SUNJOE SPX8000-Pro 14.9A Electric Pressure Washer with Hose Holder Owner’s Manual

: June 5, 2024
: SUNJOE

SUNJOE SPX8000-Pro 14.9A Electric Pressure Washer with Hose Holder Owner’s Manual

IMPORTANT! Safety Instructions

All Operators Must Read These Instructions Before Use

WARNING! This indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION! This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

DANGER! This indicates a hazardous situation, which, if not followed, will result in death or serious injury

General Safety

WARNING! This appliance is not intended for use by children or by unassisted, unsupervised persons whose physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.

Before starting up your machine, please check it carefully for any defects. If you find any, do not start up your machine. Contact your authorized Snow Joe®

Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).

WARNING! When using the pressure washer, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. These include:

Know your product – Know how to stop the machine and bleed pressure quickly. Thoroughly familiarize yourself with the controls.
Keep bystanders away – All visitors and pets should be kept a safe distance away from the work area.
Use the right product – Do not use this machine for any job except that for which it is intended.
Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber gloves and non-slip footwear are recommended when working outdoors.
Slippery surfaces – Exercise caution to avoid slipping or falling. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.
Stay alert – Watch what you are doing. Use common sense. Do not operate the pressure washer when you are tired, or under the influence of alcohol or drugs.
Do not overreach – Keep proper footing and balance at all times.
Avoid unintentional starting – Do not carry a pluggedin machine with your finger on the trigger. Make sure the switch is off before plugging in the machine.
Do not abuse the cord – Never carry the machine by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.
Use safety glasses – Also use safety footwear, snug-fitting clothing, protective gloves, hearing and head protection.
Check the water temperature – This pressure washer is only meant to pump cold water. NEVER connect it to a hot water supply as it will significantly reduce the life of the pump.
Store indoors – NEVER store the pressure washer outdoors or where it could freeze. The pump could be seriously damaged.
Ground Fault Circuit Interrupter (GFCI) – This product is equipped with a ground fault circuit interrupter built into the power cord plug. If replacement of the plug or cord is required, use only identical replacement parts.
Inspect electrical cords – The insulation of the power cord should be perfectly intact. If the power cord is damaged or shows any signs of wear or tear, do not use the pressure washer. Contact your authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).

WARNING! Do not use this appliance without reading this instruction manual.

WARNING! This appliance has been designed for use with cleaning agents that are recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance.

WARNING! Do not use the appliance within range of persons unless they are wearing protective clothing.

WARNING! Risk of injection or injury – Do not direct discharge stream at persons.

WARNING! High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.

Do not direct the jet at yourself or others in order to clean clothes or footwear.
Disconnect the tool – Disconnect from the electrical power supply before performing any maintenance task.
Keep children away – This high-pressure electric power washer must not be used by children or untrained personnel.
To ensure safety, use only original replacement parts from the manufacturer or those approved by the manufacturer.

WARNING! Water that has flowed through backflow
preventers is considered to be non-potable.

WARNING! During cleaning, maintenance or when replacing parts, the machine must be disconnected from its power source by removing the plug from the socket outlet.

WARNING! High-pressure hoses, fittings, and couplings are important for the safe operation of the appliance.
Use only hoses, fittings, and couplings recommended by the manufacturer.

Check for damaged parts – Do not use the appliance if the supply cord or other important parts of the appliance are damaged (e.g. safety devices, high-pressure hoses, trigger gun).
This high-pressure electric power washer must not be used at temperatures below 32ºF (0°C).

WARNING! Power cords on drums should always be completely unwound to prevent the cord from overheating.

Power cord connections should be kept dry and off the ground.
If the power cord is damaged, do not use the appliance. Contact your authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).
Keep the machine on a stable, flat surface during operation, handling, transportation, and storage. Sudden overturn of the machine can cause bodily injury.
In the event of an accident or breakdown, switch off the machine immediately. (If contact with detergent occurs, rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: If there are problems with the electrical mains, short voltage drops may appear when starting the equipment.
This can, in turn, influence other equipment (e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM, such disturbances are not expected. (If you require assistance, contact your local supply authority for further information.)

WARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If you find any, do not start up your machine and contact your distributor.
The following should be observed when connecting the high-pressure electric power washer to the electric supply:

The electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to the earth exceeds 30 mA for 30 ms or a device that will interrupt the earth circuit (GFCI).

IMPORTANT

Only use water without any impurities. If there is a risk of running sand into the inlet water (i.e. from your own well), an additional filter should be installed.

Grounding Instruction

This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This unit is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER! Improper connection of the equipmentgrounded conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the unit. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adapter with this unit.

Safety Devices

The spray gun features a safety lock. When the lock is activated, the spray gun cannot be operated.

Thermal sensor – A thermal sensor protects the motor against overloading. If the thermal sensor is activated and the power is cut off, wait for a while until the motor is cool and restart the unit.
Ground fault circuit interrupter (GFCI) protection – This pressure washer is provided with a ground-fault circuit interrupter (GFCI) built into the plug of the power-supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection.
It is not recommended to use an extension cord with this pressure washer. The unit comes standard with a 35 ft GFCI power cord. Using an extension cord may cause a drop in line voltage resulting in loss of power and overheating.
Do not abuse the cord. Never pull the pressure washer by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.

WARNING! To reduce the risk of electrocution:

Inspect cord before using.
Do not use if cord is damaged.
Keep all connections dry and off the ground.
Do not touch plug with wet hands.
Keep cord away from heat and sharp edges.
Do not spray electrical apparatus and wiring.

Risk of explosion

Do not spray flammable liquids.
Do not use acids, bases, solvents, or any flammable material in this product. These substances can cause physical injuries to the operator and irreversible damage to the machine.

Additional safety instructions

High-pressure: keep clear of nozzle.
Injection hazard: equipment can cause serious injury if the spray penetrates the skin.
Do not point the gun at anyone or at any part of the body.
In case of skin penetration, seek medical aid immediately.
Before servicing, cleaning, or removing any parts, shut off the power and relieve pressure.
This machine is not suitable for connection to the potable water mains.

Product Description

Purpose

This electric high pressure washer is intended for residential use. It is designed for medium-to-heavy duty cleaning jobs on boats, motorcycles, RV’s, ATV’s, trailers, decks, barbecues, siding, patio furniture, and more.

Areas of application

Never use the machine in potentially explosive areas under any circumstances!
The operating temperature must be between 32ºF (0ºC) and 104ºF (40ºC).
The machine consists of an assembly with a pump, which is encased in a shock-absorbing housing. To provide the operator with an optimal working position, the machine is equipped with a spray wand and a non-slip handle grip, whose shape and configuration comply with applicable regulations.
Do not cover or modify the spray wand or the spray nozzle in any way.
The high-pressure electric power washer is designed to be used with cold water; higher temperatures can damage the pump.
Do not use water that is dirty, gritty, or contains any chemical products, as such impurities could impair operation and shorten the life of the machine.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.

Symbols	Descriptions	Symbols	Descriptions
READ THE OPERATOR’S MANUAL(S) – Read, understand, and follow

all instructions in the user manual(s) before attempting to assemble and operate.| | WARNING! Electrical shock hazard.
| SAFETY ALERT – Indicates a precaution, a warning, or a danger.| Safety Symbols | WARNING! Do not expose the unit to rain or wet conditions. Keep dry.
| WEAR EYE AND HEARING PROTECTION – For protection against injury, wear ear defenders and safety goggles.| | To reduce the risk of injury, user must keep all bystanders at least 49 ft (15 m) away.
| Wear safety gloves during use to protect hands.| Safety
Symbols | Wear non-slip footwear that will protect your feet and improve your footing on slippery surfaces.
| Store indoors. Never store the pressure washer outdoors.
If the pump freezes, permanent damage may occur.| | Machine not suitable for connection to the potable water mains.
| Always keep the power cable away from heat sources, oils, or sharp edges. Immediately remove plug from the mains if the cable is damaged, frayed, or entangled.| Safety Symbols | WARNING! Turn the machine OFF and disconnect it from the power supply before inspecting, cleaning, changing accessories, or conducting any other maintenance task.

Know Your Electric Pressure Washer

Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below to the unit in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Know Your Electric Pressure Washer

Trigger gun
Safety lock
High-pressure hose connection
Foam-volume knob
Foam spray nozzle
Foam cannon bottle
Power cord with GFCI
Water outlet (high pressure connection)
Wheels (x2)
High-pressure hose
Needle clean-out tool
Water inlet (garden hose connection)
Lower frame assembly
ON/OFF switch
Turbo nozzle
0º (red) & 25º (green) Quick-Connect nozzle
Trigger gun holder
Hose holder
Upper frame
Trigger
Foam grip

Technical Data

Rated Voltage 120V ~ 60 Hz
Brushless Induction Motor 14.9-amp
Max Water Inlet Temperature 104ºF (40ºC)
Max Water Inlet Pressure 0.7 MPa
Foam Cannon Capacity 33.8 fl oz (1 L)
Foam Cannon Spray Distance 11.5 ft (3.5 m)
High-pressure Hose Length 20 ft (6 m)
Max Pressure at initial discharge 3200 PSI
per CSA internal pressure testing
Rated Pressure under typical load 2500 PSI
Max Flow with nozzle open 1.3 GPM (4.9 L/min)
at minimum pressure
Rated Flow under typical load 1.1 GPM (4.2 L/min)
Power Cord Length 35 ft (10.7 m)
Net Weight 46.5 lbs (21.1 kg)

Unpacking

Carton Contents

Electric pressure washer with lower frame assembly
Upper frame
Upper frame panel
Stainless steel lance
Trigger gun
High-pressure hose
Wheels (x2)
0º (red) Quick-Connect nozzle
25º (green) Quick-Connect nozzle
Turbo nozzle
Hardware: washers (x4), cotter pins (x2), M6 machine screws (x2) and M6 nuts (x2)
Needle clean-out tool (included with manual packet)
Manual with registration card

Carefully remove the pressure washer and check to see that all of the above items are supplied.
Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, DO NOT return the unit to the store. Please call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging material until you are ready to use your new electric pressure washer. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.

IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a suffocation risk!

WARNING! Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury

Assembly

Place two washers on either side of the wheel spindle and insert the wheel axle into the spindle. (Fig. 1).
Fix the wheel by inserting the cotter pin into the hole on the end of the wheel shaft, as shown (Fig. 2).
Repeat the above steps for the other wheel.
Slide the upper frame into lower frame assembly. They snap together using springed loaded push buttons and require no screws (Fig. 3).
Attach the hose upper frame panel onto the front of the upper frame and secure it with the pair of machine screws and nuts (Fig. 4).
Install the foam cannon onto the back of the upper frame panel (Fig. 5).
Fit the lance into the trigger gun and rotate the collar until the two parts are completely locked (Fig. 6).
Connect the high-pressure hose to the trigger gun (Fig. 7).
Connect the other end of high-pressure hose to the water outlet of the pressure washer (Fig. 8).

WARNING! Keep hose away from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose.
Thread your garden hose (male end) into the water inlet (Fig. 9). The garden hose must have an internal diameter of at least 13 mm (1/2 in.) and must be reinforced. The water supply must be at least equal to the washer delivery capacity.
Attach the garden hose to a water supply (Fig. 10).

WARNING! Do not connect to potable water main.

WARNING! If connection is made to a potable water system, the system shall be protected against backflow.

WARNING! The intake water temperature must not exceed 104ºF/40ºC. The water supply must not exceed 0.7 MPa.

