PRAXIS M30-THRU Adults Unisex User Guide
- June 5, 2024
- PRAXIS
Table of Contents
PRAXIS M30-THRU Adults Unisex
Specifications
-
* **Crankset:** Compatible Praxis M30-THRU & other-brand cranks (30mm DRIVE/30mm NON-DRIVE)- Frame Shell: BSA 68mm Road Frames | BSA 68/73mm MTN Frames
- Required Tools:
- 30mm ID X 1mm Dust Cover – Qty 1
- 30mm ID X 2mm Dust Cover – Qty 1
- LEFT/NON-DRIVE Cup with 30mm ID Bearing – Qty 1
- BB Cup Spacer for 68mm MTN ONLY – Qty 1
- Sleeve (internal dust/moisture seal) – Qty 1
- RIGHT/DRIVE Cup with 30mm ID Bearing – Qty 1
- 30mm ID X 4mm Dust Cover – Qty 1
- 30mm ID X 6mm Dust Cover – Qty 1
Product Usage Instructions
Bottom Bracket Installation
-
* 1. Apply grease or anti-seize to the frame & BB cup threads.- Locate, read, and follow the directional arrows on the cups.
- Thread the Right/Drive cup into the frame’s Right/Drive side and torque to 40Nm with Praxis M30 Tool.
- Thread the Left/Non-Drive cup with the attached moisture seal into the frame’s Left/Non-Drive side and torque to 40Nm with Praxis M30 Tool.
- Lightly grease the underside of Dust Covers and place them over bearings with logos facing outward.
- Now you can install your crank following the Praxis Crank instructions at www.praxiscycles.com/manuals.
BB Dust Cover Setup
Refer to the next page for the Dust Cover Guide for the correct placement
of Dust Covers for your crank.
SAFETY INFORMATION – READ BEFORE THE RIDE
Since specific tools and experience are necessary for proper installation, it
is recommended that the product be installed by a qualified bicycle
technician.
Read the service instructions of your crank carefully before installing the
parts. Loose, worn or damaged parts may cause riding problems and serious
injury may occur as a result. If installation and adjustments are not carried
out correctly, the chain may come off and this may cause you to fall off the
bicycle which could result in serious injury. Read these instructions
carefully, and keep them for later use.
- Ensure that the frame shell is clean.
- Before riding the bicycle, check that there is no play or looseness in the bottom bracket connection. Be sure to retighten the crankarms and pedals at periodic intervals.
- If you feel any looseness or ‘play’ in the bearings, the bottom bracket should be inspected/replaced.
- Be sure to read the instructions for your front chainrings/crank in conjunction with these service instructions.
- Do not wash the bottom bracket with high-pressure jets of water.
- For maximum performance, it is required to remove and periodically inspect/clean your Praxis Works bottom bracket.
- Parts are not guaranteed against natural wear and tear resulting from normal use.
- For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle dealer or call Praxis Works.
- Praxis Works assumes no responsibility for damages or injury related to improperly installed components.
READ THE STEP-BY-STEP INSTRUCTIONS THAT ARE PROVIDED ON THE OTHER SIDE.
For the latest instructions and knowledge base updates:
https://praxiscycles.com/tech-docs/
WARRANTY
- Praxis Works Bottom Bracket products are warrantied to be free from defects in materials or workmanship for two years after the original purchase. The warranty is non-transferable and valid to the original purchaser of the product only.
- Any attempt to modify the product in any way such as drilling, grinding or painting will void the warranty.
- This warranty is not valid for “abused” or neglected products, or products that are damaged by improper installation.
- If a defect is found, our entire liability and your sole remedy shall be, at our option, free repair or replacement of the Praxis product.
- Except as expressly required by law, Praxis Works shall not be held liable for any indirect, special, or consequential damages.
THIS WRITTEN EXPRESS WARRANTY IS INSTEAD OF ALL OTHER WARRANTIES, IMPLIED OR EXPRESSED. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. For more information on warranty policy and instructions for completing a warranty claim, check out the Full Warranty Policy found on our website. www.praxis- works.com
M30-THRU BSA | Compatibility and Spec
CRANKSET| Compatible Praxis M30-THRU & other-brand cranks (30mm DRIVE/30mm
NON-DRIVE)
FRAME SHELL| BSA 68mm Road Frames | BSA 68/73mm MTN Frames
REQUIRED TOOLS
- One Praxis M30 BB Tool
- 3/8” Drive Torque Wrench
- Anti-Seize Compound
- Waterproof Grease
Included Parts
| Number | Part | Qty |
|---|---|---|
| 1. | 30mm ID X 1mm Dust Cover | 1 |
| 2. | 30mm ID X 2mm Dust Cover | 1 |
| 3. | LEFT/NON-DRIVE Cup with 30mm ID Bearing | 1 |
| 4. | BB Cup Spacer for 68mm MTN ONLY | 1 |
| 5. | Sleeve (internal dust/moisture seal) | 1 |
| 6. | BB Cup Spacer for 68mm MTN ONLY | 1 |
| 7. | RIGHT/DRIVE Cup with 30mm ID Bearing | 1 |
| 8. | 30mm ID X 2mm Dust Cover | 1 |
| 9. | 30mm ID X 4mm Dust Cover | 1 |
| 10. | 30mm ID X 6mm Dust Cover | 1 |
TOOLS REQUIRED
BOTTOM BRACKET INSTALLATION
BB DUST COVER SETUP
BB DUST COVER GUIDE
FAQ
- Q: Can I install the product myself?
- A: It is recommended that the product be installed by a qualified bicycle technician due to the specific tools and experience required for proper installation.
- Q: Where can I find warranty information?
- A: For more information on warranty policy and instructions for completing a warranty claim, visit www.praxis-works.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>