VELOCIFIRE M87 Mac Layout Mechanical Keyboard User Manual
- June 5, 2024
- VELOCIFIRE
Table of Contents
VELOCIFIRE M87 Mac Layout Mechanical Keyboard
Specification
- Polling Rate:1000Hz
- Flash ROM: 64KB
- Voltage: VDD = 3.0V – 5.5V
- Temperature: – 40°C – + 85°C
- Package form: LQFP64
RGB Backlit Modes
- FN+Scroll: Adjust 19 LED-backlit modes
- FN+Pause: Adjust lighting color,9 levels
- FN+↑: Increase brightness
- FN+↓: Decrease brightness
- FN+→: Increase speed
- FN+←: Decrease speed
Gaming Interaction Mode
FN+DEL:
- First mode: FPS–WASD R←→↑↓ESC blocks light up
- Second mode: COD–QWERTASDFGCV1-7 Ctrl Shift blocks light up
- Third mode: Car-WASDR Ctrl Shift Alt ←→↑↓ blocks light up
- Fourth mode: LOL–QWER DGFBVCtrl Alt Tab~1-6 Es blocks light up
Note: The lighting of the 4 preset game modes can be recorded.
Recording steps
Set the individual keys first, then adjust to the color (red,orange yellow,
green, blue, purple,white, pink).
After entering any game mode, press FN+HOME to start recording, the key has no
output function at this time, the indicator light flashes, click the key to be
recorded, adjust the light color. To finish recording, press FN+HOME to finish
recording
Multimedia Function
- FN+F1:Home
- FN+F2:MyComputer
- FN+F3:Mail
- FN+F4:Music
- FN+F5:Previous Playlist
- FN+F6:Next Playlist
- FN+F7:Play/Pause
- FN+F8:Stop
- FN+F9:Mute
- FN+F10:Volume down
- FN+F11:Volume up
- FN+F12:Lock/Unlock the keyboard
- FN+Esc:Hold for 3 seconds to restore factory settings
- FN+WIN:WIN lock/unlock
- FN+W:WSADis interchanged with ↑↓←→click
- FN+W again to restore to normal
Package Contents
- 1xMechanical Rechargeable Keyboard
- 1xUSB Nano Receiver
- 1xType-CCable
- 1xUser Manual
- 1xKeycap Puller
- 1xSwitch Puller
Features
- Mechanical M87 keyboard
- 2.4G Wireless+ Wired dual modes
- Rechargeable battery:4000mA
- RGB backlit, 19 kinds of lighting modes
- USB Full Speed 2.0(12Mbps)
- N-key rollover
Installation, Connection and Use
-
Wired mode
Toggle the switch to the left (the color card shows red) for wired mode Connect the USB charging cable to your computer. -
2.4G Wireless mode
Charge the battery. Toggle the switch to the right (the color card shows green) for wireless mode. Plug the USB nano receiver into the USB port of your computer.
Once the computer recognizes the keyboard, you’re ready to use. In 2.4G Wireless mode, lf not use for more than 60 seconds, the RGB backlit will turn off automatically and the keyboard enters power-saving mode.lt is better to turn off the keyboard when not used for a long time.
Build the connection between the USB receiver and keyboard
Toggle the power switch to the right (the color card shows green), press FN+P
for 5 seconds, and now the key”P”is flashing. Plug the USB nano receiver into
the USB port of your computer. Key”P” stop flashing after building the
connection successfully.
Charge the keyboard
The battery should be charged for at least 6~8 hours before being used for the
first time. When the battery is low, the FN keyred light flashes.Connect the
USB charging cable to your computer or adapter.The charging indicator is
located on the left side of the space bar, the charging status lights up, and
it turns off when fully charged.(charging time: around 6~8 hours).
NOTE: If you want to use the keyboard when charging, you should choose
Wired mode,the power switch must be toggled to the right position.
Troubleshooting Tips
If you experience problems while using the keyboard, here are some helpful troubleshooting tips: Check the power switch is on the right and Check the battery is charged. Check the receiver is properly connected to the USB port. Try reducing the distance between the keyboard and the computer . Remove any large metal objects located between the keyboard and the computer that could interrupt the signal. Product pictures are for reference only.
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>