Shenzhen Ruineng Technology B022 Smart Music LED Ceiling Light with Speaker Instruction Manual
- June 5, 2024
- Shenzhen Ruineng Technology
Table of Contents
Ruineng Technology B022 Smart Music LED Ceiling Light with Speaker
Instruction Manual
Bluetooth Connection
For the first time you use it or never pair it with “AnSLong” after moving the equipment, please have it paired according to the steps below.
Music Connection
Enter the System Settings Bluetooth – to discover and connect the device name
” AnSLong “, Once connected, you will hear the connection tone.
Installation Steps
Step 1: Screw off the hanging plate on the lamp
Step 2: Connect the household wire to the wire with the terminal (as the
single short wire shown in Figure 2 ), and pass the connected wire through the
hanging plate
Step 3: Perforated the cement ceiling and fixed the hanging plate on the
ceiling by three screws
Step 4: Connect the wire with the terminal to the wire on the lamp Step
5: Turn the lamp body clockwise to fix it on the hanging plate
Step 1: Lock the hanging plate on the lamp by one screw
Step 2: Connect the wire terminal in the socket (as the E27 socket shown in
Figure 2 ) to the wire terminal on the lamp
Step 3: Fix the socket to the lamp by three screws
Step 4: Install the socket to the household connector
Three-gear light modes via wall switch:
The First Gear: Switch on to daylight white (default light);
The Second Gear: Switch off and on after the first gear to go to the rhythm
mode which color change follows with music rhythm, brightness change follow
with volume;
The Third Gear: Switch off and on again after the second gear to go to seven
single colorful lights. (Press the wall switch once to change color) Note: The
light will be default white light after being switched off for 5 seconds
Specification
| NO. | Item | Parameter |
|---|---|---|
| Light | Item Weight(KG) | 0.54kq |
| Input Voltage(V) | 100-240V/S0-60HZ | |
| Input Power(W) | 18W | |
| Size(MM) | 0:280 H:60(mm) | |
| CRI | White >0.8 | |
| Luminous Flux 11.1 | 1600k-n | |
| Color Tempera ture(K) | 6300-6800 ,Tolerance: *250K | |
| light Decay | <10%,T=25C: RH=90: H=2000 | |
| Certificate On | CE PSE | |
| Waterproof Rating | P65 | |
| Audio | Audio Power(W) | 5W, 40, THO+N =10%, IKHz |
| Frequency Response | 40142-20KHZ. Nonuniformity:m3dBm | |
| Signal to Noise Ratio(SNR) | >80dBm P=IW: A-weight | |
| Volume Control | Bluetooth | |
| Eiluetooth Distance | <10m. Straight line distance and no obstacles |
Danger:
- Before installing, cut off the power supply to prevent electric shock .
- Do not install the lamp on a damp ceiling and wear gloves when installing .
- You do not need to pay attention to the phase when installing. All you have to do is connect the neutral conductor ( white ) and live conductor ( red ) to one power cable of the lamp with a luster terminal
- Our lights have no ground wire/earth (green/yellow). However, we have taken measures to protect the power supply in accordance with the CE certification standard. So do not worry about security issues .
- Our lamps are not dimmable, so no dimmer switches should be installed together with our lamps, otherwise, this would interfere with normal use.
Federal Communications Commission (FCC) Statement. This device complies with
part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will does not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly approved
by Shenzhen Ruineng Technology Ltd may void the FCC authorization to operate
this device.Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
RF exposure statement:
The transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter. This equipment complies with the FCC RF
radiation exposure limits set forth for an uncontrolled environment. The
installation and use of this product are not restricted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>