CAUTION! The washer must only be used with clean water; use of unfiltered water containing corrosive chemicals will damage the washer.

Operation

Using the Pressure Washer

IMPORTANT! This pressure washer is equipped with a micro-switch sensitive to water flow. This Total Stop System (TSS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The TSS then automatically turns the motor off to protect the pump from overheating, thus saving energy and prolonging pump life.

Position the washer as CLOSE as possible to the water supply.
The washer must be used on a secure and stable surface in a standing, upright position (Fig. 11).
Make sure the unit is switched off before plugging the unit into the power outlet.
Check that the electrical supply voltage (V) and frequency (Hz) correspond to those specified on the rating plate.
If the power supply is correct, you may now plug the pressure washer into the power outlet (Fig. 12).

NOTE: The GFCI may need to be reset when first plugged into the electric outlet. Press the “Reset” button until the power light indicator on the GFCI illuminates when plugged in.
Turn the water supply tap on completely.
Make sure the safety lock is stowed and in its original position (Fig. 13), then pull the trigger for a few seconds until water flow is steady. This will allow air to escape and discharge any residual pressure in the hose.
Turn the ON/OFF switch to the ON/I position to start the pressure washer (Fig. 14).
CAUTION! To prevent damage to the appliance, do not allow it to operate dry. Before starting the appliance, make sure that it has a stable supply of water.
When re-starting the pressure washer, always keep the trigger pressed.
NOTE: The pump only runs when the trigger is pulled and shuts off when the trigger is released.

Using Nozzles

Before beginning any cleaning task, determine the best nozzle for the job. Each of the nozzles has a different spray pattern.
25˚ (for all-purpose cleaning), 0˚ (for spot cleaning or hard-toreach areas) and the turbo nozzle (for heavy dirt and grime).

CAUTION! NEVER change nozzles without locking the safety lock on the trigger handle.

WARNING! High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.

This electric pressure washer is equipped with two QuickConnect nozzles that easily snap onto the Quick-Connect collar of the spray wand.

To use a Quick-Connect nozzle on the spray wand:

Turn off the pressure washer and shut off the water supply. Pull the trigger to release water pressure.
Engage the safety lock on the trigger handle by pushing down on the safety lock into the slot on the handle (Fig. 13).
Select the right nozzle for the job (Fig. 15):
The 0º intense-jet nozzle (red) is an extremely powerful nozzle that delivers a high-pressure, pencil-point jet stream. It is used to cut heavy dirt deposits in a small, concentrated area. It is ideal for dissolving stubborn substances, like tar and grease spots on concrete, or for removing caked mud from equipment. Use this nozzle to clean hard-to-reach areas including the façades of 2-story buildings or the undersides of lawn mowers and tractors.
NOTE: Care should be used when choosing the right nozzle to avoid permanently gouging wood or damaging fragile surfaces.
Use the 25º fan-tip nozzle (green) to clean home siding, brick patios, wood decks, driveways, or sidewalks. When using this nozzle, test a small area first to avoid surface damage.
The rotary turbo nozzle automatically spins a zero degree spray in a circle at high speed. The spinning water jet hits the surface area from multiple angles, quickly breaking down caked-on dirt and grime. The turbo nozzle can cut cleaning time by up to 40%.
Snap the desired nozzle onto the Quick-Connect collar until it clicks into place (Fig. 16).
To disconnect a nozzle from the spray wand, repeat steps 1 and 2, then pulling back on the Quick-Connect collar and pull out the nozzle.

WARNING! Do not make changes to the nozzle while the trigger is engaged. Doing so could result in damage to the pressure washer or injury to the user.

Working with Detergents

When cleaning with the pressure washer, some cleaning tasks can be solved with water alone, but for most tasks cleaning with detergent allows for more effective dirt removal.

