do not place the Soundbar close to a radiator or in direct sunlight; this can affect the cooling system.
Do not place any containers with liquids inside (e.g. vases) on top of the Soundbar.
Do not place any open sources of fire (e.g. candles) on top of the Soundbar.
Do not use any cleaning agents; these may damage the casing. Cleanse the device using a clean and dry cloth.
Do not expose the battery to extreme heat, such as for example sunlight, radiators, fire, etc.
The remote control contains a button cell. Please always keep the remote control and the button cell out of reach of children.
If the button cell is accidentally swallowed, it can lead to burns and even death within two hours.
You should therefore see a doctor im-mediately Keep new and used batteries out of reach of children
. If the battery compartment cannot be closed safely, do not continue to use the device and keep it out of reach of children.
Remove the battery if used up or if you do not use the device for a long time. We do not assume liability for damage caused by leaked batteries.
The batteries, even those free from heavy metals, must not be disposed of as domestic waste. Used batteries must be discarded in used battery collection containers found at commercial or public waste management services.
You must never open the Soundbar. In case of damage due to improper tampering, any claims for guarantee are lost.
Storms are a danger to any electronic device. Even if the Soundbar is switched off, it may still become damaged as a result of lightning striking the mains. In case of a storm, you must always pull the mains plug.
Notes:
7 Do not connect any devices when your de- vice is switched on. Also, switch the other devices off before connecting them! 7 Do not plug the mains plug of your device into the socket until all external devices have been connected!
Please ensure that the mains plug is freely accessible!

RF Exposure Warning

This equipment must be installed and operated in accordance with the provided manual. The device comprised a built-in antenna, and must not be co-located or operating in conjunction with any other antenna or transmitter.

AT A GLANCE

See the figure on page 3. Front panel DISPLAY SCREEN REMOTE SENSOR Rear panel HDMI AUX INPUT OPTICAL DIGITAL AUDIO INPUT Side panel

Switches the device on from standby mode and back off again.
Switches in between the playback sources
USB port for playback and software update
Volume down
Volume up
Selects the source device connected to the »LINE IN« jack.

Remote control buttons

Switches the device on from standby mode and back off again.
Volume up
Selects the previous track.
Starts playback mode and switches between play/pause.
Volume down
Audio return channel
Mutes the Soundbar speakers and unmutes them again.
Press briefly to select the source device “Bluetooth”, ”USB”, ”LINE IN”, “AUX IN”, “OPTICAL IN” or “ARC”.
Selects the next track.
Repeats the last played song. Stops the playing music.

PREPARATION/CONNECTION

PreparationActivate the remote control battery
Remove protection film from the battery compartment. The remote control is now functional.

Change remote control batteries (TYPE AAA)

Note: If your device no longer responds to the remote control commands, the battery may be dead. It is imperative that dead batteries be removed. We do not assume liability for damage caused by leaked batteries.

Caution:
The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.

Hold the remote control with the backside facing up.
Push the detent of the battery holder to the right and remove the battery holder.
Remove the used battery and insert a new battery into the battery holder, positive pole facing upward
Push the battery holder into the remote control. it clicks into place.

Connecting

Connect Soundbar to the LCD TV

1.  Connect a standard audio lead to the **AUX INPUT** « jacks of the Soundbar. Please be aware of the left and right channels when doing so (white = left channel, red = right channel).

Connect audio leads to the audio output jacks of the LCD TV.

Connect external device
An external device, such as an MP3-Player for example, can be connected to the »AUX IN« jack.

Connect a standard audio lead to the AUX IN« jack of the Soundbar.
Connect the adapter cable to the external device.

Note: The LCD TV can also be connected via the AUX IN« jack if it is not equipped with audio output jacks. In such cases please use the headphone jack.

Connect mains cable
Check that the mains voltage indicated on the type label (on the back of the device) corresponds to the local mains voltage. If this is not the case, please consult your specialist dealer. Plug the mains cable plug into the socket (100 – 240V~ 50/60Hz).
Caution:
The Soundbar is connected to the mains via the mains cable. If you want to disconnect the Soundbar from the mains completely, you must pull the mains plug. Please ensure that the main cable is freely accessible during operation and is not obstructed by any other objects.

Subwoofer Connection

Make sure the AC power cord is connected to a power supply securely.
Subwoofers have wireless Bluetooth to receive the audio signal from the soundbar. When the blue indicator flashes, the subwoofer is in searching for Bluetooth signal status, the blue indicator keeps lighting means Bluetooth was connected, if the subwoofer can not connect with the soundbase automatically, please press the pair button on the rear panel of the subwoofer to reconnect
The subwoofer will memories the soundbar and repair it automatically when you power off the subwoofer and then power it on

WALL MOUNTING

In order to prevent injuries, the sound base device must be securely fastened to the wall in accordance with the below installation instructions.

Caution:

The ground must be firm and capable of handling the load.
Use mountings that are appropriate for the weight of the device.
For wooden or hollow wall structures use suit-able plugs and screws. Seek advice from a specialist dealer.

Warning:
In order to prevent injuries, the device must be securely fastened to the wall in accordance with the installation instructions.

Note: Installation of the Soundbar GSB 910 SW for professional use (e.g. in a bistro) must only be carried out by an electrically qualified person, in accordance with the applicable construction regulations as per VDE 0100.

