FZF HZB-20F/SL 25kg Small Commercial Ice Maker User Manual

USER MANUAL
ICE MAKER

HZB-20F/SL

IMPORTANT SAFETY INSTRUCTIONS

Your safety and the safety of others are very important.
We have provided many important safety messages manual and your appliance.
Always read and obey all safety messages.
This is the safety alert symbol:

All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”.

DANGER
WARNING

These words mean:
You can be killed or seriously injured if you don’t immediately follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

PREPARING YOUR ICE MAKER FOR USE

IMPORTANT SAFETY TIPS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Do not operate this or any other appliance with a damaged cord. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This ice-maker must be positioned so that the plug is accessible . Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the receptacle.

• Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from traffic areas, and do not submerge in water. We do not recommend the use of an extension cord, as it may overheat and become a risk of fire. If you must use an extension cord, use No.0.75mm2 minimum size and rated no less than 16A/250V~ with a plug.
  WARNING: This appliance must be earthed.

• Unplug the ice maker before cleaning or making any repairs or servicing.

• Exercise caution and use reasonable supervision when the appliance is used near children.

• Do not use your ice-maker outdoors. Place the ice-maker away from direct sunlight and make sure that there is at least 6 inches of space between the back of your unit and the wall. Keep a minimum distance of 6 inches on each side of your unit free.

• Do not use other liquid to make the ice-cube other than water.

• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.

• Do not tip over. To avoid a hazard due to the instability of the appliance, it must be placed on an even or flat surface.

• If the ice maker is brought in from outside in the wintertime, give it a few hours to warm up to room temperature before plugging it in.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• This appliance must be earthed.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

• This appliance is intended to be used in household and similar applications such as
  – staff kitchen areas in shops, offices, and other working environments;
  – farmhouses and by clients in hotels, motels, and other residential type environments;
  – bed and breakfast type environments;
  – catering and similar non-retail applications.

• Warning: Risk of fire/flammable materials used. Please according to local regulations regarding disposal of the appliance for its flammable blowing gas.

• WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• WARNING: Do not damage the refrigerant circuit.

• WARNING: Do not use mechanical devices or other means to accelerate the defrosting process or ice harvesting process, other than those recommended by the manufacturer.

• WARNING: Do not use other types of electrical appliances inside the ice-maker.
  IMPORTANT:
  The wires in this mains lead are colored in accordance with the following code:
  Green and yellow: Grounding
  Blue: Neutral
  Brown: Live

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

• Young children should be supervised to ensure that they do not play with the appliance.

• -Please according to local regulations regarding disposal of the appliance for its flammable refrigerant and blowing gas. Before you scrap the appliance, please take off the doors to prevent children trapped.

GETTING TO KNOW YOUR UNIT

1. Water reservoir cover

2. Unit top cover

3. Water separator pipe

4. Evaporator

5. Ice basket

6. Ice scoop

7. Transparent window

8. Control Panel:
   A. Timer button
   B. Power button
   C. LCD Display area
   1. Ambient temp and ice-making countdown symbol: when the display show , ice-making countdown, when the display show < ℉>, means ambient temp.
   2 . Ice making and Ice harvest symbol: when the symbol is running, the unit is making ice cubes, when the symbol flash, the unit is ice harvest. 3ON/OFF symbol.
   4.  Error code E1-Ambient temp sensor breakdown.E2-refrigerating tube sensor breakdown
   5 . Lack of water warning symbol.
   6. Ice full warning symbol.
   7. Time setting display area. When show , timer unit ON/OFF, when show

   , setting ice making time. D. Ice making and timer reduction. E. ice making and timer increase.

9. Hot Air Outlet

10. Water draining port: To drain out the water from the unit.

OPERATING PROCEDURES & MAINTENANCE

UNPACKING YOUR ICE MAKER

1. If any parts are missing, please contact our customer service.
2. Clean the interior with lukewarm water and a soft cloth. Take out the ice basket and clean it
3. Find a location for your ice maker that is protected from direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at least 6 inches of space between the back and sides of your ice maker and the wall.
4. Allow one hour for the refrigerant fluid to settle before plugging the ice maker in.
5. The appliance must be positioned so that the plug is accessible.

WARNING: fill with potable water only.

CONNECTING YOUR ICE MAKER

DANGER

* Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged please call our customer service.

1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug that mates with standard three-prong wall outlets to minimize the possibility of electric shock.
2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician.
3. This appliance requires a standard 220-240volt, 50Hz electrical outlet with a three-prong ground.

CLEANING AND MAINTAINING YOUR ICE MAKER

Before using your ice maker, it is strongly recommended to clean it thoroughly.

