iSecus G130Plus Cellular + Wi-Fi Alarm System User Guide
- June 6, 2024
- iSecus
Table of Contents
- iSecus G130Plus Cellular + Wi-Fi Alarm System
- SPECIFICATIONS
- IN THE BOX
- Optional.
- AT A GLANCE
- Wi-Fi Indicator
- Cellular Indicator
- Arm Indicator
- Alarm Indicator
- Power Indicator
- SIM Card
- DO THIS FIRST
- CONNECT TO WIFI
- HOW TO ADD/PAIR WIRELESS DEVICE
- HOW TO CONNECT WIRELESS SIREN
- PLACEMENT INSTALLATION
- GETTING STARTED
- SECURITY MODES
- SENSOR/ZONE RESPONSE TYPE DEFFINITIONS IN APP
- NAME A ACCESSORY
- CHANGE SETTINGS IN APP
- RESET
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
iSecus G130Plus Cellular + Wi-Fi Alarm System
The panel cellular+Wi-Fi model is a dual network system that utilizes both Wi- Fi 802.11 b/g/n(2.4GHz) and cellular(GSM). All sensors are wirelessly connected to the panel. In the event of alarm activation, for example, when a sensor is triggered, a push notification will be sent and an alarm call will be made automatically to all registered users. The system can be controlled on-site by the remote tag supplied, or remotely from anywhere with our free dedicated mobile application. The panel can connect with up to 100 wireless sensors, 10 remote tags, multiple wireless sirens and an external siren . If the building has lost electrical power, the backup battery built-in the panel provides power operation up to 3 hours.
SPECIFICATIONS
- Power Supply: Micro USB+5VDC/1000mA
- Backup Battery: 3.7V, 300mAh Lithium-ion Battery Consumption: <150mA@normal
- GSM: 850/900/1800/1900MHz
- Wi-Fi: IEEE802.11b/g/n
- Radio Frequency: 433Mhz
- Connectivity: wireless siren and up to 100 wireless sensors Operating Temperature: -10~55℃
IN THE BOX
- Base Station (Alarm Panel) x1
- Mounting Screws x2
- Door Sensor x1
- Motion Sensor x1
- User Guide x1
- Power Adapter x1
- USB Cable x1
- Configuration Switch Tool x1
Optional.
- Wireless Siren
- Wireless Keypad
- Doorbell Button
AT A GLANCE
- Wi-Fi Indicator
- Cellular Indicator
- Arm Indicator
- Alarm Indicator
- Power Indicator
- Configuration Switch
- Tamper Switch
- Bracket
- Built-in Siren
- SIM Card Slot
- Power Port (Micro USB)
- Backup Battery ON/OFF Switch
Wi-Fi Indicator
What you see | What it means |
---|---|
Blinking quickly | Wi-Fi connection configuration |
in Smart / EZ Mode
Blinking slowly| Wi-Fi connection configuration
in AP Mode
Solid| Connected to internet
Pulse per 4s| Connecting
Nothing| Wi-Fi module failure
Cellular Indicator
What you see | What it means |
---|---|
Solid | Cellular network is available |
Pulse per 4s | Searching network or no SIM card |
Blinking | Calling or text message sending |
Nothing | Cellular module failure |
Arm Indicator
What you see | What it means |
---|---|
Solid | Away armed mode |
Breathing | Home armed mode |
Nothing | Disarmed |
Blinking | Entry delay @ quickly, Exit delay @ slowly |
Alarm Indicator
What you see | What it means |
---|---|
Blinking | System Alarming |
Nothing | Normal |
Power Indicator
What you see | What it means |
---|---|
Breathing | Charging |
Solid | Charged fully |
Nothing | No battery or battery switch is off |
Blinking | Powered by battery @slowly |
Low battery @quickly
SIM Card
A regular SIM card is required to use cellular services when connecting to GSM networks. Install it before getting started.
DO THIS FIRST
Scan the QR code or find “Smart Life” from GooglePlay/APP Store to get the free application for Android or iOS. Upon installation of APP on your phone, the app will guide you through registering.
CONNECT TO WIFI
With EZ Mode (Default).
- STEP 1. Power your panel, insert a paper clip or the included tool into the hole on the bottom, then press and hold Wi-Fi configuration switch until the Wi-Fi indicator blinks quickly (0.1s on and 0.1s off), then it is ready to be connected.
- STEP 2. On App home page, tap “+” icon, select Sensors from Add Manually, then select Alarm(Wi-Fi) from devices list.
- STEP 3. Choose your local 2.4GHz Wi-Fi (NOT 5GHz) and input password,then choose EZ Mode (default) in the top right corner, then follow on-screen instructions in the app to complete the connection.
IMPORTANT: Please turn to AP Mode to connect again if the connection fails in EZ Mode. Do as following.
Or with AP Mode.
- STEP 1. On your panel, one more time, press and hold Wi-Fi configuration switch until the Wi-Fi indicator blinks slowly (1s on and 1s off), then it is ready to be connected.
- STEP 2. Do the same step 2 in EZ mode, then in the top right corner, choose AP Mode, then follow on-screen instructions in the app to complete the connection.
HOW TO ADD/PAIR WIRELESS DEVICE
The wireless sensors supplied with this kit are paired with panel. IF NOT or you want to pair more, you might easily pair wireless accessories with your panel as following.
- STEP 1. At your device home page in APP tap Accessories >+, then the panel goes into the pairing/sniffer mode with all indicators blinking.
STEP 2. Trigger your wireless accessory that need to be added to send a transmission signal to panel before its 20s sniffer countdown expires, then the panel sounds a tone. After the accessory is added,each of them will be classified to each corresponding column automatically in APP.
