POWER CRAZE Shift 24 High Speed RC Buggy Instruction Manual

CRAZE Shift 24 High Speed RC Buggy
Instruction Manual

Thank you for purchasing the SHIFT 24. With proper care, your new SHIFT 24 will provide you with many hours of enjoyment. Please read this instruction manual completely  before using the product for the first time and then keep this manual in a handy place for future reference.

Colors and styles may vary slightly.

PACKAGE CONTENTS

• 1 SHIFT 24 High Speed Truck
• Remote control
• USB charging cord
• Two sets of tires

CHARGING THE BATTERY

1. Make sure the power button on the SHIFT 24 is off, then insert the square charging plug side of the included USB cord into the trucks charging socket on the bottom of the  truck. The square plug only fits  in one direction. DO NOT FORCE THE CHARGING PLUG! (see illustration A,B).
2. Connect the other end of the USB cord into your computers USB port or a USB wall charger (see diagram C), The Red CHARGE indicator light turns OFF while the  charging is in progress and ON when the SHIFT 24 is fully charged.
3. Average charging time is approximately 40-50 minutes (via 5.0V 2A USB wall charger). The truck  operates for approximately 12-15 minutes on full charge.
4. Don’t forget the red LED charging indicator on the USB cord turns ON when the battery is fully charged.

*SAFETY TIP: Periodically examine the USB charging cord for external damage. External damage to the charging cord may result in the risk of fire or electric shock. Never  use a damaged charging cord or compromised wall adapter.

INSTALLING BATTERIES INTO THE REMOTE CONTROL

Turn the included remote controller upside down with the battery door facing you. Secure the controller with one hand and with your other hand place your thumb on the  center of battery door and slide the cover off (see diagram D). Insert 3 AA batteries (not included) into the battery compartment. Make sure to match the polarity (+ and -)  marked clearly inside the battery compartment. Replace the battery cover by sliding it on in the reverse direction until you hear a “click” sound notifying that the cover is locked in place and secure.

TRUCK DIAGRAM

REMOTE DIAGRAM

SYNCING YOUR SHIFT 24

Your SHIFT 24 utilizes an automatic 2.4G digital channel selection system that allows up to 8 individual players to race side by side in the same wireless range without  nterference.
FOR SOLO PLAYER:

1. Before starting, make sure that the power on both your remote control and truck are in the OFF position (the on off power button is on the under carriage of the truck next  to the charging socket)
2. First turn ON the truck and set it down on a flat surface. The head lamps will be flashing rapidly letting know that the truck has power and is ready for syncing.
3. Next turn ON the remote control. The head lamps should stop flashing and immediately become solid indicating that you have successfully synced your SHIFT 24.

*Note: If pairing fails frist make the sure that batteries are properly installed in the controller and truck and then turn both of and repeat steps 1-3 above.

FOR MULTIPLE PLAYERS:

1. Before starting, make sure that the power on all the trucks and all the controllers are in the OFF position.
2. Following a one by one sequence, each player should sync their truck one at a time by Follow steps 1 to 3 above.
3. IMPORTANT: after syncing each truck, make sure to leave each truck ON until all players have completed the syncing process.
4. If there is an interference problem, all players must turn off their controllers and trucks and restart the process again.

HOW TO OPERATE YOUR SHIFT 24:

SPEED SETTINGS

Your SHIFT 24 comes with 2 speed settings for beginner and more advanced drivers. For beginner drivers we suggest you start in the LOW SPEED setting (SEE SPEED  MODE SWITCH DIAGRAM E). In the low speed setting your SHIFT 24 truck has all the same proportional steering and proportional acceleration functions as in the high  speed setting but the speed is governed for younger drivers and beginners who are just learning how to control their new vehicle. In HIGH SPEED setting the SHIFT 24 can  reach its maximum speed and power.

