BOOMERINGAU HSFC6860 Basketball Hoop Instruction Manual

Copyright 2023
BOOMERING BAFC-6872 BASKETBALL HOOP
Installation & Owner’s Instructions

HSFC6860 Basketball Hoop

Add:47 Berriman Drive, Wangara
Phone: 1300 499 311
Web: www.boomering.com.au
WARNING
FAILURE TO COMPLY WITH ANY OF THE WARNINGS IN THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY.
FAILURE TO COMPLY MAY ALSO RESULT IN PROPERTY DAMAGE. PLEASE HEED ALL WARNINGS AND CAUTIONS TO ENSURE YOUR SAFETY
DO NOTE ATTEMPT TO ASSEMBLE WITH SYSTEM WITHOUT CAREFULL READING AND UNDERSTANDING THE INSTRUCTION MANUAL FIRST
Keep this instruction manual in case you have to contact the manufacturer for replacement parts.

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
FAILURE TO DO THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly.

• Ifusea ladder during assembly, use extreme caution.
• 4 people are recommended for this operation.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play.
• Before digging, contact utility company to locate underground power cables, gas and water lines. Ensure there are no overhead power lines within 20 ft. (7m) radius of pole location.
• Climate, corrosion or misuse could result in system faiiure.
• If technical assistance is required, contact us:

WARNING
FAILURE TO DO THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow these rules for safe operation of the system.

• Only hang from the rim briefly to regain balance or avoid injuring others. Release the rim as soon as possible safely.
• During play, especially when performing dunk type activities, keep palyer’s face away from the backboard, and net. Serious injury could occur if teeth/face come in contact with backboard, rim, or net.
• Donotslide, climb, or play on pole.
• When adjusting height, keep hands and fingers away from moving parts.
• Donot allow children to adjust system.
• During play, do not wear jewelry (rings, watches, necklaces, ets.) Objects may entangle in net.
• Keep water and organic material away from pole. Pole can rust and fail.
• Check pote and all metal parts regularly for rust. completely remove rust and repaint with exterior enamel. if rust has penetrated any steel parts, replace that part immediately.
• Check system before each use for loose hardware, signs of rust and instability. Repair before each use. Never play on damaged equipment.
• Wear a mouthguard when playing to avoid dental injuries.

EXPLODED VIEW

PARTS LIST

ITEM| QTY| DESCRIPTION
A| 1| Main Post
B| 1| Actuator
C| 1| Spring-Assist Cartridge
D| 1| Pole&Gusset padding
E| 1| Main Extension Arm
F| 2| Upper Extension Arm
G| 1| Backboard
H| 1| Rim Height Sticker
UNDERGROUND PARTS
U1| 1| Anchor Template
U2| 4| 16mm Anchor J-bolts
U3| 8| Thick washer for J-bolt
U4| 12| Hex nut M16
U5| 4| Anchor Rebar 36″L
U6| 4| Lock Washer M18
RIM HARDWARE
R1| 4| Hex bolt fV110x60
R2| 8| Flat Washer M10
R3| 4| Lock Washer M10
R4| 4| Hex nut M10
HARDWARE LIST

ITEM| QTY| DESCRIPTION
1| 6| Nylon Washer M18
2| 2| Nylon Washer M14
3| 4| Hex Bolt M18x335mm
4| 2| Hex Bolt M18x280mm
5| 2| Hex Bolt M18x140mm
6| 2| Hex Bolt M14x4Omm
7| 14| Washer for M18 Bolt
8| 4| Washer for M14 Bolt
9| 8| Lock Nut M18
10| 4| Lock Nut M14

INSTALLATION

(Day 1 to Day 4)
Prior to anchor system and goal assembly, call utility services for location of underground utility lines before you dig.
This assembly needs 5 days totally.
Day 1: Anchor system installation.
Day 2-4: Allow concrete to cure.
Day 5: Complete basketball system installation.

SIX PEOPLE IS NEEDED TO LIFT UNIT INTO PLACE

Tools and materials required for assembly

1. TwoAdjustabie Wrenches
2. 1-1/8″ Wrench
3. 9/16″ Wrench
4. 3/4″ Wrench
5. 11/16″ wrench
6. 1″ Wrench
7. Hammer or Mallet
8. Tape measure
9. Shovel
10. Concrete 16 Bags (80Ibs/bag).
11. Electric Drill
12. Carpenter’s Level
13. Aminimum of two Ladders
14. Water Supply

Day 1: Anchor system installation.
One adult is needed for this step.

1. Locate your system close to or on the court, referring to your goal specifications in Figure 1. WARNING
   Before digging hole for anchor system, check for buried power, gas, water, and telecommunication lines! Failure to do so could result in serious or fatal injury! Contact your local utility company if unsure. Regulation Court Lengths
   High school: 84′
   College & Professional: 94′
   Day 1: Anchor system installation.
   

2. Assemble anchor system as shown in Figure 2.
   Thread nut M16(U4) all the way to bottom of threads on J-bolt (U2) insert threads of J-bolt through hole on anchor plate (U1) and secure with nut (U4).
   Note: Please follow the leg direction of J bolts shown in Figure 2 .

3. Dig hole 52″ deep and 21” in diameter using a spade, shovel. or post hole digger. Warning
   Never continue to assemble your system without following cementing instructions. Failure to do so may cause serious personal injury or property damage.

