Camco Mfg T10116 Anchor Winch Wireless Remote Control Kit Instruction Manual
- June 5, 2024
- Camco Mfg
Table of Contents
INSTALLATION INSTRUCTIONS
ANCHOR WINCH WIRELESS REMOTE CONTROL KIT
T10116
For use with the TRAC® Anchor Winch Models: Fisherman 25® and Pontoon 35®
Push-button Anchor Winch operation from any location, in addition to the
switch on the winch housing.
UNPACKING
When unpacking, ensure that all parts are present and inspect for any damage
that may have occurred during transit.
KIT INCLUDES
- Control Unit (CU)
- Handheld Wireless Remote with bracket and 2 screws
- Shrink Tube, 2 pcs
- 4 Plastic Cable Ties (used for older winch models without control unit mounting plate)
INSTALLATION INSTRUCTIONS
-
Remove the cover, and disconnect the switch, motor and battery connectors. Remove the existing Control Unit (CU) from the winch frame. To disconnect the battery wires, first, remove the shrink tube. Cut with a utility knife. DO NOT cut fingers! Be careful.
-
Install the Wireless Control Unit (CU) using the holes or slots that match the bolt pattern. (No drilling required.) Install Wireless CU with existing screws from the standard CU that was removed.
NOTE: In older models without a CU mounting plate, place a cable tie through each of the four holes located on the Wireless CU. Loop two cable ties, loosely but evenly, around the lower bar FIRST, then loop the last two around the upper bar and tighten all cable ties. -
Place a shrink tube over each battery wire before making the connection. After the connection is made, slide the shrink tube over the metal connectors. Heat the shrink tube with a hot air gun, or another heat source. The tubing will shrink down to the wires and seal the connection.
-
Connect the winch motor to the CU. Connect the switch to the CU
-
Replace the cover.
RE-PROGRAMMING INSTRUCTIONS
NOTE: The remote is pre-programmed to the CU at the factory and does not need to be programmed when purchased. These instructions are for future reference should you need them.
- Press ON and DOWN on the remote within 2 seconds after connecting the winch to the battery.
- Hold 5 seconds then release the ON and DOWN buttons.
- Re-programming is done.
Please note, the timing is critical to press and hold the ON and DOWN buttons within 2 SECONDS after connecting the winch to the battery or the re- programming will not work.
FREQUENTLY ASKED QUESTIONS
Q: Can I control two anchor winches with one remote?
A: No each wireless remote can only control one anchor winch.
Q: Do I need to program the remote when I install it?
A: No the remote is preprogrammed at the factory to this Control Unit.
TRAC Limited Warranty
This limited warranty is provided by TRAC Outdoor Products Co (TRAC) to the
original consumer purchaser (purchaser) of this TRAC product. This limited
warranty is not transferable to any other party. TRAC will at its option
repair or replace any part(s) of the TRAC product which may be found by TRAC
to be defective within two (2) years of purchase. TRAC will pay the shipping
charge to the purchaser for any part(s) which may be shipped by TRAC. For
warranty repair or replacement, the purchaser must provide dated proof of
purchase and notify TRAC of the request for warranty service. The purchaser
will notify TRAC by email at [email protected] or
by phone at 615-462-6224 for warranty
service. TRAC will attempt to provide the parts needed. If the product is to
be returned, the purchaser will be provided a Return Goods Authorization (RGA)
number to include with any return for warranty service which will be shipped
at the purchaser’s expense to the address provided. The purchaser must use
reasonable care in the maintenance and operation of the product in accordance
with this manual. Failure to follow the instructions in the manual will void
the warranty. This warranty covers defects in the material or workmanship of
the TRAC product. This warranty does not cover failure that results from
misuse, improper installation, accident, abuse, neglect, modification, or
improper maintenance. There is no other express warranty. Implied warranties,
including those of merchantability and fitness for a particular purpose, are
limited to two (2) years from the date of purchase. Costs of installation or
repair by service centers or marine repair facilities are not covered by this
warranty. This is the exclusive remedy and any liability for any and all
incidental or consequential damages or expenses whatsoever is excluded. Some
states do not allow limitations on how long an implied warranty lasts, or do
not allow exclusion or limitation of incidental or consequential damages, the
above limitations may not apply to you. This limited warranty gives you
specific legal rights, and you may also have other rights which vary from
state to state.
TRAC Outdoor Products Company 251A
Mayfield Drive Smyrna, TN 37167
www.trac-outdoor.com
[email protected]
615/462-6224
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment