Tcl Technoly Electronics OH000024 Eaton Voice Dimmer User Manual

Tcl Technoly Electronics OH000024 Eaton Voice Dimmer

PRODUCT OVERVIEW

WARNINGS AND CAUTIONS

• Turn OFF circuit breaker orreroove fuse!s) and test that the power is OFF before starting the installation process
• Never wire any electrical device with power turned ON
• If you are not sure about any part of these instructions, please contact a licensed electrician
• If bare copper or green ground connection is not available in the wallbox, contact a licensed electri cian for installation
• Use only #14 or #12 copper wire rated for at least 75 degrees Cwith these devices. DO NOT USE ALUMINUM WIRE

CAUTION

• Use only with 120V/AC 60Hz
• Do not exceed the maximum rating of the dimmer as indicated on the device
• Must be installed and used in accordance with all national and local electrical codes
• Suitable for installation in outlet box measuring a minimum 3″ x r x 2 1/2″ deep and wired in accordance with NEC article 314 box fill requirements

IMPORTANT

• The dimmer will not work. or will be damaged if wired incorrectly and the warranty will be voided Refer to the wiring instructions provided
• Wiring dimmer HOT may cause permanent damage to dimmer and void warranty

OPERATION INSTRUCTIONS

• Press the ON/OFF button to turn the lights ON
• Press the button again to turn the lights OFF
• Pull the air gap switch to disconnect power to the load

QUICK MAX

• When the lights are OFF. press and hold the ON/OFF button for 2 seconds. The device will then instantly tum ON at its maximum brightness level

FACTORY RESET

The dimmer can be reset which will exclude it from its network and restore all factory defaults.

• Press and hold the Privacy DUtton for 30 seconds. Upon successful completion, the LED indicator bar will slowly fade in and out and orange color to indicate that the deviCB is nowunregistsrsd and ready to be setup again.

DIMMER RATING

| Load Type| S i ngle G a ng| 2-Gang| 3 – G a n g
---|---|---|---|---
WFAV D 3 1 0| CFL/LED/FLIR/MLV/INC/HAL/ELV| 300w| 300w| 200W

For more advanced configuration parameters such as adjusting the LED indicator bar brightness and other features, please visit: Eaton.com/SmartHome

WIRING DIAGRAMS

Single location control installation

Two locotion control installation using a standard 3-way switch

Multi-l1cdion conlral installation uining a standard 3-way Switch

Get your Wi-Fi smart voice dimmer running in 3 easy steps!

Step 1: Install your Wi-Fi smart voice dimmer per the instructions provided in this booklet

Step 2: Download the Amazon Alexa app via the App Store

|
---|---

Step 3: Add your device to the Amazon Alexa app in a few easy steps:
a) Select “ Devices ” option

b) Select “ + ” option to add device

c) Select “ Add Device ” option

d) Select device type: – Switch

e) Select Eaton as the brand
f) Select sub-type Voice Dimmer Switch
g) Follow the steps in the Amazon Alexa app to finish setting up your Wi- Fi smart voice dimmer.

Issues setting up or using your device?

Q: Device not working. load does not come on, LED indicator bar not functioning
A: -Check to make sure your breaker is turned on
– Make sure the air gap switch is pushed in
– Make sure wiring is correct by following the provided wiring instructions closely

Q: Lights are flickering
A: -Make sure wiring is correct by following the provided wiring instructions closely
– Make sure wiring is not loose
-Adjust the minimum brightness level to a higher level*

Q: Alexa is not working
A: -Make sure your device is registered in the Amazon Alexa app using the instructions provided
– Check that your internet connection is working
– Pull the air gap switch and push it back in to rebootthe device

Q: Device unable to connect to Wi-Fi
A: -Check thatthe router is powered on
– Check that you have the correct network name and password
– Make sure your Wi-Fi router is in a location that is suitable for good signal quality.

Still having issues? Visit Eaton.com/SmartHome or contact us at 1-866-153-4293, option 2 for more help.
*Visit www.eaton.com/smarthome to adjust the minimum brightness level

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>