PROPERLY USING THE THROTTLE

The SHIFT 24 is unlike most toy RC cars as it uses digital proportion acceleration. This feature comes from the higher-end hobby car industry and it makes driving your SHIFT  24 so much more fun and controllable! With digital proportional speed your SHIFT 24 has a wide range of sensitivity and speed control. For example; you can practice  driving very slowly, you can control the rate of acceleration and you can adjust your speed up and down on the fly creating tight turns or instant straight-away acceleration. The  digital throttle is very sensitive so we strongly suggest to begin practicing with a very gentle finger on the throttle until you can begin to understand and feel how to control the  speed.

REACHING TOP SPEEDS
The SHIFT 24 has been clocked at speeds above 24MPH. To achieve the vehicles top speeds, you must first have a large open outdoor space with a fairly smooth and hard  surface. Make sure you have at least 100 feet of length and 12 feet of unobstructed width for your runway (6 feet on either side of your vehicle). Next make sure your controller  speed setting is set to HIGH SPEED mode. Next adjust and test the left/right trim so the SHIFT 24 drives in a fairly straight line without steering wheel input. Now you’re  ready! Let go of the steering wheel and allow the tires be held in line by the automatic digital steering control system. From zero start the truck rolling by gently, gradually and  consistently pulling back the throttle until the throttle stick hits the back wall of the controller. PRO TIP: You will need to make very tiny left / right steering inputs to keep the  SHIFT 24 in a straight line while you push the SHIFT 24 to maximum velocity! *Road condition, environmental condition and operator skill can affect performance.

ADJUSTING THE TRIM
The SHIFT 24 comes with a digital proportional steering system. This special steering system allows the driver to perform more accurate turning functions and helps to keep  the car in-control on the road! Before starting play, and from time to time after using your SHIFT 24 (especially after a few crashes and rolls), you should adjust your steering  trim so the SHIFT 24 drives in a “generally straight” line without touching the steering wheel. On the face of your controller you will see the trim button with an L and R (right  and left) on either side (SEE DIAGRAM F) with the power button on and truck synced to the controller, slowly turn the Trim Dial right and left. You should see the front tires  move (note you should not be driving the car or touching the throttle while trimming). Once you feel the tires are straight you should test this by not touching the steering wheel  and just gently pulling on the throttle. The car should follow a “generally straight line”. Note it is normal for the car to have a slight leftward or rightward drift. This will
not affect steering and driving performance.

PROPERLY STEERING THE VEHICLE

The SHIFT 24 has 6-way control with digital proportional steering. The SHIFT 24 has the ability to go straight-forward,straight- backwards, forward-left, forward-right, reverse- left and reverse-right (See Diagram G). Digital Proportional Steering is a unique feature rarely found on toy RC vehicles. With the SHIFT 24 proportional steering system you  can accurately control your vehicle in all types of situations making driving this truck a blast! We suggest practicing with gentle movements on the steering wheel so you can get  used to the feeling and sensitivity of the SHIFT 24 steering system. Start slow and remember practice makes perfect!

ENHANCED PERFORMANCE TIRES
Your SHIFT 24 comes with a pair of grey colored enhanced performance tires (see image H) these enhanced performance tires were made out of extra-soft TPR with lower  internal air-compression for improved steering control on smooth or slippery surfaces. The enhanced performance tires are great for indoor or outdoor racing when you need  extra control on smooth surfaces.

PRO TIP: The performance tires are not advisable for off-roading or rougher roads and street terrain.

WARNING

DO NOT USE TRUCK IN INCLEMENT WEATHER!

TROUBLESHOOTING

Before sending your truck in for repair, please check for a solution below.

remote control and recharge the truck.
Truck does not respond properly to remote control.| Truck and remote not synced properly
Another RC truck may be transmitting on the same radio frequency| Refer to sync section and re-sync your trucl and remote.
Move to a new location where no other R( trucks are present.
Truck loses connection to remote control.| Using truck in a small enclosed area Using truck indoors
Low batteries in transmitter or vehicle| Move outdoors to a large open area.
Install new batteries in remote control or recharge your truck.
Truck battery is fully charged, but slower than normal.| Driving truck for too long at high speeds, causing motor to overheat| Turn truck off for 10-15 minutes.

