AITEK INC AMP-500-01 Aitek Miner Plus User Manual
- June 5, 2024
- AITEK INC
Table of Contents
INC AMP-500-01 Aiptek Miner Plus
User Manual
PACKAGE CONTENT
Package Content
Quantity | Description |
---|---|
1 | Aitek Miner Plus |
1 | Lora Antenna |
1 | Power Adaptor |
1 | Mounting Bracket (attached to the Miner Plus) |
2 | Mounting Screw |
PRODUCT SPECIFICATIONS
Aitek Miner Plus
Product Specifications
CPU| Quad-core A55
RAM| 2GB LPDDR4/ LPDDR4X
Flash| 64GB eMMC 5.1
WIFI| 802.11 b/g/n WLAN
Bluetooth| BT5.1/BLE+EDR
RF Connectivity
Frequency Band| US915
Frequency| 902-928MHz
Channel Capacity| 8-channels uplink, 1-channel downlink
Work model| Half-duplex
Output Power| s1W
Connectors
Antenna| Lora, SMA-K
Ethernet| 10/100M
Power| DC12V/1A
Button| Activate Bluetooth
SD Card slot|
Mini USB corn port|
Environment & Others
Operating Temperature| 0°C to 60°C
Storage Temperature| -40°C to 85°C
Relative Humidity| 20% – 90%, non-condensing
Dimensions (L`W*H)| 175.9 x 148.5 x 51 mm
Color| Silver
INTRODUCTION
Aitek Miner Plus is a high-performing indoor loT hotspot gateway compatible
with Helium Network (www.helium.com), which combines
the leading wireless LongFi protocol and Helium Blockchain technology.
Aitek Miner Plus is compatible with all LongFi devices. Aitek Miner Plus is
designed with an ECC608 crypto chip to provide secure and reliable
connectivity. It meets Helium security protocol and provides trouble-free
operations for end-users. Additional benefits include:
- Operates with ultra-low power consumption (5W)
- Covers more than 10 miles of signal range
- Provides connectivity to thousands of LongFi end nodes within its range
NETWORK SYSTEMS
Aitek Miner Plus hotspot gateway integrates LongFi packets with Helium Miner. The hotspot sends the received LoRa terminal data packets to Helium Miner, then forwards them to the Console (Network Server) via the Miner. After that, pushes it to the application platform via the API interface.
INTERFACE DESCRIPTION
LED INDICATOR DESCRIPTION
The different colors of the LEDs represent different working states of the device.
Status LED Color | Indicator Status | Description |
---|---|---|
The gateway is configured and operating normally. | The network connection |
is normal.
| The gateway is in standby/off-line mode| The network is not connected
| The gateway power-on initialization status
| Bluetooth is activated, can be scanned and connected| Press BT BOTTON for 2
seconds to activate
No LED light| Power off| The device is not powered on
Please note During the software update, after connecting to the network, the green light may not be turned on immediately. The green light will turn on after the normal update and the hotspot is paired to the network successfully.
USER INSTRUCTION
Download the mobile app.
Download the app using Apple iPhone:
- Go to Apple app store button, and search for the Helium app.
- Download and install the Helium app
- Run the Helium app
- Continue to step 7.2
Download the app using an Android phone:
Go to the Google Play store,
- Go to Google Play Store, and search for the Helium app.
- Download and install the Helium app
- Run the Helium app o Continue to step 7.2
Configure network connection
Equipment hookup
Connect the antenna by inserting the SMA male connector to the LoRa antenna
port. Turn the nut of the connector until it is fully tightened.
Set up distribution network — Using WiFi, Ethernet, or Bluetooth
Open the Helium App from your phone, register to enter, and select “Set up
Hotspur.
Select Aitek Miner Plus, read the “network configuration instructions” if you
haven’t read it, or bypass the “network configuration instructions” by
selecting “Skip” to follow the on-boarding step-by-step prompts on the app.
Once ready, power up the gateway by plugging in the power adapter AC end to an
AC power outlet and plug the DC end to the DC 12V socket on the device.
