AVMATRIX SE1117 H.265/ H.264 SDI STREAMING ENCODER User Manual
- June 5, 2024
- AVMATRIX
Table of Contents
AVMATRIX -SE1117- H.265- H.264- SDI- STREAMING -ENCODER
USING THE UNIT SAFELY
Before using this unit, please read below warning and precautions which provide important information concerning the proper operation of the unit. Besides, to assure that you have gained a good grasp of every feature of your new unit, read below manual. This manual should be saved and kept on hand for further convenient reference.
Warning and Cautions
- To avoid falling or damage, please do not place this unit on an unstable cart, stand, or table.
- Operate unit only on the specified supply voltage.
- Disconnect power cord by connector only. Do not pull on cable portion.
- Do not place or drop heavy or sharp-edged objects on power cord. A damaged cord can cause fire or electrical shock hazards. Regularly check power cord for excessive wear or damage to avoid possible fire / electrical hazards.
- Ensure unit is always properly grounded to prevent electrical shock hazard.
- Do not operate unit in hazardous or potentially explosive atmospheres. Doing so could result in fire, explosion, or other dangerous results.
- Do not use this unit in or near water.
- Do not allow liquids, metal pieces, or other foreign materials to enter the unit.
- Handle with care to avoid shocks in transit. Shocks may cause malfunction. When you need to transport the unit, use the original packing materials, or alternate adequate packing.
- Do not remove covers, panels, casing, or access circuitry with power applied to the unit!Turn power off and disconnect power cord prior to removal. Internal servicing / adjustment of unit should only be performed by qualified personnel.
- Turn off the unit if an abnormality or malfunction occurs. Disconnect everything before moving the unit.
Note: due to constant effort to improve products and product features, specifications may change without notice.
BRIEF INTRODUCTION
Overview
SE1117 is a HD audio and video encoder which can encode and compress SDI video
and audio source into IP stream, and then transmit it to streaming media
server via network IP address to live broadcast on platforms like Facebook,
YouTube, Ustream, Twitch, Wowza etc.
Main Features
- 1×SDI input, 1×SDI loop out, 1×Analog audio input
- Supports H.265/ H.264 stream encode protocol, up to 1080p60hz
- Dual-stream (main stream and sub stream)
- RTSP, RTP, RTMPS, RTMP, HTTP, UDP, SRT, unicast and multicast
- Video and audio streaming or single audio streaming
- Image and text overlay
- Mirror image & upside-down image
- Live stream with no need for connecting a computer
**Interfaces
**
SPECIFICATIONS
OPERATIONS GUIDE
Network Configuration and Login
Connect the encoder to network via a network cable. The default IP address of
the encoder is 192.168.1.168. The encoder can auto obtain a new IP address
when it is using DHCP on the network,
Or disable DHCP and configure the encoder and computer’s network in the same
network segment. The default IP address as below.
- IP Address: 192.168.1.168
- Subnet Mask: 255.255.255.0
- Default Gateway: 192.168.1.1
- Visit encoder’s IP address 192.168.1.168 through an Internet browser to login the WEB page for setting up. The default Username is admin, and password is admin.
Management Web Page
The encoding settings can be set on the encoder management web page.
Language Settings
There are languages of Chinese (中文), Japanese (日本語) and English for option on
the top-right corner of the encoder management web page.
Device Status
The status of MAIN STREAM and SUB STREAM can be checked on the web page. And
we also can have a preview on the streaming video from PREVIEW
VIDEO.
Network Settings
The network can be set to dynamic IP (DHCP Enable) or static IP (DHCP
Disable). The default IP information can be checked in Pa
Main Stream Settings
The main stream can be set to mirror image and upside-down image from MAIN
PARAMETER tab. Configure main stream network protocol RTMP/ HTTP/
RTSP/UNICAST/ MULTICAST/ RTP/ SRT accordingly. Please note that only one of
HTTP/RTSP/ UNICAST/ MULTICAST/ RTP can be enable at same time.
Sub Stream Settings
Configure sub stream network protocol RTMP/ HTTP/ RTSP/ UNICAST/
MULTICAST/RTP/ SRT accordingly. Please note that only one of HTTP/ RTSP/
UNICAST/MULTICAST/ RTP can be enable at same time.
Audio and Extension
Audio Settings
The encoder support audio embedding from external analog input. Therefore, the
audio can be from SDI embedded audio or analog Line in audio. Besides, Audio
Encode Mode can be ACC/ MP3/ MP2.
OSD Overlay
The encoder can insert logo and text to the Main Stream / Sub Stream video at
same time. The logo file should be named logo.bmp and resolution below
1920×1080 as well as less than 1MB. Text content overlay support up to 255
characters. The size and color of the text can be set on the web page. And
user also can set the position and transparency of the logo and text
overlay.
Color Control
User can adjust the brightness, contrast, hue, saturation of streaming video
through the web page.
System Settings
User can set the encoder reboot after 0-200 hours for some
applications.
LIVE STREAM CONFIGURATION
Configure the encoder to live stream on platforms like YouTube, facebook, twitch, Periscope, etc. Following is an example to show how to configure the encoder to live stream on YouTube.
- Step 1. Set the main parameters of Stream Protocol to the H.264 mode, and other options are recommended to be the default configuration. In some occasion, they can be adjusted according to the actual situation. For example, if the network speed is slow, the Bitrate Control can be switched from CBR to VBR and adjust the Bitrate from 16 to 12000.
- Step 2. Setting the RTMP options as follow image:
- Step 3. Enter the stream URL and stream key in the RTMP URL, and connect them with”/”. For example, the stream URL is “rtmp://a.rtmp.youtube.com/live2”. The Stream key is “acbsddjfheruifghi”.
Then the RTMP URL will be “Stream URL”+ “/” + “Stream Key”:
“rtmp://a.rtmp.youtube.com/live2/acbsddjfheruifghi”. See below
image.
- Step 4. Click“Apply”to live stream on YouTube.