WARNING! Use only detergents specifically designed for use with pressure washers, such as Sun Joe® HOUSE + DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER (SPX-APC1G). DO NOT USE household detergents, acids, alkaline solutions, bleaches, solvents, flammable material, or industrial grade solutions. These could damage the pressure washer.

Remove the foam spray nozzle, and fill the foam cannon bottle with detergent designed specifically for use with pressure washers (Fig. 17).
NOTE: Many detergents may require mixing prior to use. Prepare the cleaning solution as instructed on the solution bottle.
Recap the foam cannon bottle, and attach it to the trigger gun. Simply push to lock it onto the Quick-Connect collar on the end of the lance (Fig. 18).
Turn the foam-volume knob on the foam cannon to vary the amount of foam (Fig. 19).
Turn on the pressure washer. Pull the trigger to operate the unit. The liquid detergent will automatically mix with water and be discharged through the nozzle.
Apply detergent from the bottom to the top of the dry surface to be cleaned.
NOTE: Wetting the surface first is not recommended as it dilutes the detergent and reduces its cleaning ability.
CAUTION! Always test the detergent in an inconspicuous area before use.
Allow the detergent to remain on the surface for a short time before rinsing. Do not allow the detergent to dry on the surface.

CAUTION! Damage may occur to painted surfaces if the detergent is allowed to dry on the surface. Wash and rinse a small section at a time. Avoid working on hot surfaces or in direct sunlight.

Rinsing with the Pressure Washer

Turn off the pressure washer and shut off the water supply.
Pull the trigger to release water pressure.
Engage the safety lock on the trigger handle by pushing down on the safety lock into the slot on the handle (Fig. 13).
Pull back on the quick-connect collar and pull out the foam cannon to release it.
Snap the 25º fan-tip nozzle (green) onto the QuickConnect collar until it clicks into place (Fig. 16).
Start from the top and work your way down, making sure to overlap your strokes.

IMPORTANT! NEVER USE:

Bleach, chlorine products, and other corrosive chemicals
Solvents (e.g. paint thinners, gasoline, oils)
Tri-sodium phosphate products
Ammonia products
Acid-based products

These chemicals will harm the unit and will damage the cleaning surface.

Shutting down

Turn the switch to the OFF/0 position (Fig. 14) and unplug the power cord from the outlet.
Turn off the water source.
Hold the trigger to release water pressure.
Disconnect the garden hose from the water inlet on the unit.
Disconnect the high-pressure hose connection on the trigger gun handle.
Engage the safety lock on the trigger handle by pushing down on the safety lock into the slot on the handle (Fig. 13).

WARNING! Turn off the water supply and squeeze the trigger to depressurize the unit. Failure to do so could result in personal injury due to discharge of high-pressure water.

Taking a break

If you are taking a break of two minutes or more between cleaning tasks:

Engage the safety lock (Fig. 13).
Turn the switch to the OFF/0 position.
Unplug the power cord from the outlet.

Storage

CAUTION! Always store your electric pressure washer in a location where the temperature will not fall below 32ºF (0ºC). The pump in this machine is susceptible to permanent damage if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE WARRANTY.

Store the pressure washer indoors in a dry, covered area where it is not subject to adverse weather conditions.
It is important to store this product in a frost-free area.
Always empty water from the hoses and the pump before storing.

CAUTION! The use of a pump protector is recommended to prevent cold weather damage during storage over the winter months.

Winterizing + long-term storage

If you must store your pressure washer in a location wherethe temperature falls below 32ºF (0ºC), you can minimize the chance of damage to your machine by utilizing the following procedure:

Disconnect all water connections.
Turn on the pressure washer for a few seconds until the remaining water in the pump exits. Turn off immediately.
Do not allow the high-pressure hose to become kinked.
Operate the pressure washer with non-corrosive/non-toxic anti-freeze, a pump saver, or a pump protector before storing for the winter.

WARNING! Before reusing, completely flush the unitout with clear water. Anti-freeze products can damage paintwork, so you must ensure there is no anti-freeze left in the system before using it again.

