PRAXIS M24 MTN Crank Instruction Manual

PRAXIS M24 MTN Crank

SAFETY INFORMATION – READ BEFORE RIDE

Since specific tools and experience are necessary for proper installation, it is recommended that the product be installed by a qualified bicycle technician. Read these crank service instructions carefully before installing it. Loose, worn or damaged parts may cause riding problems and serious injury may occur as a result. If installation and adjustments are not performed correctly, the chain may come off and this may cause you to fall off the bicycle which could result in serious injury. Read these instructions
carefully, and keep them for later use.

• Be careful not to let your clothing get caught in the chain while riding, otherwise you may fall off the bicycle.
• Check that the chain tension is correct and that the chain is not damaged. If the tension is too weak or the chain is damaged, the chain should be replaced or else it may break and you may fall off the bicycle.
• Use a torque wrench to check the final tightening torque of the main crank bolt. Furthermore, after riding approximately 60 miles (100 km), use a torque wrench to re-check the tightening torques, including the chainring bolts. Main Crank bolt = Torque 48-52Nm. Chainring Bolts = Torque 8-10Nm.
• If the frame bottom bracket shell is not parallel, shifting performance will be affected and performance will drop.
•  Check that there are no cracks in the crankarms before riding the bicycle. If there are any cracks, the crankarm may break and you may fall off the bicycle.
• Before riding the bicycle, check that there is no play or looseness in the bottom bracket connection. Also, be sure to retighten the crank, chainring bolts, and pedals at periodic intervals.
• If you feel any looseness or ‘play’ in the bearings, the bottom bracket should be inspected/replaced.
• To ensure the designed performance, only use 10, 11 or 12 sp chains (for 12 sp use SRAM Eagle chain only).
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
•  For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle dealer or call Praxis Works.
• Praxis Works assumes no responsibility for damages or injury related to improperly installed components.

READ THE STEP BY STEP INSTALLATION INSTRUCTIONS PROVIDED ON THE OTHER SIDE.

WARRANTY

• Praxis Works products are warrantied to be free from defects in materials or workmanship for two years after original purchase. The warranty is non-transferable and valid to the original purchaser of the product only.
• Any attempt to modify the product in any way such as drilling, grinding or painting will void the warranty.
• This warranty is not valid for “abused” or neglected products, or products that are damaged by improper installation.
•  If a defect is found, our entire liability and your sole remedy shall be, at our option, free repair or replacement of the Praxis product.
•  Except as expressly required by law, Praxis Works shall not be held liable for any indirect, special, or consequential damages.

THIS WRITTEN EXPRESS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, IMPLIED OR EXPRESSED. This warranty gives you specific legal rights, and you may also have other rights which vary state to state. For more information on warranty policy and instructions for completing a warranty claim, check out the Full Warranty Policy found at our website. www.praxis-works.com

M24 MTN Direct Mount | Compatibility and Spec

BOTTOM BRACKET| M24 BBs – 73mm BSA, 73mm BB30/PF30, BB90/92
GEARING| 30, 32, 34, 36
CRANKARM LENGTH| 165, 170, 175
REQUIRED CRANK INSTALLATION TOOLS

T25 Torx wrench
8mm Allen wrench
Torque wrench

TORQUE SPECS

T25 Torx Bolts| 9 Nm
Main M24 Crank Bolt| 48-52 Nm

CRANK INSTALLATION

BEFORE YOU START, READ THIS:

•  Your Praxis M24 bottom bracket (sold separately) must be installed in frame
•  Use M24 BB Dust Covers and Wave Washer that came with M24 bottom bracket – SEE GUIDE ON LAST PAGE!
•  For M24 bottom bracket instructions : www.praxiscycles.com/manuals
  

1.  Grease Direct Mount Ring /Drive arm interface

2. Install ring on drive arm with 3 T-25 bolts

3. Torque bolts to 9Nm

4.  Grease the steel M24 spindle

5.  Slide Wave Washer onto spindle

6.  Slide the correct 24mm Dust Cover onto spindle (see guide)

7.  Verify Dust Cover Praxis logos face ring

ً

1.  Insert crank into Drive Side Cup

2. Push crank fully through bottom bracket

3.  Put correct 22mm Non-Drive Side Dust Cover onto spindle (see guide)

4.  Verify Dust Cover Praxis logos face outward

5.  Install Non-Drive Side arm with 8mm Allen wrench

6. Torque arm 8mm main bolt to 48-52Nm

7. Verify crank spins freely.

8.  Finished

SIMPLE CRANK REMOVAL
ONLY use an 8mm Allen wrench in the Non-Drive Side crankarm bolt. Turn wrench counterclockwise to loosen the bolt. After it loosens the resistance will increase, which is normal, as it is self-extracting. Keep turning to complete removal of crankarm. Once off, remove the crank from the frame.

CHAINLINE GUIDE

BB DUST COVER GUIDE “DM” = DIRECT MOUNT SPIDER (Removable Spider)
“NON-DM = NOT DIRECT MOUNT SPIDER (Pressed-On or integrated Spider)

References

• PRAXIS | Bicycle components for discerning riders like you.
• Technical Manuals | Praxis Works

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>