MUSIC WAVE MW111 USB Media Player Instruction Manual

MW111 USB Media Player
Instruction Manual

Please read the instruction manual carefully before operating the unit

Safety Instruction

CAUTION This symbol with “CAUTION ” is intended to alert the user to the presence of important instructions. Failure to heed the instructions could result in injury or unit damage.
To prevent injury and damage to the unit, please read and follow the instruc­tions in this manual. If you feel unsure about installing this system yourself, have it installed by a  qualified DS18 technician.
Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire, and/or possible injury.

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide more reasonable protection against harmful interference in a residential installation.
Operation is subjected to the following two conditions:
(1) This device may not cause harmful interference, and(2) the device must accept any interference received, including interference that may cause unde­ sired operation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm­ full interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or  television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Specifications

50 W x 4 @ 2 Ohms Peak
Max. RCA Output Voltage| 4V
Output Impedance| 5000
Frequency Response| 20— 20 kHz
FM Frequency Range| 87.5 – 107.9 MHz
AM Frequency Range| 530 — 1710 kHz
WB Frequency Range| 162.40-162.55 MHz
Tuner Presets| 18 FM / 12 AM/6WB
Display| 3″ Full Dot Matrix LCD Gorilla Glass
Bluetooth| 5.0+EDR, A2DP
USB Compatibility| 2.0
USB Capacity| 64 GB max
USB Charger| 1A
Audio File Compatibility| MP3, WMA

Installation/ Mounting

Installation

CAUTION

1. This player should be installed by a professional technician.
2. Please read the instruction and operation of the equipment carefully before installing it.
3. Make sure to connect other wires before power connection.
4. To avoid short circuits. Please make sure all the exposed wires are insulating.
5. Please fix all the wires after installation.
6. Please make a connection to the player accordingly to this instruction manual. A wrong connection may cause damage.
7. This player is only fit for 12V DC devices and please make sure your boat belongs to this kind of cathode grounding electrical system.
8. Please connect the wires rightly. A wrong connection will cause malfunction or damage the electrical system.

Mounting (Using U Bracket)
To mount the unit, you will need to find a flat surface with adequate clearance behind it that provides enough clearance for the unit and all it’s necessary wiring.

1. Once you have determined a mounting location, you will need to cut a circular hole 3 ” (77mm) in diameter.
2. After the hole is cut slide the unit and wiring through the hole.
3. Take the U bracket and slide over the two studs on the back of the unit. Tighten down with supplied nuts.
4. Plug in all wiring harnesses and cables. Refer to the wiring diagram for wire harness connection types.

Wiring Connection

CAUTION

1. This player can only be used by the 12V DC cathode grounding electrical system.
2. Don’t connect the terminals of the battery until the player is abso­ lutely with a good erection joint.
3. Please make sure to connect the yellow wire to the positive of the battery(+).
4. When changing the fuse. Please make sure the specifications are the same.
5. Using good quality speaker with 4 ohms can result in the best effect on the equipment.

Basic Operation

1. CD POWER/ button
   Press the (‘button to turn it on. Press the key again to turn off the unit.

2. BAND/button
   Press the BAND button to FM1/FM2/FM3/AM1/AM2/WB. Press and hold the BAND button for 3 seconds to auto store the stations.

3. DIP/button
   Shortly press the DISP button to show the clock, then press and hold the DISP button again to set time, Rotate Vol to set hour time display, press DISP key again to turn to minute time display, rotate Vol to set minute time display.
   After setting the time, it will automatically save and exit within 5 seconds.

4. ZONE/button
   Press the ZONE button to ZONE1 /ZONE2 / ZONEl+ZONE2.

5. PLAY/PAUSE button
   In RADIO/AUX source press the button for the MUTE on/off function. In the USB/BT source press the button for the Pause/Play function.

6. Seek UP button
   In RADIO source, shortly press the button to Seek up, press and hold the button to show the next station. In the USB/BT source press the button to the next song/file, press and hold the button to fast forward play.

7. Seek down button
   In RADIO source, shortly press the button to Seek down, press and hold the button to show back to the previous station. In USB/BT source press1button to the previous song/file and press and hold the button to playback quickly.

8. SRC button
   Press the SRC button to Mode change Radio/BT/USB/AUX-IN.

9. VOL/SEL button
   Rotate the Vol to adjust the volume.

IN ZONEl or ZONE2, AUX/BT mode:
Shortly press the SEL button to BAS/TRE/SUB/EQ(rotate the VOL to select FLAT/OFF, S-BASS,VOCAL, POWERFUL,
CLARITY)/LOUD(ON/OFF)/COLOR LIGHT(rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN)/BEEP(0FF/ON) one by one.
Press and hold the SEL button to TA(OFF /ON )/AF(OFF/ON)/NEWS(OFF/ON) one by one.

IN ZONE1 or ZONE2, RADIO mode:
Shortly press the SEL button to BAS/TRE/SUB/EQ(rotate the VOL to select FLAT/OFF, S-BASS, VOCAL, POWERFUL,
CLARITY)/LOUD(ON/OFF)/COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN) /BEEP(ON/OFF)/STEREO(MONO)/LOCAL(DX) one by one.
Press and hold the SEL button to TA(OFF/ON)/AF(OFF/ON)/NEWS(OFF/ON) one by one.