Maintenance

CAUTION! Before working on the pressure washer, disconnect the plug from the power supply socket.

Filter and Nozzle Cleaning

To ensure good performance, periodically remove the filter and rinse with warm water to prevent any foreign matter from clogging the pump (Fig. 20)
Clean the nozzle with the needle clean-out tool provided (Fig. 21). Remove any dirt from the nozzle hole and rinse.

Disposal

Recycling the Pressure Washer

Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities.
Contact your local government agency for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leach into the groundwater and get into the food chain, damaging your health and well-being.

Service + Support

If your Sun Joe® SPX8000-PRO electric pressure washer requires service or maintenance, please call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).

Model + Serial Numbers

When contacting the company, reordering parts, or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.
Model + Serial Numbers

Troubleshooting

Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that its parts are in proper working order.
To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.

Problems	Possible Cause	Possible Solution
Machine refuses to start

Power failure/machine not plugged into a working receptacle.
Defective socket.
Defective extension cord.

|

Check to make sure machine is plugged into a working outlet.
Check the power cord and reset the GFCI.
Try a different outlet.
Try the unit without an extension cord.

Fluctuating pressure|

Pump sucking air.
Valves dirty, worn out, or stuck.
Pump seals worn out.

|

Check the hoses and connections are airtight.
Clean or replace valves/seals.
Please call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563) for assistance.

Machine stops|

Incorrect mains voltage.
Thermal protection activated.
Nozzle partially blocked.

|

Check that the mains voltage corresponds to specification on the model label.
Let the washer cool down for 5 minutes, then restart.
Clean the nozzle.

Machine pulsating|

Air in inlet hose.
Inadequate supply of mains water.
Nozzle partially blocked.
Water filter blocked.
Hose kinked.

|

Allow machine to run by holding the trigger until regular working pressure resumes.
Check that the water supply corresponds to the specifications required.
WARNING! Avoid using long, thin hoses (minimum 1/2 in. diameter).
Clean the nozzle.
Clean the water inlet filter.
Straighten out the hose to remove any kinks/blockages.

Machine often starts and stops by itself|

Pump/spray gun is leaking.
Trigger mechanism is broken.

|

Please call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563) for assistance.

Machine starts, but no water comes out|

Pump/hoses or accessories frozen.
No water supply.
Water inlet filter blocked.
Nozzle blocked.

|

Wait for pump/hoses or accessories to thaw.
Connect inlet water.
Clean the water inlet filter.
Clean the nozzle.

Optional Accessories

WARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

Accessories	Item	Model

Accessories | Sun Joe® House + Deck All-Purpose Pressure Washer Rated Concentrated Cleaner

Sun Joe® Premium Snow Foam Pressure Washer Rated Car Wash Soap + Cleaner

Sun Joe® All-Purpose Heavy Duty Pressure Washer Rated Cleaner + Degreaser

| SPX-HDC1G

SPX-FCS1G

SPX-APC1G

Accessories | 25-Foot Medium-duty Extension Hose for SPX Pressure Washer Series| SPX-25H
| Solid Brass Universal Quick-Connect Coupler (Garden Hose to Pressure Washer Adapter)| SPX-UQC

Sun Joe’s complete line of premium pressure washer accessories and attachments make it easy to get your dirty work done, and also help you get the most out of your model!
SHOP ONLINE now at sunjoe.com

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).

SNOW JOE® + SUN JOE® CUSTOMER PROMISE

ABOVE ALL ELSE , Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty (“Warranty”) for our Products.

OUR WARRANTY

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from unauthorized sellers. If your Product does not work or there’s an issue with a specific part that is covered by the terms of this Warranty, Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no charge, or (3) repair the Product. How cool is that!

This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE (1-866-766-9563), or by e-mailing us at help@snowjoe.com. Failure to register your Product will not diminish your warranty rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do not affect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563)

Logo