Dongguan Proyee Electronic Technology B8 Wireless Remote Controller User Manual
- June 5, 2024
- Dongguan Proyee Electronic Technology
Table of Contents
B8 Wireless Remote Controller
User Manual
INTRODUCTION
Thank you for purchasing our products!
This product has four modes: HSI, CCT, RGBW, and FLS. In different modes, color gamut, saturation, brightness value, color temperature, and light effects can be adjusted. Applies Bluetooth 5.0 wireless transmission technology, separate group frequency, and independent remote control. Without mutual interference, it enables you to easily control the fill light. With the low-power-consumption display screen, the parameters can be easily understood and adjusted. This user manual is aimed to provide better understand on how to use the product and help you simply handle the operation methods.
WARNING
- This product is an accessory for other electronic products. There might be a little defect possibility due to environmental issues.
- Power off the device and remove the batteries for long periods of non-use.
- The batteries should be installed correctly. Otherwise, it may cause the leak of corrosive liquids, heating or explosion.
- Do not use this product in high-temperature locations, such as an enclosure car. Do not expose this product to strong direct sunlight, car dashboard, or other overheating places.
- Keep it dry. Do not touch this product with wet hands. Do not expose this product to water or rain.
- Do not use it with inflammable gas. Otherwise, it may cause an explosion or fire.
LIST OF ITEMS
DISPLAY
INSTALL BATTERIES
Install and Change Batteries
When in low battery, the low battery icon [ ] on the display screen blinks, it
shows that the battery is running out. Please be ready to spare batteries.
The transmitter is powered by AAA batteries.
Note:
Please install batteries correctly to the compartment according to the+ and –
terminal of the batteries.
USAGE
1. Power ON/OFF
Push the Power Button upward to [ ], the screen will display the relevant
parameter values. Push it downward to [ ], the remote controller will be
turned off.
2. Channel Setting
Press the [ CH ] button to select channel icon, and enter the channel
setting. Then rotate the dial to select channel from 1 to 48. Press the [
CH ] button again to exit channel setting after channel selection.
Note: The remote controller only works with the LED panel lights under the same channel.
3. Group Setting
Press the [ GP ] button to switch the group between A/B/C/D/E/F (6 groups
in total).
Note: Remote controller only works with the LED panel lights under the same channel.
4. Brightness Quick Adjustment
Press the Brightness Quick Adjustment button [ ] to quickly cyclically adjust
the brightness between 0%, 1%, 25%, 50%, 75%, and 700% (0% stands for turning
off the lights).
5. Mode Setting
Press the button [ ] to switch cyclically between the four modes of Color
Gamut Mode (HSI), Color Temperature Mode (CCT), Light Effect Mode (FLS), and
RGBW Mode(RGBW).
6. Color Temperature Mode Regulation (CCT)
Press the switch button[ ], the icon [ CCT ] will be displayed on the
upper right corner of the display screen. Press the Confirm Button
continuously to move the setting icon to brightness adjustment/color
temperature adjustment. Rotate the dial to adjust the parameters of brightness
from 0% to 100% and color temperature from 2500 to 10000K.
Color Temperature Adjustment
After entering the Color Temperature Mode (CCT), continuously press the
Confirm Button to move the lighted icon to the color temperature setting
position[ ]. Rotate the dial to adjust the color temperature of from 2500 to
10000K. Rotate to left to decrease the parameter of color temperature, and
rotate to right to increase the parameter of color temperature.
Color Compensation
In CCT mode, press the button on the middle of the dial to select color compensation, and rotate the dial wheel to adjust parameter values from -100% to 100%.
7. Color Gamut Mode (HSI) Adjustment
Press the [ ] switch button, the icon [ HSI ] will be displayed on the
upper right corner of the display screen. Press the Confirm Button
continuously to move the lighted icon to brightness adjustment/full-color
gamut adjustment/saturation adjustment. Rotate the dial to adjust the
parameters of brightness from 0% to 100, full color gamut from Oto 360 °, and
saturation from 0%to100.
Brightness Control
After entering the Color Gamut Mode (HSI), continuously press the Confirm Button to move the lighted icon to the brightness setting position [ ]. rotate the dial to adjust the brightness from 0% to 100%. Rotate to left to decrease the brightness parameter, and rotate to right to increase the brightness parameter
Full Gamut Adjustment
After entering the Color Gamut Mode (HSI), continuously press the Confirm Button to move the lighted icon to the full color gamut setting position [ ], and rotate the dial to adjust the full gamut from O to360 °.
Saturation Control
After entering the Color Gamut Mode ( HSI ), continuously press the
Confirm Button to move the lighted icon to the saturation setting position [
], rotate the dial to adjust the saturation from 0% to 100%, rotate to left to
decrease the saturation parameter, and rotate to right to increase the
saturation parameter.
8. Light Effect Mode Adjustment ( FLS )
Press the [ ] button, the icon [ FLS ] will be displayed on the upper
right corner of the display screen. Press the Confirm Button continuously to
move the lighted icon to brightness adjustment/special effect adjustment.
Rotate the dial to adjust the parameter value of brightness from 0% to 100%
and select a specific effect.
Light Effect Selection
After entering the Light Effect Mode [ FLS ], continuously press the
Confirm Button to move the lighted icon to the light effect setting position [
], rotate the dial to select the required light effect, and select from# 01
to# 70 light effect.
9. RGBW Mode
Press [ ] to switch modes until [ RGBW ] displayed on top right corner of
the screen. Press the button on the middle of the dial to set
R-Red/G-Green/B-Blue/W-White colors separately, and rotate the dial to adjust
parameter value from Oto 255.
SPECIFICATIONS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>