2AWTTNTSECGW NewTech NT Secure Gateway Flexible Networking for Industrial Automation User Manual

2AWTTNTSECGW
NewTech NT
Secure Gateway Flexible Networking for Industrial Automation
User Manual

User Manual NT SecureGateway
Language Version:
Date: 2020-10
IMPORTANT NOTE READ CAREFULLY BEFORE USE TO BE KEPT FOR FUTURE REFERENCE
Valid for the following hardware components: NTSecureGateway 11648_0008_0012 V2.1

Change Management

Revision ID ……………………………..DV A1
Description of Changes………………… Initial Revision

Manufacturer

NewTec GmbH Buchenweg 3 89284 Pfaffenhofen Germany
Phone.: +49 7302 9611 – 0
Internet: www.newtec.de
E-Mail: info@newtec.de

General Notes

Copyright
Copyright © 2020 NewTec GmbH, Buchenweg 3, 89284 Pfaffenhofen, Germany
All rights reserved. The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and/or service NewTec GmbH manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of NewTec GmbH. Throughout this manual, trademarked names might be used. We state herein that we are using the names to the benefit of the trademark owner, with no intention of infringement.

Warranty

To the extent permissible by applicable law all information in this document is provided without warranty of any kind, whether expressed or implied, including but not limited to any implied warranty of satisfactory quality or fitness for a particular purpose, or of non-infringement of any third party’s rights. We try to keep this document accurate and up-to-date but we do not make any warranty or representation about such matters. In particular, we assume no liability or responsibility for any errors or omissions in this document. NewTec GmbH neither gives any guarantee nor accepts any liability whatsoever for consequential damages resulting from the use of this manual or its associated product. NewTec GmbH further reserves the right to alter the layout and/or design of the hardware without prior notification and accepts no liability for doing so.
External Documentation
We make no warranty about any other sites that are linked to or from this document, whether we authorize such links or not.

Liability

To the extent permissible by applicable law, in no circumstance, including (but not limited to) negligence, shall we be liable for your reliance on any information in this document, nor shall we be liable for any direct, incidental, special, consequential, indirect or punitive damages nor any loss of profit that results from the use of, or the inability to use, this document or any material on any site linked to this document even if we have been advised of the possibility of such damage. In no event shall our liability to you for all damages, losses, and causes of action whatsoever, whether in contract, tort (including but not limited to negligence), or otherwise exceed the amount, if any, paid by you to us for gaining access to this document.
Disclaimer
The information and specifications described in this manual are subject to change without notice.
Latest Manual Version
For the latest version of this manual, see the download page on our website at: https://www.newtec.de/
Technical Support
For technical support, e-mail: product-support@newtec.de
Licenses and Trademarks
Microsoft®, Windows®, and Windows 10® are registered trademarks of Microsoft Corporation. All trademarks and company names used are subject to the copyright of the respective companies.
Warnings Used in This Manual
Information marked with this symbol MUST be obeyed to avoid the risk of severe injury, health danger, or major destruction of the unit and its environment.
Information marked with this symbol MUST be obeyed to avoid the risk of possible injury, permanent damage, or malfunction of the unit.

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

Safety Instructions

This description is part of the device. It contains texts and illustrations for the correct handling of the module and must be read before installation or use.
Please follow the instructions in the description. Non-observance of the instructions, operation outside the intended use, incorrect installation, or incorrect handling can result in serious impairments to the safety of people and systems.
The device may only be installed, connected, put into operation, changed, or retrofitted by a qualified electrician.
Disconnect the device from the external power supply before carrying out any work on it. In the event of installation and system faults, the main potential may be connected to the control circuit for devices that are not electrically isolated. If necessary, also switch off independently supplied output load circuits.
For the installation of the device, the safety regulations of the electrical engineering and the employers’ liability insurance association must be observed.
Only the signals indicated in the technical documentation may be applied, and only components from the approved accessory components list of NewTec GmbH may be connected to the device’s connection terminals.
In case of malfunctions or ambiguities, please contact the manufacturer. Tampering with the device might seriously impair the safety of people and equipment. They are not permitted and will lead to exclusion of liability and warranty.
The proper and safe operation of the products requires proper transport, proper storage, set-up, assembly, installation, commissioning, operation and maintenance.
Any manipulation will void the warranty.