You need to know in step2. To pair a door sensor, start with door sensor and magnet closely aligned, then separate until blue light comes on.(Don’ t active tamper switch). To pair a keypad, enter USER PASSCODE+DISARM BUTTON on keypad to be paired. If you want that the doorbell button of keypad can be used, you need to pair with panel again using doorbell button.
HOW TO CONNECT WIRELESS SIREN
- STEP 1. Press and hold the SET button of siren until you hear one beep, then the siren goes into the sniffer mode and the light is on.
- STEP 2. In APP tap Panic button to active an panel alarm to send a transmission signal to the siren .
- STEP 3. The siren gives a long beep of successful indication.
Note: In case of an alarm, the siren sounds at 100dB.
PLACEMENT INSTALLATION
Before installation, please test the wireless sensors range first. It is not advised to mount the motion detector or door/window sensor onto metal surfaces as the material can block RF signals between the transmitter and the base station. Please clean the flat area where you intend to install the sensors. Using double-sides adhesive tap to install the motion detector or door/window sensor.
Panel
Choose an wall outlet with a good Wi-Fi and cellular signal that’s not
controlled by a switch, so you don’t accidentally turn off the panel. Connect
the power cord to the USB port and plug the power adapter into the outlet to
power on your panel, then slide the battery switch to on .
GETTING STARTED
Set phone numbers in APP
Up to 5 stored Phone Numbers will receive text messages (SMS) and phone calls
in case of triggered alarms. In APP, tap Setting > Alarm call number to add
phone numbers and tap Alarm call to turn alarm call on. Tap Alarm SMS number
to add phone numbers for receiving SMS and tap Alarm SMS to turn alarm text
message on.
Tips: The panel will make phone calls to the stored phone numbers successively (up to 2 rounds in turn). If the phone call is answered and any Keypad Command has been operated by one of these users, it will stop calling the next phone number; otherwise it will continue to remind users until it is up to 2 rounds. When the stored phone calls the panel, two-way talk is connected automatically.
Keypad Command:
WHICH BUTTON YOU
PRESS ON PHONE
| WHAT HAPPENS
---|---
1| Arm
2| Disarm or silence when the alarming is sounding
3 or 4| Two-way talk
SECURITY MODES
Place your panel in Home mode to disarm your interior sensors, while keeping your exterior sensors armed. Set to Away mode to arm all the sensors in your home to know what happens while you’re out. And Disarm your system to disarm all sensors and freely walk in and out of your home.
No Rush.
With No Rush, you can take the time you leave home or disarm before the alarm
sounds. By default, you have 40 seconds. To adjust the countdown timing in
APP, tap Settings > Exit Delay and Entry Delay to change the delay you want.
Using APP
- Tap Security to away arm.
- Tap Home to home/partial arm.
- Tap unlock to disarm.
- Tap Sos to trigger an emergency alarm.
Tips: When you arm the system, the panel will say “Hello, the door or window is unclosed ” (or sound an alarm ) if you leave the door or window open. In APP, tap Setting > Timer to edit the schedules for arming/disarming your system automatically at a daily time.
SENSOR/ZONE RESPONSE TYPE DEFFINITIONS IN APP
Each of sensors is specified a Zone mode, which defines the way in which the
system responds to faults in that zone.
Tap Accessories and pick the sensor you want to set, then change Zone Mode
from list described as followings.
-
Normal: Sensors set to Normal Zone are activated in Arm (full arm) or HOME Mode (home/stay/partial arm). We recommend setting door/window sensor to Normal Zone.
-
24 Hours: Sensors set to 24H Zone will activate the alarm and sounding when triggered, regardless of the alarm status
(Armed or Disarmed). -
Delay: If sensors set to Delay Zone are triggered, the panel will sound the alarm after the delay time passed. We recommend setting door sensors with a delay if they are used as primary entryways.
-
Home: Sensors set to Home Zone are only activated in Arm (full arm). If Stay Arm Mode (partial/home arm) is used, these sensors are not armed and will not activate the alarm if triggered. We recommend setting PIR Motion Detectors to Home Zone.
-
24 Hours Silent: The mode is same as 24 Hours but no sound.
-
Home with delay: It is same as Home but with Entry Delay in Arm. To disable the sensor, select Off.
NAME A ACCESSORY
You can give the accessory a name. Pick your accessory in Accessories list, tap name, then enter a name (not to exceed 16 characters) such as “Front door”, then tap save to save your setting.
CHANGE SETTINGS IN APP
Exit delay & Entry delay
Your security system has been programmed with delay times that allow you to exit your home after arming, and to disarm the system upon entry before an alarm occurs. If you leave home too late when exiting, or disarm too late when arriving home, it will cause a false alarm. If an false alarm occurs, you should disarm the system immediately.
Alarm duration
Adjust alarm sound duration from 0 to 59 minutes. Set it to 0 to turn alarm
sound off when an alarm occurs.
Door/window unclosed notification
Enable to receive notification while you leave the door or window opened with
arming.
Sensor low battery notification
Enable to receive notification when the wireless accessory is low battery.
Countdown with tick tone
Turn countdown tick tone on or off while the panel is during Exit Delay or
Entry Delay.
Notification on/off
Turn all notification switch on or off.
Factory reset
Reset your panel to factory settings and removes all pairings.
Hub language
Choose the notification language.
RESET
This process resets your panel to factory settings and removes all pairings. Tap Settings > Factory reset in APP, or click Configuration Switch more than 15 times until the panel sounds a tone, then the panel restarts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>