SAFETY WARNINGS!

• Improper use of batteries may lead to overheating, breakage or leaking.
  – Do not mix old and new batteries.
  – Do not mix different battery brands.
  – Install batteries with correct polarity. The flat side (negative terminal) of the battery should rest against the spring.
  – Remove dead batteries immediately.
  – Avoid liquids, which can short circuit the batteries.
  – The truck or remote will become unresponsive when batteries are low, at which point you should replace all batteries with new ones.
  – Remove the batteries if you will not use the truck for a long time.

• Avoid using near furniture or glass to prevent damage to these objects.

• Do not play on roads.

• Do not play in crowded areas to avoid injury or damage. Choose a safe location away from traffic.

• Do not use truck during a storm or when lightning or thunder are present.

• Do not use in a wet , sandy or muddy environment as truck may become damaged.

• Do not modify or attempt to replace the built-in original antenna on the remote or truck. Doing so will damage the set and affect operation.

• Do not pull on any wires that are part of the truck. Such action may cause the wires to break and the truck to malfunction.

• Keep fingers, hair and clothes away from the truck’s spinning tires. Failure to do so may result in physical injury.

• Never aim the truck at other people.

• Do not throw the truck or purposely hit it with any object.

• Store truck in a cool environment, away from high-temperature sources such as fires, stoves, radiators, etc.

• This truck has no user-serviceable parts. Do not attempt to modify components or circuit board.

• This toy is only to be connected to equipment bearing either of the following symbols: or

RECHARGEABLE BATTERY:
This SHIFT 24 uses an internal rechargeable battery and is not replaceable. If the battery no longer stays charged, dispose of it properly according to local disposal equirements.
CAUTION: If the rechargeable battery leaks fluid, avoid contact with eyes and dispose of the SHIFT 24.

Limited 90-Day Warranty

AMAX Group USA warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If  any such defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and  insured to our warranty center ALONG WITH THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail partner and that the  product is still within the 90 day warranty period. The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all  warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals or companies. Any applicable implied warranties, including  warranties of merchantability and fitness, are hereby limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any  applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental  or consequential damages, so the above limitations and exclusions in these instances may not apply.

REPAIR/REPLACE PRODUCT

If your product begins to malfunction or stop working, immediately contact our warranty center (contact details listed below). If it is determined that a return is necessary, our  warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product to us. When honoring the warranty, AMAX  reserves the right to either repair, replace or refund the product.

IMPORTANT NOTICE:

We will reject and return to sender returns that are not accompanied by an AMAX issued RMA form and RMA number so make sure to contact our warranty center before  attempting to return your product!

PREPARATION FOR SHIPPING YOUR PRODUCT:

Please repack your product in a durable box, preferably in the original carton, and send it prepaid, and adequately insured. Include the RMA form that was issued by our  warranty department along with your daytime telephone number and email address inside the shipping carton. If your warranty has expired and you still require service please  contact our customer care team For further information please send all inquiries to: [email protected]

IMPORTANT NOTICE!
DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK
WITHOUT FIRST CONTACTING OUR WARRANTY
DEPARTMENT AT:
www.amaxbrands.com
Email: [email protected]

FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur  in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY
BRENTWOOD, TN 37027
For customer support,
call: 1-888-376-9601
www.TractorSupply.com

WARNING:
CHOKING HAZARD – Small Parts.
Not for Children under 3 years.

Conforms to safety requirements of ASTM, FCC and CPSIA.
This product is manufactured by Amax Group
12645 Memorial Drive Suite F1 #388 Houston, TX 77024
Power Craze™ & SHIFT ™ 24 are the registered trademarks of Amax Group USA, LLC.
©2021. All rights reserved. Visit us at www.amaxbrands.com

Made in China
C012-USA-V 1.0

Documents / Resources

| POWER CRAZE Shift 24 High Speed RC Buggy [pdf] Instruction Manual
Shift 24 High Speed RC Buggy
---|---

References

• Amax Brands

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>