STEELGREEN MANUFACTURING SG36 Snow Plow Attachment Instruction Manual

: June 13, 2024
: STEELGREEN MANUFACTURING

Table of Contents

STEELGREEN MANUFACTURING SG36 Snow Plow Attachment
SNOW PLOW KIT INSTRUCTIONS
Installation Instructions
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

STEELGREEN MANUFACTURING SG36 Snow Plow Attachment

SNOW PLOW KIT INSTRUCTIONS

Installation Instructions

NOTE

If your machine is already equipped with the hydraulic lift kit (A10081) proceed to step eight.
Some parts not shown for clarity.

STEP ONE

Set the plow hitch in the frame by resting the front of the plow hitch on top of the frame rail and the back of the hitch will attach to the bottom of the frame rail.
ASSEMBLY TIP: Use a floor jack or block of wood to support the back of the plow hitch.
Attach the plow hitch to the frame using the top brackets and (6) 3/8” X 2-3/4” carriage bolts and (6) 3/8” nuts provided with the kit.

NOTE: Note the orientation of the back brackets.

Be sure the tab is facing the correct direction (One will face left and the other will face right) so the hitch is centered in the frame.
After the hitch is tightened to the frame adjust the exhaust shield so it rests in the grooves of the plow hitch.

STEP TWO

Remove the existing (2) bolts from the gas tank support.
Attach the control valve assembly to the side of the upright using (2) 3/8 X 1” carriage bolts provided with the kit and reuse the nuts that were removed.

NOTE

If your machine is equipped with an “all liquid” tank and is the Steel Green current design (pictured below). You can move the valve assembly to the other side of the upright.
If your machine is equipped with the old valve design, you can purchase the updated brackets.

NOTE: Before starting the following steps, drain the hydraulic oil from the machine. Refer to Steel Green Hydraulic oil change manual.

WARNING!
Connecting the hoses incorrectly will blow the seals out of the snow plow valve & void the Steel Green Warranty.

STEP THREE

Locate the hose that runs from the bottom port of the hopper control valve down to the left pump.
Disconnect each end of the hose and use the (2) 1/4” jic red plugs provided with the kit to cap the ends of the hose.

NOTE: Leave the hose zip tied in the bundle and tuck the ends out of the way.

TIP: Disconnect the end from the hopper control valve first and hold the end of the hose up to prevent excess oil spillage. Then turn the end down into a container to drain the rest of the excess oil. Have a rag and or container ready to catch excess oil.

NOTE: If your machine is equipped with a Hill Side Assist system, Proceed

STEP FOUR

Using (1) of the 38” hoses provided with the kit, attach the end with the straight fitting to the return port of the control valve.
Attach the other end of the hose to the input port of the hopper control valve. (end with 90° fitting)

STEP FIVE

Using the other 38” hose provided with the kit, attach the end with the straight fitting to the supply port of the control valve.
Attach the other end of the hose to the hydraulic pump. (end with 90° fitting)

NOTE

Some parts not shown for clarity.
Before starting the following steps, remove the supply hose from the Hill Side Assist system. Refer to the Steel Green HSA manual.

STEP FOUR: (HSA)

Using a 38” hose provided with the kit, attach the end with the 90 ̊ fitting to the tee fitting hydraulic control valve.
Attach the other end of the hose to the inlet port on the plow control valve.

STEP FIVE: (HSA)

Using the other 38” hose provided with the kit, attach the straight end to the outlet port on the plow control valve.
Attach the other end to inlet port of the hsa valve.

STEP SIX

Attach the snow plow to the hitch using (1) 5/8” X 3” bolt and nut provided with the kit.

STEP SEVEN

Route the snow plow hoses under the lift cylinder, along the right side of the hopper, up over the battery and to the control valve.
Route the hoses from the plow hitch along the right side of the hopper, up through the opening in the hopper shield, and to the control valve.

NOTE: Zip tie both hose assemblies away from any moving parts to prevent damage.

Route the hoses from the plow hitch along the right side of the hopper, up through the opening in the hopper shield, and to the control valve.
NOTE: Zip tie both hose assemblies away from any moving parts to prevent damage.

Connect the hoses from the snow plow to left side (ANGLE) of the control valve.
Connect the hoses from the plow hitch to the right side (LIFT) of the control valve.

STEP EIGHT