Streamline PR16002-AS Electric Hose Reel Controller User Guide
- June 5, 2024
- Streamline
Table of Contents
**Streamline PR16002-AS Electric Hose Reel Controller User Guide
**
Safety Instructions
Follow these instructions carefully to ensure safe operation of this unit
- Appropriate Personal Protection Equipment must be worn when operating this unit, eg goggles and gloves.
- Warning cones or signs must be used to alert the public to potential danger.
- If the push button operator cannot see the far end of the hose, then another operator must be present to keep an eye on the hose as it rewinds.
- Release the push button control immediately if the hose snags or the reel stops.
- Release the push button control immediately if the hose presents a danger to any person or animal.
- Do not exceed the maximum safe speed of operation.
- Do not override or change the factory settings.
- The reel rewinder unit must be serviced every 12 months.
Do not set the speed of the reel rewind higher than you are comfortable with using Specification| Value
---|---
Supply Voltage| 11 – 15 VDC
Maximum Current| 40A (Fuse @ 30A)
Typical Drive Current| 20-35A
Voltmeter Accuracy| +- 100mV
Water Resistance & material| IP65, ABS
Dimensions| 171 x 120 x 55(mm)
Working Temperature| 0 to 40 Deg C
Your battery is at risk of permanent damage if you disable low battery cutoff and continue to use your controller for long periods when the battery voltage has fallen below +10.SV
DISCLAIMER
THE MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES TO ANY PROOUCT HEREIN TO IMPROVE RELIABILITY, FUNCTION OR OESIGN. THE MANUFACTURER OOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PROOUCT OR CIRCUIT OESCRIBEO HEREIN.
Wiring
Your Reelmaster should come pre-wired. However if not for any reason connect
the reel controller following this diagram. NOTE only fit the fuse once all
connections are made.
WARNING
Make sure correct fuse is fitted inline. Failure to do so will result in
damage to the unit. Observe correct battery polarity. Failure to do so will
result in damage to the unit.
Power Up
Check that it is safe to rewind your hose and that it is free from obstructions and presents no danger to others. Read the safety instructions and follow them carefully ..
Turn on the controller by applying power and if necessary press and hold either the up or down button.
The value on the display indicates the speed of reel rewind from 0-99, where 99 is the maximum speed. Set to a speed that you are comfortable with using up and down buttons e.g. 70
For your safety a maximum speed of 60 is recommended.
To start the reel rewind press the enable push button on the flying lead. Observe all safety instructions. You may need to guide the hose onto the reel carefully.
To stop the reel release the push button.
- Appropriate Personal Protection Equipment must be worn when operating this unit, eg goggles and gloves.
- Warning cones or signs must be used to alert the public to potential danger.
- If the push button operator cannot see the far end of the hose, then another operator must be present to keep an eye on the hose as it rewinds.
- Release the push button control immediately if the hose snags or the reel stops.
- Release the push button control immediately if the hose presents a danger to any person or animal.
- Do not exceed the maximum safe speed of operation
Use
Press up or down to set a suitable rewind speed.
Press enter to display the current battery voltage.
Press enter again to return to the current rewind speed.
To turn the controller off, press and hold enter.
Controller Messages
| Message | Description |
|---|---|
| An over current situation has occurred, most likely because the hose has |
been snagged. The reel has been stopped for safety reasons. Remove the
obstruction, then press the push button to restart
| An obstruction has· been detected during a rewind. The reel has been stopped
for safety reasons, release the operator push button. Remove the obstruction,
then press the push button to restart.
| This message will start to flash when the battery is low (<11.0V). If
battery is below 10.SV the reel will be disabled to protect the battery.
(Unless low battery cutoff is disabled*)
STREAMLINE® Warranty
The warranty on all Machines and Equipment is for 1 year (12-months) from RECORDED DATE OF PURCHASE.
THIS WARRANTY EXCLUDES NORMAL MAINTENANCE ITEMS, including but not limited to HOSES, FILTERS, O-RINGS, DIAPHRAGMS, VALVES, GASKETS, CARBON BRUSHES and damage to motors and other components as a result of failure to replace normal maintenance items. THIS LIST IS NOT EXHAUSTIVE.
If STREAMLINE® receives notice of such defects during the warranty period, STREAMLINE® will either, at its opinion, repair or replace components which prove to be defective.
Replacement parts will only be supplied under warranty, upon the inspection and approval of the defective parts by STREAMLINE®.
Should it be necessary to supply replacement parts before the opportunity to inspect, these will be charged at current prices and credit will only be issued upon subsequent inspection and warranty approval by STREAMLINE®.
The customer is responsible for the cost of return of the defective part. If warranty is approved, STREAMLINE® will pay for the cost of the repaired or replacement part.
This warranty excludes the following conditions and circumstances which are at the discretion of STREAMLINE®:
Wear and tear, misuse, abuse improper maintenance, frost damage, the use of chemicals other than those supplied or approved by STREAMLINE®, improper installation or repair, unauthorised modification, incidental or consequential costs, loss or damage, service, labour or third party charges, the cost of returning defective parts to STREAMLINE®.
This warranty constitutes the exclusive remedy of any purchaser of a STREAMLINE® unit and is in lieu of all other warranties, express or implied, including without limitation any implied warranty of merchantability or fitness for use, to the fullest extent permitted by law. In no event shall any implied warranty of merchantability or fitness for use exceed the term of the applicable warranty stated above and STREAMLINE® shall have no other obligation or liability
Important
Unfortunately these rights cannot be transferred to a third party
Why STREAMLINE®?
Flexibility
- STREAMLINE® systems can be built according to customers’ exact requirements
- For non-standard systems, the user’s needs or specifications are listened to and turned into reality.
Quality
- Whilst price is important, quality is remembered long after price is forgotten
- We insist on sourcing brand name products from around the world, only of a reputable quality, and bring them together under the STREAMLINE® name
- All STREAMLINE® products carry a full one year’s warranty, according to the manufacturers’ standard terms and conditions of sale.
Service
- We have an in-house technical helpline able to answer most of your questions relating to the capabilities and functionalities of all STREAMLINE® products
- If we get it wrong, we will put it right. If you are sent a wrong item, we will immediately attend to sending you the correct item and arrange a collection of the wrong item without any quibbles
- STREAMLINE® is backed by a comprehensive range with massive stocks providing you with a ‘one stop shop’ for all your requirements.
MANUFACTURED IN THE UNITED KINGDOM
CHECKED AND TESTED BY QUALITY CONTROL
Hamilton House, 8 Fairfax Road, Heathfield Industrial Estate, Newton Abbot Devon, TQ12 6UD United Kingdom
Telephone: +44 (0) 1626 830 830
Email: sales@streamline.systems
Visit: www.streamline.systems
INSTR-PR1-CTRL-QS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>