metabo BS, SB Series Cordless Drill Driver Instruction Manual

BS 14.4 LT

BS 14.4 LT Quick
BS 18 LT
BS 18 LT Quick
SB 18 LT

www.metabo.com

A

14,4 V…1,5 Ah …6.25498 … Li-Power Compact
14,4 V…3,0 Ah …6.25454 … Li-Power Extreme
14,4 V…4,0 Ah …6.25526 … Li-Power Extreme etc.

18 V…1,5 Ah …6.25499 … Li-Power Compact
18 V…3,0 Ah …6.25455 … Li-Power Extreme
18 V…4,0 Ah …6.25527 … Li-Power Extreme
18 V…5,2 Ah …6.25587 … Li-Power Extreme etc.

M

2) 2014/30/EU, 2006/42/EC, 2011/65/EU
3) EN 60745-1:2009+A11:2010, EN 60745-2-1:2010, EN 60745-2-2:2010, EN 50581:2012

2018-02-01, Bernd Fleischmann
Direktor Produktentstehung & Qualität (Vice President Product Engineering & Quality)
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany

1.

Original instructions

1. Declaration of Conformity

On our own responsibility, we hereby declare that these battery-powered drilling screwdrivers and impact drills, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards 3). Technical documents at 4) Fig. M.

2. Specified Use

The drills and impact drills are suitable for drilling in metal, wood, plastic and similar materials, and also for screwdriving and thread tapping.

The impact drills are also suited for drilling in masonry, brickwork and stone.

The user bears sole responsibility for any damage caused by improper use.

Generally accepted accident prevention regulations and the enclosed safety information must be observed.

3. General safety instructions

For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol!

WARNING – ­ Reading the operating instructions will reduce the risk of injury.
WARNING Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury.

Keep all safety instructions and information for future reference.
Pass on your electrical tool only together with these documents.

4. Special Safety Instructions

Wear ear protectors with impact drills (machines with the designation SB). Exposure to noise can cause hearing loss.

Hold tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. If the cutting accessory contacts a “live” wire, exposed metal parts of the electrical tool may become “live” and give the operator an electric shock.

Ensure that the spot where you wish to work is free of power cables, gas lines or water pipes (e.g. by using a metal detector).
Protect battery packs from water and moisture!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from defective li-ion battery packs!
If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out and comes into contact with your eyes, wash them with clean water and seek medical attention immediately.

If the machine is defective, remove the battery pack from the machine.

Remove the battery pack from the machine before any adjustments, conversions or servicing are performed.

Before fitting the battery pack, make sure that the machine is switched off.

Keep hands away from the rotating tool!

Remove chips and similar material only with the machine at a standstill.

Secure the workpiece to prevent slipping or rotation (e.g. by securing with screw clamps).

LED lights (11): Do not observe the LED radiation directly with optical instruments.

Reducing dust exposure:
WARNING – Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
– Lead from lead-based paints,
– Crystalline silica from bricks and cement and other masonry products, and
– Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

This also applies to dust from other materials such as some timber types (like oak or beech dust), metals, asbestos. Other known diseases are e.g. allergic reactions, respiratory diseases. Do not let dust enter the body.

Observe the relevant guidelines and national regulations for your material, staff, application and place of application (e.g. occupational health and safety regulations, disposal).

Collect the particles generated at the source, avoid deposits in the surrounding area.

Use suitable accessories for special work. In this way, fewer particles enter the environment in an uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:
– do not direct the escaping particles and the exhaust air stream at yourself or nearby persons or on dust deposits,
– use an extraction unit and/or air purifiers,
– ensure good ventilation of the workplace and keep clean using a vacuum cleaner. Sweeping or blowing stirs up dust.
– Vacuum or wash the protective clothing. Do not blow, beat or brush.

Transport of li-ion battery packs:

The shipping of li-ion battery pack is subject to laws related to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently valid specifications when shipping li-ion battery packs. If necessary, consult your freight forwarder. Certified packaging is available from Metabo.

Only send the battery pack if the housing is intact and no fluid is leaking. Remove the battery pack from the machine for sending. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

5. Figures

Illustrations are provided at the beginning of the operating instructions.

Symbol explanation:
             Movement direction
       Slow
  Fast
          First gear
           Second gear
       Screws
      Drill bit
        Without torque limitation
         Impact drilling
Nm              Torque

6. Overview

Fig. A
1 Keyless chuck
2 Sleeve (torque, drilling, impact drilling)
3 Switch (1st/2nd gear)
4 Rotation selector switch (rotation setting, transport lock) – both sides of the machine
5 Bit depot
6 Belt hook
7 Battery pack release button
8 Capacity indicator button
9 Capacity and signal indicator
10 Battery pack
11 LED lights
12 Trigger switch
equipment-specific

7. Use

7.1 Battery pack, capacity and signal display Fig. B

Charge the battery pack before use.

If performance diminishes, recharge the battery pack.

The ideal storage temperature is between 10°C and 30°C.

7.2 Removing, replacing battery pack Fig. C

7.3 Setting direction of rotation, transporting safety device (switch-

on lock) Fig. D

7.4 Selecting gear stage Fig. E

****Do not set the switch (3) unless the motor has stopped completely!

7.5 Setting torque limitation, drilling, impact drilling Fig. F

7.6 Switching on/off, setting speed Fig. A

Switching on, speed: press the trigger (12). The speed can be changed by pressing in the trigger.
Switching off: release the trigger (12). Note: The noise that the machine makes when it switches off is due to the design (quick stop) and has no influence on the function or the service life of the machine.

