IDENTIV uTrust 5501 F OBA Multi-Technology Smart Card Reader Writer Module User Manual
- June 6, 2024
- IDENTIV
Table of Contents
**IDENTIV uTrust 5501 F OBA Multi-Technology Smart Card Reader Writer Module User Manual
**
Author
|
Identiv
---|---
Version
| 1.3
Date|
14-DEC-2020
Document History
Version
| Date| Description of Change|
Author
---|---|---|---
1.0| 26-OCT-2020| Initial version| Identiv
1.1| 29-OCT-2020| Added host pinout, mating connector information Clarified
test procedure applicability|
1.2| 10-NOV-2020| Updated FCC statements|
1.3| 14-DEC-2020| Included ISED statement in French|
Scope of the document
The user manual specifies the basic application of the reader by the customer.
Identiv uTrust 5501 F reader family
Identiv uTrust 5501 F is a family of USB based contactless card reader. The readers connect to a host PC via USB 2.0 Full speed interface. They support ISO14443 and ISO15693 cards in HF mode and 125 KHz LF cards. The information in this manual applies to the devices model numbers listed below along with their respective part number, FCC ID and ISED ID:
Part Number
| Product Name| FCC ID|
ISED ID
---|---|---|---
905567| uTrust 5501 F HF + LF| MBPUT5501F-01| 7485A-5501F01
905567-2| uTrust 5501 F HF + LF DTC| MBPUT5501F-01| 7485A-5501F01
905567-3| uTrust 5501 F HF| MBPUT5501F-01HF| 7485A-5501F01HF
Driver Installation in Windows
Follow the sequence of steps to install the driver
- Plug in the reader to a Windows PC
- The PC prompts for a driver
- Select Microsoft CCID driver and install the driver
- The device enumerates with Identiv VID and PID strings
Host Communication Interface
Host communication is through the 1×5 header marked USB host.
Pinouts for USB host connector is as below:
PIN #
| Signal
---|---
1|
Vbus
2
|
D-
3
| D+
4|
GND
5
|
Shield
The mating connector/receptacle for the header is TE Connectivity 440129-5
Communication with Card
Follow the procedure described below if module is tested in standalone mode when it is not integrated into any device.
Follow the sequence of steps to communicate with the SAM card,
- Plug in the reader to a Windows PC and load the driver
- Launch the PCSCDIAG Utility
- Insert the contact card into the card slot of the reader
- Check the ATR of the card being displayed in the PCSCDIAG Utility.
Follow the sequence of steps to communicate with the contactless card,
- Plug in the reader to a Windows PC and load the driver
- Launch the PCSCDIAG utility
- Place a contactless card on top of the reader
- Check the ATR of the card being displayed in the PCSCDIAG Utility.
To test the module after integration into device, follow the procedure from device manufacturer.
FCC Statements
FCC PART 15.105 STATEMENT: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC PART 15.19 STATEMENT: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC PART 15.21 STATEMENT: NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
ISED Statement
The device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference received, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>