Shenoy Audio SH020 Active Noise Cancelling Headphone User Manual
- June 5, 2024
- Shenoy
Table of Contents
SH020 Active Noise Cancelling Headphone
User Manual
Use
Power on/off
To turn on headphone. press and held the Bluetooth button 151 until the Status
LED (4) blinks blue. Press and hold the Bluetooth button again until the
Status LED blinks red. The headphone is now turned off
ANC on/off
To start the noise cancellation. slide the ANC button (C up. The NC LED
(nearby the ANC button) will light uo in green. To turn off the noise
cancellation, slide the NC button down. The NC LED will turn off
Charging
Connect the Use Charging cable to the charging port(7) and a computer o, a
USE, power adapter. The LED wilt shine red cluing crating and turn off when
the battery Is fully charged. The LED will flash red if the battery level is
low. Note: when connected to a charging source, the Bluetooth function of the
headphone MI be shaped, but the ANC can work.
Pairing
Make sure the headphone is timed oft Press and hold the Bluetooth button(S)
for 5 seconds to enter pairing mode. The Status LED (6) will blink blue and
red. Turn on Bluetooth on your device and search for “Shenoy, select it when
found. If necessary, enter the passcode, “0000” to pair and connect the
headphone. Some devices also ask to confirm the headset connection after
pelting. The Status LEO will blink blue and a voice will say “connected” after
the pairing is successful. If no Bluetooth devices are paired within 3 minutes
the headphone will turn off.
Line-in
Turn off the Bluetooth and connect the headphone and device via the audio
cord. One end connects the device; the other end connect, the audio input
socket (2).
Note: You must turn the headphone off before connecting the cable if the Bluetooth mode has been activated. )(the battery is depleted, the noise cancellation most be turned off if you went to use the 3.5mm audio cable.
General functions
Change the volume with the + & – buttons (3 & 4). You can also skip to the nest track or go to the previous by holding the corresponding button. Play or pause the current track by pressing the Bluetooth button(5).
To answer or end a call. press the Bluetooth button(5). Press and hold It twat least 6 seconds to reject an incoming call. Double click it to redial the last call.
Overview
- ANC Switch
- 3.5mm Audio Socket
- Volume Up/Next Track
- Volume Down/Previous Track
- Bluetooth Function Button
- LED Indic for
- Charging racket
- Microphone
Specifications
| Bluetooth Version: | V5.0 |
|---|---|
| Driver Size: | 40mm |
| Impedance: | 32Ω |
| Sensitivity: | 96±3dB |
| Frequency Response: | 20 Hz – 20kHz |
| Working Distance: | Up to 10M |
| Cancellation Frequency Range: | 40 Hz-600 Hz |
| Cancellation Central Frequency: | 100 Hz-300 Hz |
| Cancellation Level : | 20 dB±2dB |
| Battery Capacity : | 3.7V,400mAh |
| Charge Input: | 5 V,200mA |
| Charge Time: | 2.5-3 Hours |
| Working Time: | Up to 15h (12h with ANC ON) |
| Charging Port: | Micro U5B |
| Charging Cable Length: | 50 cm |
| Detachable Audio Cable Length: | 1,0 m± 10% |
NOTE!
This product contains a rechargeable Li-ion battery and the battery can not be replaced.
To prevent possible hearing damage. do not listen at high volume levels for long periods.
Downloads
Shenoy Audio SH020 Active Noise Cancelling Headphone Manual – [Download PDF ]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>