7.7 Keyless chuck Fig. G

With a soft tool shank, retightening may be required after a short period of operation.

Notes on machines with the designation SB…:

1. The ratchet sound which can possibly be heard after opening the drill chuck is functional and is switched off by a reverse rotation of the sleeve.
2. Clamping tool: Turn sleeve in direction “GRIP, ZU” until the noticeable mechanical resistance has been overcome.
Caution! The chuck is not yet fully tightened! Keep turning the sleeve ( it must “click” when turning) ) until it cannot be turned any further – only now is the tool safely clamped.

Cleaning: From time to time, hold the machine vertically with the keyless chuck facing downwards and turn the sleeve fully in direction “GRIP, ZU” and then turn fully in direction “AUF, RELEASE”. The dust collected falls from the keyless chuck.

7.8 Unscrewing chuck Fig. H

Employ the same procedure when attaching the chuck, except in reverse order.

7.9 Chuck with quick bit change system (for BS 14.4 LT Quick, BS 18 LT

Quick) Fig. I

To remove: Push the interlock ring forward (a), advance and pull off the chuck (b).
To mount: Push the interlock ring forward and move the chuck as far as the limit stop on the drill spindle.

7.10 Attaching the belt hook (depending on machine features)/bit depot

(depending on machine features) Fig. J

Attach the belt hook to the left (6), as shown.
Attach the bit depot to the right (5), as shown.

8. Troubleshooting

8.1 The machine’s multifunctional monitoring system

****If the machine switches off automatically, the machine electronics have activated automatic protection mode. A warning signal sounds (continuous beeping). The beeping stops after a maximum of 30 seconds or when the trigger (12) is released.

****In spite of this protective function, overloading is still possible with certain applications and can result in damage to the machine.

Causes and remedies:

1. Battery pack almost empty Fig. A, B (The electronics protect the battery pack against damage through total discharge).
   If one LED is flashing (9), the battery pack is almost flat. If necessary, press the (8) button and check the LEDs (9) to see the charge level. If the battery pack is almost flat, it must be recharged.

2. Long continuous overloading of the machine will activate the temperature cut-out.
   Leave the machine or battery pack to cool.
   Note: If the battery pack feels very warm, the pack will cool more quickly in an “AIR COOLED” charger.
   Note: The machine will cool more quickly if you operate it at idling speed.

3. Metabo safety shutdown: The machine was SWITCHED OFF automatically. If the slew rate of the current is too high (for example, if the machine suddenly seizes or kickback occurs), the machine switches off. Switch off the machine at the trigger (12). Switch it on again and continue to work as normal. Try to prevent the machine from seizing.

Switch off the machine at the trigger (12). Then continue working as normal. Try to prevent the machine from seizing.

9. Accessories

Only use original Metabo battery packs and Metabo accessories.

Use only accessories that fulfil the requirements and specifications listed in these operating instructions.

Fitting the angle drilling attachment Fig. K.

For a complete range of accessories, see www.metabo.com or the main catalogue.

10. Repairs

**** Repairs to electrical tools must be carried out by qualified electricians ONLY!

If you have Metabo electrical tools that require repairs, please contact your Metabo service centre. For addresses see www.metabo.com.

You can download spare parts lists from www.metabo.com.

11. Environmental Protection

Do not allow battery packs to come into contact with water!

To protect the environment, do not dispose of power tools or battery packs in household waste. Observe national regulations on separated collection and recycling of disused machines, packaging and accessories.

Before disposal, discharge the battery pack in the power tool. Prevent the contacts from short-circuiting (e. g. by protecting them with adhesive tape).

12. Technical specifications

Fig. L. We reserve the right to make technical improvements.

U           = Voltage of battery pack
n0          = No-load speed
Tightening torque for screwing:
M1         = Soft screwing application (wood)
M3         = Hard screwing application (metal)
M4           = Adjustable torque
Max. drill diameter:
D1 max    = in steel
D2 max    = in softwood
D3 max    = in concrete
s              = Max. impact rate
m             = Weight (with smallest battery pack)
G             = Spindle thread
D max       = Chuck clamping range
Measured values determined in conformity with EN 60745.

  Direct current

The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).

Emission values
Using these values, you can estimate the emissions from this power tool and compare these with the values emitted by other power tools. The actual values may be higher or lower, depending on the particular application and the condition of the tool or power tool. In estimating the values, you should also include work breaks and periods of low use. Based on the estimated emission values, specify protective measures for the user – for example, any organisational steps that must be put in place.
Vibration total value (vector sum of three directions) determined in accordance with EN 60745:
ah, ID = Vibration emission value (impact drilling into concrete)
ah, D = Vibration emission value (drilling into metal)
ah, S = Vibration emission level (screwing without impact)
Kh,… = Uncertainty (vibration)
Typical A-effective perceived sound levels::
LpA = Sound pressure level
LWA = Acoustic power level
KpA, KWA= Uncertainty (noise level)
During operation the noise level can exceed 80 dB(A).

Wear ear protectors!

Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com

170 27 1490 – 0818

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>