Intended Use

• This product is designed to be used in industrial applications.
• It is intended to be mounted in an electrical cabinet.
• It is intended to collect measurement data via the provided interfaces (Bluetooth Low Energy, CAN, RS485 or digital IOs) and provide this information to higher-level instances like PLCs, Industry PCs, or Cloud solutions.
• It is not intended to be used to control other devices, especially devices that can harm humans
• It is not intended to be used in safety-critical applications
• It is not intended to measure and/or transfer critical data that can lead to machine failures
• It is only intended to be used in an environment that is not exceeding the conditions defined in the chapter

Maximum Ratings.
The use of the product by private consumers is excluded. Buyer shall verify the suitability of the product for the intended application by own tests before using the NTSecureGateway. Due to a large number of parameters and conditions under which this product can be used, each organization and person using this product is obliged to test this product on their own responsibility for suitability and usability with regard to the desired application.

Residual Risks
The device must only be used for its intended purpose and only if it is in perfect safety condition.
Malfunctions that could impair safety must be rectified immediately.
In case of improper or unintended use, the device may no longer be used and any warranty claim expires.
Non-permissible influences can be: strong mechanical stress (e.g. when the device has been dropped), voltages, currents, and humidity outside the specification.
When commissioning machines/systems for the first time, all safety functions must always be checked in accordance with the applicable regulations and the specified test cycles for safety devices must be observed.
Designated Location of Operation
The device must only be used and operated in safe electrical cabinets. In any case, the regulations and provisions of the professional association and all provisions that apply at the respective operating site must be observed.

Device Overview

Key Features

• Microchip ATSAMA5D27 incl. 128 MB RAM
  o ARM Cortex-A5 core
  o Up to 500 MHz

• 4GB eMMC

• Interfaces:
  o 2xEthernet
  o Wifi
  o USB 2.0 Host
  o BLE
  o CAN
  o RS485
  o 4-20mA
  o 0-10V

• Supported protocols (additional Software license required):
  o OPC/UA
  o MQTT
  o PROFINET

• Housing: DIN Rail (72 x 90 mm)

• IP 67 housing available on request

• Power supply 7-32 V or passive POE (24 V)

Use Cases

• Secure data transfer
• End-to-end encryption
• Edge computing platform
• Extensible through individual application programming

Security Features

• Dedicated cryptographic hardware engine (ARM TrustZone)
• Cryptography and security middleware services·
• Secure Boot
• Secure Update
• Various supported encryption algorithms, such as AES, RSA, Diffie-Hellman, Elliptic Curve
• Tamper Protection
• ATECC608 Secure Keystore

Technical Data

Dimension

Maximum Ratings

Interfaces

For the Location of the interfaces see Figure 2: External Interfaces
Power Supply
Mating Connector: Phoenix Contact, Part No: 1836079

Pin Number

| Description
---|---
1| GND
2| 24V

Ethernet 1
10BASE-T and 100BASE-TX Ethernet connector Support for 24V passive Power over Ethernet (POE)
Ethernet 2
10BASE-T and 100BASE-TX Ethernet connector
CAN Bus / Digital Out
Depending on the mounting option this connector is used for CAN Bus or for digital output
CAN Bus:

Digital Output:

USB Host
USB-A connector for USB 2.0
RS 485/Analog
Depending on the mounting option, this connector is used for RS485, 4-20mA or 0-10V interface
RS485:

Analog Input:

User Button
Application dependent
Reset Button
System Reset
Status LED
RGB LED, application dependent
Wi-Fi Antenna Jack
SMA Antenna connector. Use specified antenna only: Pulse W1010
BLE Antenna Jack
SMA Antenna connector. Use specified antenna only: Pulse W1010

System Overview

General Description

The main functionality of these devices is to provide connectivity between different interfaces in a secure way. So there are a lot of communication interfaces that can be connected by software. The specific functionality depends on the software configuration of your application. For details please see the software user guide.
Block Diagram

Installation

Installation Requirements
The NTSecureGateway is designed to be mounted in an electric cabinet with a minimum protection class of IP54. It is intended to be mounted on a DIN Rail according to EN 60715 (35mm x 7.5mm). First snap in the orange clip at the top position (1) to the DIN Rail. Then pull down the orange clip at the bottom side (2) with a screwdriver, to also snap it to the DIN Rail. Ensure that both orange clips are in the default position and the housing is mounted firmly on the DIN Rail.

Initial commissioning
For initial commissioning connect 24 V to the power supply connector. The following connector is needed: Phoenix Contact, Part No: 1836079.
Ensure that the supply voltage is not exceeding the values defined in Table 1: Maximum Ratings, otherwise the device could be damaged.
Respect polarity, otherwise the device could be damaged.

NewTec GmbH
Buchenweg 3
89284 Pfaffenhofen a.d. Roth
Germany · Tel.: +49 7302 9611-0
product-support@newtec.de 
www.newtec.de

References

• NewTec GmbH
• NewTec GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>