4. Mix and pour concrete into hole. Follow instructions on concrete bag. Stop about 18” below playing surface.

5. Insert 6 Rebars (U5) into concrete 8″ apart making a square in center on hole.

6. Continue to pour concrete into hole. Use a concrete form or wooden form for top 4″, until concrete flush with playing surface (can be 2-4inch higher than play court if needed).

7. Push anchor system into concrete and agitate to eliminate voids in concrete.

Level and square anchor plate (U1) to playing surface. This is very important!
Clean off any concrete on anchor plate and exposed threads.
You are finished with anchor system.
Allow concrete cure a minimum of 72hrs.
Day 2-4: Allow concrete to cure

• Allow 72 hours for concrete to cure before continue to installation.
• Check to see that no Concrete or Debris obstructs threads on threads of J bolts.

To be continued.
INSTALLATION (Day5)
Ahammer or mallet may be needed during assembly.
A. Slide a 16mm Thick Washer (U3) over each of the J-Bolts (U2) as shown in FIGURE 1A.
B. Remove the Padding from Main Post (A). Place the Main Post (A) over the J-Bolts. Slide a 16mm Thick Washer (U3), a Lock washer 16mm (U6) and thread a 16mm Hex Nut (U4) to each J-bolt. Tighten the Nuts only a few turns onto the J-Bolts as shown in FIGURE 1B.
C. If the Main Post (A) is not exactly vertical, adjust the 16mm J-Bolt Hex Nuts (U4) located under the Post base. Tighten ali of the Hex Nuts (U4) Above Post base when Main Post (A) is vertical.
NOTE: Face the Main Post (A) with Actuator Bracket facing playing court (as shown in FIGURE 1C).

STEP 2
Attach Lower Extension arm (E) to Pote (A).
Slide the Main Extension Arm(E) over the top of the Main Post (A) , attach Main extension arm (E) to the lower pivot tube in Pole (A) with one Hex bolt M18x335mm (#3), two Flat Washers M18(#7).four Nylon Washers M18 (#1), and one Nylon nut M18(#9).
Note: Nylon washer has been pre-installed in the factory.

INSTALLATION (Day5)
STEP 3
Attach the Spring-Assist (C) to Main Post (A) with one Hex Bolt M18x140mm (#5), two Flat Washers M18(#7) and one Lock nut M18 (#9).

STEP 4
Raise Main extension arm (E) to align the second set pivot tubes in Pole (A) with holes at the bottom of Spring assist Cartridge(C). Slide one Flat washer M18 ( #7) over Hex bolt M16x320mm (#3), and slide the bolt all the way thru Main extension arm (E), Spring-assist Cartridges, secure it with one Flat Washer M18 (#7) and one Lock Nut M16 (#14) from the other side.
STEP 5
Attach the Spring-Assist (C) to Main Post (A) with one Hex Bolt M18x140mm (#5), two Flat Washers M18(#7) and one Lock nut M18 (#9).

STEP 6
Crank the Actuator (B) to align the bottom pivot tube with the third set of welded tubes on the Main Extension Arm (E), attach Actuator to Main extension arm Using one Hex bolt M18X335MM (#3), two Flat WashersM18 (#7), one Lock nutM18(#9)
STEP 7
Attach the 2 Upper Extension Arms(F) to Main Post (A)with one Hex Bolt M18x280mm (#4), two Flat Washers M18(#7), 2 Nylon washers (#1), and one Lock nut M18 (#9). Do not tighten at this time.

STEP 8
A. Hook Crank Handle to the hole in the bottom of actuator, crank to release Spreader bracket on Spring Assist Cartridge (C) and get them removed. See Figure STEP 3 onpage 7.
Attach the Backboard to Main Extension Arm(E) by using a Hex Bolt m18x335mm (#3), two Flat Washers M18 (#7), two Nylon washers (#1), and one Lock nut M18 (#9).

Note: Nylon washers go between Main extension arm Bracket (E) and Backboard mounting bracket.
B. Connect Upper Extension Arms (F) to the side of Backboard (G), using 2 Hex bolts M14x40mm (#6), 4 Flat Washers M14 (#8), 2 Nylon washers M14 (#2), and 2 Lock nuts M14(#10).
Note: Put Nylon washers between backboard plate and Upper extension connecting plate.
STEP 9
A. Remove the screws on Rim spring box cover, open the Spring box.
B. Crank lower backboard as much as possible.
Mount the rim to the Mounting bracket on
Backboard(G), using the hardware supplied in rim box.
C. Re-attach Spring box cover to the Rim with removed screws.
NOTE: Use alevel to adjust and make sure rim is level side to side before tightening nuts.

STEP 10
A. Apply Rim Height Sticker
After everything is square, make sure all nuts on the system have been tightened.
NOTE: Do not over tighten the Nuts, make sure the unit can be adjusted up and down.
B. To apply the Rim Height Sticker(In the manual pack), first use a tape measure to crank rim up to exactly 10’ from the playing surface. Use a pencil to make a mark on the Actuator(B) where the black plastic sleeve stops.
Then, peel and apply Rim Height Sticker to outside of Actuator(B) lining up the pencil mark with the 10’ mark on the Rim Height Sticker. See detailA.
C. Attach Post Pad and Gusset Pad to Main Post (A) (not shown).

Add: 47 Berriman Drive, Wangara
Phone: 1300 499 311
Web:www.boomering.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>