After plugging in the power, the LED of the gateway turns red and then yellow.
Below are steps showing three methods of pairing the Aiptek’s Miner Plus hotspot. Please note, that only one of the three methods is needed to pair up the device.
-
WiFi pairing:
If you use the WiFi pairing technique, select the WiFi from the app, and select the name of the WiFi router you are networking with. Enter the network password and press “next”. Follow the app’s step-by-step process. Once onboarding is successful, the LED light will turn green. -
Bluetooth pairing:
Insert a pin into the BT BUTTON hole and press the button for 2 seconds, then watch the LED turn blue to Start Scan. After scanning the device, click to enter the next step. Follow the app’s step-by-step process.
At this step, the network pairing is completed, LED color will change from blue to green. -
Ethernet Cable Connection
Ethernet connection requires connecting an Ethernet cable from Aiptek’s Miner Plus to the network router equipment (the Ethernet cable is provided by the customer). Suggest using CAT 6 or a better-rated Ethernet cable when possible.
Please note that the Ethernet connection currently only supports automatic IP acquisition.
Follow the app’s step-by-step process. Once onboarding is successful, the LED light will turn green.
PART SIZE (MM)
MOUNTING GUIDE
Aiptek’s Miner Plus hotspot gateway can be mounted in the following methods.
- Desktop: Place the gateway on a horizontal surface.
- Wall-mount: Hang the gateway on the wall using the proper wall mounting screws to fully secure the device.
RF Antenna placement — best practice for strong signal:
- Place the antenna in an open space where possible.
- Place the antenna at the highest part of the house or structure where possible.
- The antenna should have a minimal blockage from building materials such as concrete walls, sheetrock walls, metal beams, etc.
- Avoid obstructing the antenna with metal objects such as metal appliances, metal doors, etc.
- Try to place the antenna close to a window or balcony as possible, so the antenna can provide wider coverage.
Precautions:
- The hotspot must be handled with care during the installation process. Avoid shocking or dropping the product.
- The working environment of the hotspot should be in a low dust area, with good air circulation.
- Avoid high humidity areas where water condensation could damage the hotspot.
- This hotspot is not rated for direct exposure to water.
APPENDIX -A
FCC ID: 2A5L2-AMP500
Important Safety Information – Read First
Before installing, configuring. or operating any equipment, Aitek recommends
the user to access and read all relevant technical documentation. Aitek
technical documentation can be found at Aiteks.com. Read and understand all
safety instructions, cautions, and warnings in this document and the labels on
the equipment.
Safety Statements
All safety instructions below should be read, understood, and applied under
all relevant circumstances when working with this equipment.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators. stoves. or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of any polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If any provided plug does not fit into your outlet. consult an electrician for the replacement of the obsolete outlet.
- Protect any power cord from being walked on or pinched: particularly at plugs. convenience receptacles, and the point where they exit from the apparatus.
- Use only attachments/accessories specified by the manufacturer, following all relevant safety precautions for any such attachments/ accessories.
- Disconnect any outlet-powered apparatus from its power source during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a damaged power supply cord or plug, the liquid being spilled or objects have fallen into the apparatus. the apparatus is exposed to rain or moisture, apparatus having been dropped, or another failure to operate normally.
- To completely disconnect the equipment from AC mains power, disconnect the power supply cord plug from the AC receptacle.
- For applicable equipment, use the included power cord with the grounding prong intact to ensure proper grounding of the device.
- For any hardwired or fixed in-wall apparatus, carefully follow all wiring diagrams and instructions. All electrical wiring and servicing should be performed by a properly licensed electrician.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the requirements for
CLASS B digital devices pursuant to Part 15 of FCC Rules. These requirements
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. If this equipment does cause harmful interference to
radio or television reception (which can be confirmed by turning the equipment
off and on), the user is encouraged to attempt to correct the interference
using one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Ensure that the power sources for this equipment and the receiver are connected to different circuits.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radiofrequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the
radiator & your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>