1.  Drill the two holes(about 6mm in diameter ) in the wall and keep the distance between the drill holes of the soundbar is 500mm (Diagram 1).

Insert the two plugs supplied into two drilled holes and then insert two screws supplied into two holes and tighten (Diagram 2).
Take care to leave 4 mm between the screw heads and wall (Diagram 3).
Use the assembled soundbar to hang on the setscrews on the wall (Diagram 4).

OPERATION

AUX IN/LINE IN
This sound base has two extra groups of audio input terminals. You can input the analog audio signals from extra devices such as VCD, CD, VCR, DVD players, etc. Use the audio cable to connect the stereo audio output terminals of a VCD, CD, VCR, DVD player to the stereo input terminals AUX-IN/LIN this sound base. Its corresponding signal source is AUX-IN/LINE IN which can be available by pressing [SOURCE] on the remote control.
Optical Input
Soundbar Connect LCD TV (digital Signal)
Connect a commercially available optical cable to the »OPTICAL« jack of the Soundbar.
Connect the optical cable to the sound output socket of the LCD TV (optical, PCM signal).

NOTE
The TV audio output must be set to PCM. – AUX IN – L« jack of soundbar left and right channel. (white = left channel, red = right channel) Connect the audio cable to the sound output socket of the LCD TV
Note:
Choose appropriate analog audio output on TV

ARC(AUDIO RETURN CHANNEL)
ARC is an audio return channel function, it is used in the digital audio output of liquid crystal display television in order to get the optimal synchronous sound quality. Use the HDMI cable to connect the HDMI-ARC input port of this sound base to the ARC output port of the liquid-crystal display television.

Bluetooth mode

LG PL2W-Portable-Bluetooth-
Speaker-9

Your device can be paired with all current, Blue-tooth-enabled devices applying to smartphones, laptops, and tablet PCs for example.

Press standby button » 8 « to power on the sound base.
Press the source button » « to switch the corresponding Bluetooth mode.–The bt will be flashing quickly in the display .screen.
The sound base is in searching Bluetooth signal status.
Use your smartphone to search for the Bluetooth signal of the sound base.
Select ”Grundig Soundbar 2.1” on your list. 6 The sound base will synchronize to play songs on your mobile phone while the bt keep solid light in the display screen means to be connected successfully.

OPERATION

Disconnected the Bluetooth on the smartphone to switch off the Bluetooth connection.
Note: Bluetooth connection range in 10 meters 7 The model ”Grundig Soundbar 2.1” in your device was not deleted.
In Bluetooth mode, »I«, » «, » «, »+«, –« etc. are also active.

Remote control operation

Insert the batteries into the remote control.
Point the remote control at the remote sensor on the front panel.
The sound base is in searching Bluetooth signa status.

The remote control works within a distance of about 8 meters from the sensor and within an angle of about 30 degrees from the left and right side.

Battery installation

Remove the battery compartment cover on the back of the remote control.

2 Load one AAA/1.5V battery into the battery compartment making sure that the battery has been inserted with the correct polarities match-ing the symbols +, – as indicated inside the battery compartment.

3 Replace the cover

Note: Remove the battery when you do not intend to use the remote control for a long time. 7 Weak batteries can leak and severely damage the remote control. 7 The battery must not be exposed to excess-
I’ve heat sources, such as sunshine, fire, or any other things like that. 7 Be environmentally friendly and dispose of batteries according to your government regulations.

INFORMATION

Technical Information
This device is noise-suppressed according to the applicable EU directives. This product fulfills the European directives 2014/53/EU, 2009/125/EC, and 2011/65/EU. You can find the CE declaration of conformity for the device in the form of a pdf file on the Grundig Homepage at www.grundig.com/downloads/doc.
Power supply: 100-240V~ 50/60Hz
Max. power input:
Power consumption: 20W, Standby ≤ 0.5 W
Power output: DIN 45324, 10% THD 2 x 20 W
Frequency response : 20 Hz – 20 kHz
BT frequency : 2402 – 2480 MHz
BT maximum output power: 7.2 dBm
S/N ratio : ≥ 70 dB
Separation: ≥ 45 dB
Dimensions and weight: W x H x D 88 x 6.2 x 8 cm Weight approx. 1.88 kg Subwoofer
Power supply: 100-240V~ 50/60Hz
Max. power input: Power consumption 25 W, Networked Standby ≤ 2 W
Power output: DIN 45324, 10%THD 1x40W Dimensions and weight: W x H x D: 20.0 x 32.0 x 23.0 cm Weight approx.: 3.0 kg Technical and design modifications reserved!

Compliance with the WEEE Directive and Disposing of the Waste Product: This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

This symbol indicates that this product shall not be disposed of with other household wastes at the end of its service life. Used devices must be returned to an official collection point for the recycling of electrical and electronic devices. To find these collection systems please contact your local authorities or retailer where the product was put-chased. Each household performs an important role in recovering and recycling old appliances. Appropriate disposal of used appliances helps prevent potential negative consequences for the environment and human health.
Compliance with RoHS Directive
The product you have purchased complies with the EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive. Package information packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the pack-aging material collection points designated by the local authorities.