Shenzhen Michuang Technology TD01 Smart Solar Pathway Lights User Guide
- June 6, 2024
- Shenzhen Michuang Technology
Table of Contents
Shenzhen Michuang Technology TD01 Smart Solar Pathway Lights
Warning
- Please check if the light and the parts are intact before installation.
- Please make sure that the batteries are intact and well installed before use, if they are damaged, please stop using them.
- Please take off the cover of the light, flip the toggle switch under the cover to the “ON” or “FADE” mode to make sure the light works at night.
- This smart solar pathway light comes with a Light Control Function, which means that it will automatically light up in the darkness, and shut off during the daytime.
- Please install the lights in a place where allows the lights to get fully exposed to Sunlight to complete the charging process.
- Please plug it vertically into the soft ground to avoid a
- The farthest distance for the mobile phone APP to control the lights is no more than 32ft(10m), to control the light efficiently please make sure that all lights are within 32 ft of your phone.
- The phone APP can control up to 6 lights at the same time, you are able to preset the colors and modes according to your preference. damage to the lights.
Specification
| P/N | MWSS02RGBW | MWSS06RGBW |
|---|---|---|
| Quantity | 2-pack | 6-pack |
| Model | TD01 | |
| Color | RGB+Warm Light | |
| Power | built-in 1000mhA battery （Solar charging） | |
| Protection Rating | IP65(Only Solar panels) | |
| Controlled By | Phone App | |
| Remote Control Distance | Max. 10m | |
| Life Span | 30000H | |
| Working Temperature | -40°C~60°C |
Dimension
Phone APP Control Methods
- Support: Bluetooth 4.0 above
- Phone Support: ios 11 or above and android 4.4 or above.
- Language support: English
- APP name: LotusLantern
APP Connection Instructions
Step One: Open APP and enter the RGB color setting.
Choose lighting colors on the color wheel and adjust brightness by dragging the slider bar below.
Lights will be connected automatically to the APP when the Bluetooth function is activated on your phone.
Enter shake mode by clicking “Setting” button.
Step Two: Enter “Mode” for lighting modes and speed setting.
Step Three: Enter “Music” setting to play your favorite music, and lighting will dance with the music.
Step Four: Enter “Microphone” setting, to choose built-in Mic, which use the microphone function on your phone to receive audio and change lighting colors accordingly.(These lights come without external Mic, this feature is useless, please ignore it.)
Step Five: Enter “Timer” for lighting schedule setting;
If the Bluetooth connection is not successful, check the possible causes by following the steps below.
- Please make sure that the switch under the cover is flipped to the “ON” or “FADE” mode.
- Please make sure that your phone’s Bluetooth is turned on.
- Please make sure the lights are within 32ft(1Om) coverage of the mobile phone.
- Please check whether the light can light up normally at night, if not, the battery may be out of power, please charge the light under the sun until it can be used normally.
- This lighting kit adopts the Bluetooth 4.0 version, which only supports connection with one phone. Check if the lighting kit has been paired to a phone. If yes, please disconnect it with the previous phone and pair it to yours.
- Check if the Bluetooth is successfully paired to the lighting kit. If not, exit the APP and restart it to connect the lighting kit again.
- If the Bluetooth connection still fails after restarting the APP, please exit the APP and reboot your phone.
- Please note that the mobile APP can connect up to 6pcs of lights at the same time.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm between the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>