H Koenig wbt300 Electrical Heating Table Instruction Manual

: June 5, 2024
: H Koenig

Table of Contents

Cautions
Preparation
Installation
Operations
Cleaning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction Manual

Electrical heating table

H Koenig wbt300 Electrical Heating Table - Qr Code

https://www.hkoenig.com/s/38803_306776_table-chauffante-electrique

Cautions

Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. CAUTION — Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
The heater must not be located immediately below a socket outlet.
Do not use this heater with a programmer, timer, or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
Do not place the unit close to the curtain and/or other flammable objects. Otherwise, there will be a danger of catching fire.
Do not cover the unit with anything during operation or a short time after it’s shut down.
Do not wrap the power supply cord on the unit.
Do not use this unit in a place where causticity or volatile air exists, i.e. dust, steam, gas, etc.
Do not use this unit as a cloth drier or towel drier.
Do not use this unit as a sauna heater.
Do not use this unit as a room heater for heat-storing.
Do not use this unit in place of animal propagating and raising.
Do not use this unit in the heating system of the hot air center.
Do not immerse this unit into the water for cleaning.
The unit must be placed with a clearance of 150cm at least to the wall.
The unit must be securely placed on a horizontal and flat surface.
The unit is at a high temperature during operation. It keeps hot for a period after shut down. The potential danger would occur when touching it during this period.
The unit must be handled with care, and avoid vibration or hitting.
The unit must be securely grounded during operation.
When damaged, the unit must be repaired by a professional repairing team.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
When assembling, keep clear from any board or flammable material.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
The unit is for outdoor use only. It’s not allowed to use in building sites, greenhouses, barns,s or stables where there’s flammable dust.
The head of the unit is at a high temperature during operation. Unplug the unit and wait till it’s cool before cleaning.
The unit should be plugged into a socket, which is easily visible and reachable.

Preparation

Unpack the carton. Take out the accessories pack from the carton of the heater body. Make sure the accessories listed in the above Accessories Check List are included. If anything is missing, ask the retailer immediately to provide it to you.
Prepare a cross-head screwdriver.
Read this instruction manual carefully before installation and use. Keep this instruction manual in a proper and safe place for future use in case needed.

Installation

Take out all the components from the cartons.
As shown in figure A, turn over the Base and Base Cover, and let Screw M6*12(#7) fix the Wheels(#5) through the small holes on the Base.
Fix Screw Feet M6*30(#1) onto the Screw Board(#16), and adjust it to the same level as the Wheels.
Put Spring Washer ø8.5(#23) and Spring Washer ø8.2ø16(#24) into the Screw M8120(#4) then get through the Base(#6), Base Cover(#9), S/S Tube(#10). Use the provided Allen Key M8 to fasten the Screw M8*120（#4）with Foot Bracket.
Turn over the Heater Body. Put the Base on it. Pull out the Power Cord（#14） through the Base Cover（#9） and Base（#6）.
Let the Base Brackets（#8） match with the holes on the Base Cover(#9)and Base(#6). Then fix the Base Brackets with the Washers(#3) and Screw M6*20 (#2) with the provided Allen Key M6.
Fix the Power Cord with the Cord Clip(#15).
Put the Table Top on top of the Heater Body. Make sure the screw holes on the Table Fixture are matching the holes on Top Steel Board. Fix Table Top onto Heater Body with 4 Screws M6*8 (#20) and Spring Washers ø6.2(#11)

Operations

Plugin the unit into a socket. Make sure the power supply is the same as rated.
Press Switch(#30) to switch on the power. The heater is shifted to Standby mode. The power Indicator Light starts flashing.
Press the “MODE” button on the control panel or on the remote controller to switch on or to shift it to a different power of the heater, Low (Green Light), High (Red light).
Press the “OFF” button to shift the heater to standby mode. The indicator light starts flashing again.
Press Switch(#30) again to cut off the power totally in case the heater is not to be used for a long time.

WARNING:
This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.

Cleaning

Unplug the unit before cleaning. It should be wiped with a wet cloth. Do not use too much water.

Accessories Pack Check List:

Accessory Name| Qty| Accessory Name|

Qty

No.

| Part Name| No| Part Name| No.|

Part Name

1| Screw Foot| 11| Spring| 21| Power Indicator Light
2| Screw M620| 12| Foot Bracket| 22| Control Panel
3| Washer| 13| Heater Body| 23| Spring Washer ø8.5
4| Screw| 14| Power Cord| 24| Spring Washer ø8.2ø16
5| Wheel| 15| Cord Clip| 25| OFF Button
6| Base| 16| Screw Board| 26| Receiver
7| Screw M612| 17| Table Top| 27| Mode Button
8| Base| 18| Table Fixture| 28| Remote Controller
9| Base Cover| 19| Top Steel| 29| Switch
10| S/S Tube| 20| Screw M68| |
Disposal of appliances and batteries

| After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies:

Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, reusing the materials, or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

Adeva SAS/H.Koenig Europe – 8 rue Marc Seguin, 77290 Mitry-Mory, France www.hkoenig.com – sav@hkoenig.com – contact@hkoenig.com – Tél: +33 1 64 67 00 05

Points de collecte sure www.quefairdechets.fr