1. Take out the ice basket.
2. Clean the interior with diluted detergent, warm water, and a soft cloth.
3. Then use the water to rinse the inside parts, and drain out the water from the draining port by unplugging the drain cap on the back.
4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
5. Dry the interior and exterior with a soft cloth.
6. When the machine is not in use for a long time, open the water drain cap to drain the water completely out of the water reservoir.

After using your ice maker for a long time, we also suggest you should clean your unit. Especially to the water separator pipe and the water filters, you must clean them periodically.

1. If the water separator pipe is blocked and there is no water flowing down when you listen to the compressor and the water pump inside is still working, please turn off the unit first and disassemble this pipe, and clean it. Clean each hole on the pipe wall displayed in the following picture. After cleaning, install back the water separator pipe and be sure the right terminal of the pipe connects to the silicone pipe well and as the original.
   

2. For both the water tank and the big water reservoir, clean them with diluted detergent, warm water, and a soft cloth. Then use the water to rinse the inside, and drain out the water from the draining port by unplugging the drain cap on the back. It will help you keep the unit and ice cube hygienic, and also make the unit work normally.

3. When cleaning, if find that the ice cube is left on the evaporator and can not be taken out easily, you can turn on the unit to let the unit enter the ice making process, then press the “ON/OFF” button for more than 5 seconds to let the unit start ice harvest process to melt the ice cube. It will help you remove the hard ice cube.

How to drain out the water from the internal tank and big water reservoir completely
Because the water in the big water reservoir is stopped to drain port by the water valve, if you want to drain away all the water, please plug on the unit and but don’t start the unit, then remove the drain port cap at the back. Wait some minutes, and all of the water will flow out.

USING YOUR ICE MAKER

Operation panel and display area

1. Remove the cover of the water reservoir and pour potable water into the water reservoir. And be sure to keep the water level below the max. level with the FULL mark displayed in the following picture. Then move back the cover at once to avoid foreign matter enter.
   Warning: Do not pour the water into the internal water tank located underneath the ice basket. This tank is not big enough and will affect the ice-making performance.

2. When you plug the unit, the power symbol< > will flash. Press the <ON/OFF>button, the unit will start making ice cubes, ice-making symbol< > will keep running. The left up corner of the display area will show the ambient temp,i.e:80 ℉ means the ambient temp is 80 ℉. After several mins, this area will show a flash number, the ice making will countdown,i.e:10M means the ice making will finish 10 mins later.

3. When the ice maker harvests, symbol< > flash, the water will flow from the topwater reservoir to the bottom water tank through the solenoid valve, the symbol < > will be on, when the water in the bottom water tank is full, the symbol < > will be off, then the next ice-making cycle start again. When there is no water in the water reservoir, the symbol < > will keep on. Turn off the unit and fill water again, then restart the unit to make an ice cube. Or fill water directly and wait 20mins, the unit will restart.|
   Remark: The ice-making cycle lasts about 13 to 25 minutes, depending on the ambient temperature. And for the first time, according to the initial water temperature, ice-making last time will be a little longer. In the extreme hot room temperature, ice-making time may be Vary a lot, but it will not exceed35minutes.
   If you think the ice cube is not thick enough, during ice making, press the< + >and< – >to set the ice-making lead time. Press one time and the ice-making cycle will increase or Reduce one min,6minmost. This can only start from the news cycle.

4. When Ice Full symbol< >is on, the unit will stop, take out the ice cube inside, and the unit will start working again.
   If press the button< ON/OFF >more than 5s, when the ice maker is working, the unit will start harvesting. Press the button<ON/OFF>, and the unit will turn off.
   Timer setting.Unit on timer setting, When the unit is working, the timer setting the unit off.Unit off
   Timer setting, When the unit is off, timer the unit on.
   Press the button, the display will show< 1H >, and then press <+>and<->to set the time. During the setting, the His flash, after 5s, the H will keep on and unit will be in your Timer setting.

5. Water Drain: take off the drain plug cap on the back of the unit, take out the silicon plug, then drain the water inside. It is better than exchanging water every 24hours.and cleaning the unit every3days.

Warning

A. make sure the water tank, water filter, and water separator pipe are not blocked, clean them
B. The water temp will affect the ice-making capacity. The lower temp, the more ice cube produced.
C. The cooler the ambient temp, the more ice cube produce.
D. always uses good quality water to make sure the pump works well. Bad quality water will cause pump noise but doesn’t affect the unit’s working.
E. The compressor restart 3mins later if you turn off the unit.

TROUBLESHOOTING

PROBLEM| POSSIBLE CAUSE|

SOLUTION

---|---|---
< ** > is on**| Lack of water| Turn off the unit and add water to