Suzhou Fukuda Laser Precision Instrument MW-93TX 3D Cross Line Laser User Manual
- June 4, 2024
- Suzhou Fukuda Laser Precision Instrument
Table of Contents
User Manual
HOW TO OPERATE THE UNIT
RIGHT SIDE: Pendulum Lock
The 3D Cross Line Laser is a precision instrument and should be treated with
care.
When not in use, the pendulum should always be in the Lock/OFF position
(figure 1),
To lock the pendulum allows the Cross Line Laser to better withstand vibration
and trauma incurred during transportation or if the unit is dropped.
Figure 1
**LEFT SIDE-Automatic Leveling
**
When the pendulum is unlocked/OFF (figure 2), the pendulum is free to automatically level, In order for the Cross Line Laser to automatically level, the base of the unit needs to be within 5°of level.
Figure 2
Keypad:
A. Pulse indicator
B. Pulse button
When the pulse is on, this indicator A will turn red, at this moment laser
line can be picked up by the laser receiver. Press this key B again to turn
off the pulse function and the light will be off.
C.Power indicators
The indicators can display four levels of power:
100%(4 LED on)-75%(3 LED on)-50%(2 LED on)-25%(1 LED on).
When there has only 1 LED on/25%, the laser needs to be charged.
The laser will be off when there has no LED on.
D. Line Selection
-Line Selection: By pressing the Line Selection Button on the keypad panel can make various changes/collocations of laser lines. The sequence of it is as below:
The laser will be switched on with an H laser.
Press Line Selection Button for one time, Both H & V1 laser will be on.
Press Line Selection Button two times, All the three laser lines including H,
V1 & V2 will be on simultaneously
Press Line Selection Button three times, and it will turn back to the first
sequence of the laser/H lights on.
E. Lock mode indicator:
When the laser is in the mode of Pendulum Lock(switch bar on the right side).
By pressing/holding the line selection button(D) for 3 seconds to activate
Lock Emitting mode. In this model, the lock indicator (E) will be on, to
indicate user the laser is in lock mode and out of accuracy.
AC/DC Socket:
The laser can be powered from main power directly when there has no battery
inside the laser or the lithium-ion battery goes flat, by using the
authenticated power adaptor which is come with the kit, to provide continuous
electricity to the laser.
Ps: When connecting the power adaptor with AC/DC socket, power from the
lithium-ion battery will be cut off automatically.
In the meanwhile, the power adaptor can charge the Li-ion battery during the
time it drives the laser.
When the laser is off and connects with the power adaptor, it can charge the
li-ion directly.
Diameter of AC/DC socket pin: 2.5mm.
Power adaptor & battery system:
Lithium batteries can be charged when the laser is off. By simply keeping the
battery in the battery compartment and having a laser connects with a power
adaptor. The power adaptor will charge the laser automatically. During the
charge, the power indicators(C) will be on to indicate how much power has been
charged.
When there has no li-ion battery inside the laser, connecting the laser with a
power adaptor, can provide continuous electricity to the laser.
The alkaline battery pack is also compatible with this new battery system.
Simply replacing the Li-ion battery with a battery pack comes with 4 x
alkaline batteries. It can provide continuous working to laser as well.
Output Voltage:12V.
Input current: 2A.
Time to full charge the battery:3-4hours.
Protective voltage:8.4V
Battery capacity: 2600mAh.
Benefit Feature:
Lock & Emitting:
When our 3D laser is in the mode of Pendulum Lock(switch bar on the right
side).
By pressing/holding the line selection button(D) for 3 seconds to activate
Lock Emitting mode. At this model, the lock indicator (E) will be on.
The line will come out from the laser but be aware at this mode the laser
itself is out of accuracy as the pendulum is locked.
Laser at this moment can be used for some “special” applications such as
stairs alignment since the pendulum is locking.
Line alarm when in Lock Emitting mode:
The laser line will flash every 5 seconds to notice the user that the laser is
out of accuracy.
Alarm Functions
Out Level Alarm:
When the pendulum is unlocked and the Cross Line Laser is within 3°of level,
the unit will be in automatic leveling range, in this situation no LED light
will be on.
When the base of the unit locates outside the 3°leveling range the laser beam
will flash meanwhile an audibly warning will be sent out from Cross Line
Laser.
Specification:
| Accuracy | ±3mm/10m |
|---|---|
| Leveling Range | ±4° |
| Working Range/With Detector | 15m(Indoor) and 60m c/w detector |
| Tripod Thread | 1/4″ & 5/8” |
| Laser Type | Red:635nm Green:515nm |
| Operating Temperature | -10℃ to 50℃ |
| Storage Temperature | -20℃ to 60℃ |
| Dimension | 150 x 87 x 128/mm3 |
| Continuous Working Time | ≥ 8 hours (All Green diodes on) ＞ 15hour(All Red |
Diode on)
Power system| 15hour(All Red Diode on) Li-ion battery 2600mah, 7.4V & 4 x
Alkaline battery pack & Power adaptor
Net Weight| 0.8kg
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>