Harman Industries HSA-20NP-PB Harman Polaris Plugin User Guide
- June 5, 2024
- Harman Industries
Table of Contents
Harman Industries HSA-20NP-PB Harman Polaris Plugin
About Polaris Plugin
Polaris Plugin is an intelligent OBD solution, which integrates a 3G/4G
module, GPS, acceleration sensor and ECU communication module. Developed on
Qualcomm chipset and NXP MCU, it can provide vehicle position, collect
statistics on vehicle trajectory, reconstruct driving behavior, collect
statistics on fuel consumption, track vehicle to prevent theft, read vehicle
status, read/clear vehicle fault codes, etc. This OBD solution is well
applicable to individual consumers, fleet management, UBI, vehicle rental and
vehicle maintenance.
Product Functions
- UMTS / LTE communications
- Real-time vehicle data
- Vehicle DTC code
- GPS/GLONASS/BDS/A-GPS positioning
- Supplementary transmission for Blind-area data
- Swapping alarming
- FOTA upgrade
- Sleeping and awaking
- Driving behavior analysis
Package Content
Product Features
How to Start
Used only in North America
LED Indicator
This device was tested for body-support operations. To comply with RF exposure requirements, a minimum separation distance of 1.5cm must be maintained between the user’s body and the device, including the antenna. Body- accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Safety Warning
Please use a battery specified by the device manufacturer. Otherwise, all warranty services are invalid. The device manufacturer will not provide a warranty for damage caused by non-OEM accessories.
- Do NOT put the device into water or fire.
- Do NOT bend or open the battery.
- Do NOT recharge the battery.
- Do NOT disassemble the device. Improper handling might damage the device permanently.
FCC
Ride Command Plus device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) The device may not cause harmful interference, and (2) The device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution ： Any Changes or modifications not expressly approved by Ride Command Plus for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment should be installed and operated with a minimum distance of 15
mm between the device and your body.
WARNING : This product can expose you to chemicals including lead, which
are known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to
www.P65Warnings.ca.gov
6 ISED Warning statements
Ride Command Plus device contains license-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development Canada’s
licenceexempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Innovation, Science et développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
ISED Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 15 mm between the radiator and any part of
your body. Pour se conformer aux exigences de conformité CNR 102 RF
exposition, une distance de séparation d’au moins 15 mm doit être maintenue
entre l’antenne de cet appareil ettoutes les personnes.
Others
Importer Name: Polaris Sales Mexico S. de RL de C.V. Importer Address: Ave. Lazaro Cardenas 2225 Piso 6, San Pedro Garza Garcia, NL 66269, Mexico Brand: Ride Command Plus HW Version: V1.0 Electrical Specifications (Voltage, Current, Frequency):Voltage：9-16V DC, Current ：1A max @ 12 V @ 25 Deg （Normal Operation ） Country of Origin: China Warning to read user manual before use
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>