IN ZONEl or ZONE2, USB mode:
Shortly press the SEL button to BAS/TRE/SUB/EQ(rotate the VOL to select FLAT/OFF, S-BASS, VOCAL, POWERFUL,
CLARITY)/LOUD(ON/OFF)/COLOR LIGHT(rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN)/BEEP(0FF/ON) one by one.
Press and hold the SEL button to RDM( then rotate the VOL to select OFF/FOLD/ALL)/RPT(then rotate the VOL to select ONE/FOLD/ALL)/TA(OFF/ON)/AF(OFF/ON)/NEWS(OFF/ON) one by one.

IN ZONE1+ZONE2, AUX/BT mode:
Shortly press the SEL button to COLOR LIGHT(rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN)/ BEEP(OFF/ON) one by one.
Press and hold the SEL button to TA(OFF/ON)/AF(OFF/ON)/NEWS(OFF/ON) one by one.

IN ZONEl+ZONE2, RADIO mode:
Shortly press the SEL button to COLOR LIGHT(rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN)/ BEEP (OFF/ON)/  STEREO(MONO)/LOCAL(DX) one by one.
Press and hold the SEL button to TA(OFF/ON)/AF(OFF/ON)/NEWS(OFF/ON) one by one.

IN ZONE1+ZONE2, USB mode:
Shortly press the SEL button to COLOR LIGHT(rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN)/ BEEP(OFF/ON).
Press and hold the SEL button to RDM(then rotate the VOL to select OFF/FOLD/ALL)/RPT(then rotate the VOL to select ONE/FOLD/ALL)/TA(OFF/ON)/AF(OFF/ON)/NEWS(OFF/ON) one by one.

Function setting/Operation

Setting
DX/LOC (Distance/Local):
LOC: Receive the strong signal station only in seek station.
DX: Receive strong and weak signal station in seek station.
STEREO/MONO:
STEREO: Receive FM stereo signal.
MONO: Change FM stereo to monochrome. It can reduce the noise when the signal is weak.
Reset the unit
Press and hold the button for 5 seconds to reset the unit.

Radio (AM/FM/WB) Operation
Press the SRC button to select the Radio source option(FM/AM/WB).
To auto seeks station, press and hold the BAND button for 3 seconds to the auto store radio station.
To manual seek the station, shortly press / button to Seek up/down the radio station, press and hold the / button to next/previous station.

USB Operation
After your device is connected to the source unit, this feature allows you to control the playback of your device directly from the unit. Press the SRC button to select the USB source option.
To play or pause a song, short press the PLAY/PAUSE button. To skip a track forward, short press the FWD button. To skip a track backward, short press the REV button.
To access USB-specific settings, Press and hold the SEL button for the list of settings (Random play>Repeat). Use the encoder to select the option to change.

AUX (Auxiliary Input) Operation
After your device is plugged into the source unit, this feature allows you to play music from your device. Press the SRC button to select the AUX source option and use your plugged-in device to control song/track selection, PLAY/PAUSE, and track skip FWD/REV.

Bluetooth Operation
After your device is paired to the source unit, this feature allows you to control the playback of your device directly from the unit. Press the SRC button to select the BLUETOOTH  source option. Then search and select the Bluetooth device “MRX2” from your phone and input the password “0000” If it needs.
When paired successfully, the BT symbol will be shown on the LCD.
To play or pause a song, short press the PLAY/PAUSE button.
To skip a track forward, short press the FWD button. To skip a track backward, short press the REV button.
To access USB-specific settings, Press and hold the SEL button for the list of settings (Random play>Repeat). Use the encoder to select the option to change.

Troubleshooting

Basic
Unit does not turn on| Blown fuse| Check the fuse of the unit, and replace it with the correct rating.
The vehicle’s ignition is off| If connected following the instructions,
the unit will not operate with ignition off
The voltage applied to the Red wire is not between 10.5 & 16 volts or there is no voltage present.| Check battery, connections, and fuses and repair or replace as necessary. If voltage is above +16 volts, have the electrical system inspected by an authorized service center.
The unit is not properly grounded.| Check wiring and repair as necessary.
Radio Tuner
Tuner fails to tune any stations| No antenna or disconnected or open connection in cable.| Check all connections and repair as necessary.
Unable to tune stations in seek mode| You are in a weak signal area.| Make sure the tuner LOC mode is off.
USB Devices
The USB device cannot be inserted| The USB device has been inserted in the wrong direction.| Reversing the connection direction of the USB device, try reinserting.
The USB device connector is broken.| Replace with a new USB device.
The USB device is not recognized| The USB device is damaged.| Disconnect the USB device and reconnect. If the device is still not recognized, try replacing it with a different USB device.
Connectors are loose.
No sound was heard with the display “No File” shown| No MP3/WMA files are stored on the USB device.| Store these files properly on the USB device.
Sound skips or is noisy| MP3/WMA files are not created properly.| Use MP3/WMA files that are encoded correctly.
AUX Input
MP3 is not playing back| Writing error occurred. The MP3 format is not compatible.| Make sure MP3 has been written in a supported format.
Bluetooth
Cannot pair Bluetooth| The Bluetooth function of the device is not enabled.| Refer to the user manual of the device for how to enable the Bluetooth function.
The audio quality is poor after connection with a Bluetooth enabled device| The Bluetooth reception is poor.| Move the device closer to the audio system or remove any obstacle between the device and the system antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>