tonivent TON007B Bluetooth Cassette Player Converter User Manual
- June 6, 2024
- tonivent
Table of Contents
tonivent TON007B Bluetooth Cassette Player Converter
PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
Buttons and connections:
- Play
- Auto reverse (DIR)
- PlayMode
- Fast Forward
- Stop
- Rewind
- Volume control knob
- Earphone slot
- FM mode
- Volume Up/Last play
- Play/Stop(Bluetooth mode)
- Bluetooth mode
- Volume Down/Next play
- LED light
- Battery cover 16. DC-In
Product features:
- Used as a walkman, play cassette tape music everywhere.
- With Bluetooth out function, can transmit the music to other Bluetooth receivers.
- With Auto-reverse function
- FM mode can receive radio(with 3.5mm earphone as an antenna)
- 3.5mm earphone jack
Operation:
- Earphone slot: enjoy music when earphones are in the slot.
- When playing music, you can use the volume control knob to adjust the volume.
- Press “DIR” button to auto-reverse the cassette.
- Press the “PLAY” button to play the cassette.
- Play Mode: Selects what the cassette does when it reaches the end of aside. When set to the “loop” icon, the cassette will automatically switch direction and begin playing the opposite side when one side has finished. When set to the single arrow icon, the cassette will simply stop when a side has finished.
- Press the “F.F” button to Fast Forward the cassette.
- Press “REW” button to Rewind the cassette.
- Press the “STOP” button to stop playing the tape and the Bluetooth connection will also be disconnected.
How to Connect to Bluetooth Receiver?
Please make sure to turn on your Bluetooth receiver devices at first. Then Put
2*AA batteries(Not included) into the battery case or used by DC power(Not
included) .
- Long press the Bluetooth button 3 seconds to turn on the Bluetooth function, led white light on and fast flash, will auto search and pair the Bluetooth receiver, Put in the tape and press the “PLAY” button. When the device successfully pairs the Bluetooth receiver, led white light keep on, Don’t put the earphone in the slot when Bluetooth opens.
- If it does not have any Bluetooth device to connect to, after the LED white light fast flash for a while, Bluetooth will auto turn off.
How to connect a Mobile phone to Bluetooth and use FM?
- Earphone(or speaker with 3.5mm Aux male) plug into earphone slot, Long press Bluetooth button 3 seconds to turn on, press FM button to search radio,led light turn to blue and flash,
- When the voice announces Bluetooth mode on, turn on Bluetooth on the mobile phone, search and pair device “HC01”, led keep blue light on means connect successful, mobile phone audio play through earphone or speaker. Press the”+” or ”-” button to adjust the volume.
- On FM mode, press the PLAY/STOP button to search the radio, and press the”+” or ”-” button to adjust the channel.
- When FM mode on/ mobile phone Bluetooth connection, you can not Play cassette.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.