DELTACO GAMING DH420 Wireless RGB Gaming Headset Instruction Manual
- June 5, 2024
- DELTACO GAMING
Table of Contents
DELTACO GAMING DH420 Wireless RGB Gaming Headset
OVERVIEW
- Headset
- Power on/off button and LEDs on/off
- Equalizer button
- USB-C charge port
- Microphone mute button
- Volume adjustment wheel
- Microphone port
- Microphone
- USB receiver
- USB-A to USB-C charge cable
- 3.5 mm audio cable
On/off
Press and hold the power button for 2 seconds to power the headset on. Press
and hold for 4 seconds to power it off.
Microphone
The microphone is detachable.
Press the microphone mute button to turn it on or off. Insert the microphone
by matching the lock icon with the notch. Then turn the microphone
counterclockwise to lock it in place. To detach the microphone, turn it to
unlock it, and pull it out.
Volume
Use the volume wheel to adjust the volume.
LEDs
Short press the on/off button to change LED mode. Automatic mode (RGB) >
static red > static greenish blue > static purple > static yellow > static
teal > static white light off.
Equalizer
Press the equalizer button to change between modes: Hifi, bass, 3D. The
headset remembers last used mode after being turned off and turned on again.
Connect wirelessly
-
Connect the USB receiver to your computer or device.
-
Power the headset on.
-
The LED powers on to confirm power on status.
-
Pairing: Press and hold the power button for about 5 seconds to pair or re-pair.
If the headset has already been paired, then you skip the pairing step. It can also be used as a troubleshooting step. -
If the LEDs changes to automatic mode (RGB), then the connection was successful.
If the LEDs are flashing green, then the connection failed. If it failed, please try disconnecting and connecting again.It is possible to have 2 headsets connected to 1 USB receiver. But it is not possible to connect 2 USB receivers to 1 headset. In the settings of your computer or device, make sure you have set the audio output correctly. If you are also using the microphone, please set the audio input correctly. If you move out of range the headset will flash green. When you move in range again, the headset will automatically reconnect. If you disconnect the USB receiver, the headset will flash green. Flashing green = currently not paired.
Wired connection
- To use 3.5 mm connection, you need to first turn the headset off (if it was on).
- Use the including 3.5 mm audio cable to connect the headset to your device. The headset will activate wired mode automatically.
- When using the 3.5 mm connection, the LEDs and the equalizer will be temporally disabled.
Charging
- You can use the headset while it is charging.
- Connect the USB cable to the headset and a USB power adapter (5V/1A) to charge it. When the battery has less then 10% left, the headset will play a tone 5 times. The headset turns off
- automatically after 30 minutes
- of inactivity, and after 10 minutes if it has not been paired.
- Charging takes about 3 hours.
- Flashing red = Charging.
- Green = Fully charged.
Compatibility
- Compatibility: PC | Mac | PS5 | Xbox One (wired only) | Mobile (wired only)
- The microphone mute function is disabled while in wired mode (3.5 mm).
- The microphone mute function in wireless mode (USB receiver) is compatible with PC, PlayStation 4/5 and Mac.
Cleaning
- Clean the product by using a dry cloth.
Safety instructions
- Keep the product dry. Keep it away from all liquids. This product is not waterproof.
- Do not open up or try to repair the product by yourself.
- Keep the product and packaging out of reach of children to prevent accidents and choking hazards.
- Do not drop or expose to shock damage.
Warranty
Please, see www.deltaco.EU for warranty information.
Support
More product information can be found at
www.deltaco.eu. Contact us by e-mail:
help@deltaco.eu.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>