IKEA 594.301.97 UPPSPEL Gaming Desk Instruction Manual
- June 5, 2024
- Ikea
Table of Contents
IKEA 594.301.97 UPPSPEL Gaming Desk
An electro-mechanically height-adjustable work surface with a control
interface to adjust the height up and down. This appliance can be used by
children aged 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning the use of the appliance in a safe
way and understand the hazards involved by a person responsible for their
safety.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Electrical sit and stand desk
Advice and instructions for UPPSPEL
Input:
220-240VAC, 50/60Hz
Standby power consumption:
<0.1 W.
Sound level:
Lower than 55 dB(A).
Height setting interval:
72-120 cm/28.3-47.2 inch.
Maximum load:
70kg/154lbs.
Temperature interval at usage:
+50 up to +104 °F/+10 °C up to + 40 °C.
Temperature interval at storage:
0 up to 158 °F/-18 °C up to 70 °C.
Humidity:
20% up to 80% at 104 °F/40 °C.
Power supply unit:
24.0V DC, 240 W.
This appliance shall only be used together with the included power supply
unit.
Every person who is responsible for this table at installation or employment
of the table in daily use or in service and repair work should carefully read
these instructions. Keep these instructions close to your sit/stand table.
Installation instructions
-
The table is assembled according to separate assembly instructions.
-
Connect the electrical cable to a power source.
NOTE! The electrical cable must have full mobility. -
The table is now ready for use. The motors stop automatically when the table reaches its lowest and highest position respectively.
Usage
- The table shall only be used as a gaming table with the possibility to continuously adjust the working height between sitting and standing positions.
- The table shall only be used indoors and in dry premises (office environment or similar).
The table must not be overloaded – the maximum load is 70KG/154lbs. The system may be run continuously for a maximum of 2 minutes. Afterwards, the motors must stand idle for approx. 18 minutes before they can be used again.
Follow these instructions when adjusting table height:
- Make sure no objects are in the way of the table.
- ‘In order to move the table up/down, press the up and down arrow buttons respectively.
- ‘The display switches off when not in use for about 10 seconds. Press any button to wake the controller up.
Safety regulations
-
When the table is moving up/down, keep the necessary safety distance to avoid the risk of being squeezed between the moving table top and fixed objects in the surrounding area.
-
When the table is moving up/down, the user shall make sure that nobody is injured and that no object is damaged. The table top must not bump into a fixed object, causing the table to overturn. Always remove any chair before the table is moved up/down.
-
The table tripod must not be altered or reconstructed in any way. In service and repair work of the table, the electrical cable must always be disconnected from the power source.
-
Modifications to the legs are absolutely forbidden!
-
The table must not be used as a hoisting device for persons.
Maintenance and repair instructions -
After approx. 1 week of use, check that the screws are properly tightened.
-
If the table cannot be lowered or raised, check that all electrical connections are connected properly.
-
If any part of the electrical system is replaced, the electrical cable must first be disconnected from the power source. Replace the electrical part and then connect the electrical cable to the power source. The table is now ready for use.
If the table still does not work, please contact your nearest IKEA store or customer service.
Manufacturer
IKEA of Sweden AB
Address:
Box 702, SE-343 81 ÄLMHULT
SAVE THESE INSTRUCTIONS
Product servicing
Do not attempt to repair this product yourself, since opening or removing
protective covers may expose you to dangerous voltage points or other risks.
Troubleshooting
NOTE!
Always disconnect the cable from the wall socket before maintenance!
| Symptom | Check | Try |
|---|---|---|
| The desk does not move. | Is the main power supply connected to the | |
| legs? | Try to connect a lamp or similar to the main power supply to |
check that the supply voltage is OK.
Are all plugs mounted correctly between the legs and power
supply?
| See assembly instructions. Check all connections.
Is there visible damage to the cables, controls or the legs?| Damaged parts
must be exchanged – Contact IKEA Customer
Service.
The desk stops and can only then move in the opposite direction.| Is the desk in its fully raised or lowered position?| When the desk has reached its upper position it can only move
downwards.
Is there a lot of weight on the desk compared to when the
desk functioned normally?
| Remove some of the load and try again.
The desk will only move downwards even though the desk is not
overloaded.| | Perform Basic settings.
The desk does not move up to its fully raised position. It always stops at
the same position.| | The system has a new end stop position upwards.
Perform Basic
settings to remove this stop.
The desk only moves a little bit upwards and stops.| Have the correct screws been used when mounting the
frame to the legs?
| Check if any screw used has the correct length (assembly
instruction). If the screw is too long it can damage the leg.
Are all connections correct?| Check all connections.
Does the desk have too much weight on it?| Reduce the weight load and try
again. A Basic setting might be
needed before the desk will move upwards.
The USB doesn’t work.| | Contact your nearest IKEA store or customer service.
Basic Setting
Push the arrow down button until the legs have reached the lowest position and keep pressure on the button for 6 seconds more. Upon certain errors, this must be done twice in succession. Now the desk is in the initial position.
Initialisation instructions:
Height Adjustment Controller
Reset process **
**
Error Code Instructions
| Error Code | Reason | Solution |
|---|---|---|
| E01 | Overcurrent protection/short circuit | See instructions for |
Reset/Initialisation.
E07| Motor line open-circuit error| See instructions for
Reset/Initialisation.
H01| Over-heating| Unplug from the wall socket and re-plug – or wait 18
minutes to let the
motors cool before using them again.
RST| Power failure| See instructions for Reset/Initialisation.
888/000| Controller error| Please contact IKEA Customer Service.
The crossed-out wheeled bin symbol indicates that the item should be disposed
of separately from household waste. The item should be handed in for recycling
in accordance with local environmental regulations for waste disposal. By
separating a marked item from household waste, you will help reduce the volume
of waste sent to incinerators or landfills and minimize any potential negative
impact on human health and the environment. For more information, please
contact your IKEA store.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>