RIDGID R86211 18V OCTANE Brushless 1-2 in. High Torque 6-Mode Impact Wrench User Manual

: June 5, 2024
: RIDGID

Table of Contents

RIDGID R86211 18V OCTANE Brushless 1-2 in. High Torque 6-Mode Impact
GENERAL POWER TOOL SAFETY WARNINGS
IMPACT WRENCH SAFETY WARNINGS
SYMBOLS
FEATURES
ASSEMBLY
OPERATION
APPLICATIONS
DIRECTION OF ROTATION SELECTOR
INSTALLING/REMOVING BATTERY PACK
LED LIGHTS
INSTALLING AND REMOVING SOCKETS
OPERATING THE IMPACT WRENCH
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RIDGID R86211 18V OCTANE Brushless 1-2 in. High Torque 6-Mode Impact

Wrench

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Use this product only with batteries and chargers listed in tool/appliance/battery pack/charger correlation supplement 988000-302.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.
Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power tool in unexpected situations.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265°F may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

IMPACT WRENCH SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Know your power tool. Read operator’s manual care-fully. Learn its applications and limitations, as well as the specific potential hazards related to this power tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.
Always wear eye protection with side shields marked to comply with ANSI Z87.1 when assembling parts, operating the tool, or performing maintenance. Fol-lowing this rule will reduce the risk of serious personal injury.
Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.
Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an elec-trical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and pos-sibly injury.
Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.
Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.
Do not charge battery in a damp or wet location. Do not use, store, or charge battery packs or products in locations where the temperature is less than 50°F or more than 100°F. Do not store outside or in vehicles.
Under extreme usage or temperature conditions, bat-tery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of seri-ous personal injury.
Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL| SIGNAL| MEANING
| DANGER:| Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.
| WARNING:| Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
| CAUTION:| Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
| NOTICE :| (Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

Read Operator’s Manual

| To reduce the risk of injury, user must read and understand operator’s manual before using this product.
|

Eye Protection

| Always wear eye protection with side shields marked to comply with ANSI Z87.1.
|

Wet Conditions Alert

|

Do not expose to rain or use in damp locations.

|

Recycle Symbol

FEATURES

PRODUCT SPECIFICATIONS

SPEEDS
NO LOAD SPEED (1):…………………….0-600/min (RPM)
NO LOAD SPEED (2): …………………0-1,350/min (RPM)
NO LOAD SPEED (3): …………………0-1,850/min (RPM)
Anvil…………………………………………………………………1/2 in.
Impacts per minute (IPM)……………………………0-2,300/min
Max Fastening Torque………………………………..1,100 ft-lbs.
Max Breakaway Torque………………………………1,500 ft-lbs.

ASSEMBLY

WARNING:
Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled or with damaged or missing parts could result in serious personal injury.Do not attempt to modify this product or create ac-cessories or attachments not recommended for use with this product. Any such alteration or modifica-tion is misuse and could result in a hazardous con-dition leading to possible serious personal injury. If any parts are damaged or missing, please call 1-866-539-1710 for assistance.

OPERATION

WARNING:
Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. Always remove battery pack from the tool when you are assembling parts, making adjustments, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury. Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recom-mended can result in serious personal injury.

APPLICATIONS

You may use this tool for the purposes listed below:

Driving and removing nuts and bolts using an impact socket

HIGH-TEMPERATURE PROTECTION Li-ion battery packs are equipped with a high temperature protection feature that automatically deactivates the tool when it is overheated. To resume operation, allow the tool to cool and then squeeze the trigger.

OVERLOAD PROTECTION
When the tool is forced or the motor is overloaded, the tool will automatically shut off. To reset the tool, release the trigger and resume operation. If the tool still does not resume opera-tion, remove and reinsert the battery. Do not force the tool.

INSTALLING/REMOVING BELT HOOK

The belt hook may be installed on either side of the housing.

Align holes in belt hook with holes in the housing.
Install screws to secure belt hook in place.
To uninstall, remove screws then remove belt hook.

VARIABLE SPEED SWITCH TRIGGER

The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.
To turn the tool ON, depress the switch trigger. To turn it OFF, release the switch trigger and allow the anvil to come to a complete stop.
NOTE: A whistling or ringing noise coming from the switch during use is a normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

Set the direction of rotation selector in the OFF (center lock) position to lock the switch trigger and help prevent accidental starting when not in use.
Position the direction of rotation selector to the left of the switch trigger for forward operation. Position the selector to the right of the switch trigger to reverse the direction.
NOTE: The tool will not run unless the direction of rotation selector is pushed fully to the left or right.

WARNING:
Battery tools are always in operating condition. Lock the switch when not in use or carrying at your side, when installing or removing the battery pack, and when installing or removing sockets.

INSTALLING/REMOVING BATTERY PACK

Lock the switch trigger.
Insert the battery pack into the product as shown.
Make sure the latches on each side of the battery pack snap into place and that battery pack is secured in the product before beginning operation.
Depress the latches to remove the battery pack.

For complete charging instructions, see the operator’s manu-als for your battery pack and charger.

LED LIGHTS

The LED lights in the base illuminate upward when the switch trigger is depressed.
If the tool is not in use, the time-out feature will cause the light to start fading and then shut off.
The LED light illuminates only when there is a charged bat-tery pack in the tool.

INSTALLING AND REMOVING SOCKETS

Use only sockets designed for impact wrenches. Always select the correct size impact socket for nuts and bolts.

CAUTION:
Using the wrong size socket may damage the nut or bolt and cause the fastening torque to be inac-curate or inconsistent.

Remove the battery pack.
Push the socket onto the anvil until the friction ring locks it into place.
To remove the socket, pull it away from the anvil. NOTE: Sockets are not included with this tool.

MODE SELECTOR

This tool has six modes: three speeds (High, Medium and Low) and three auto-tightening modes. These modes work as follows:
The speed mode selector toggle button allows speed adjustments from high speed, medium speed and low speed. Each press of the speed mode selector toggle button will lower speed from HIGH
(3) to MEDIUM (2) and then to LOW (1). When pressed again, the speed will change back to HIGH.
NOTE: The speed can only be changed in this sequence.
Auto-Tightening offers protection from overtightening fasteners. It allows for greater control, reducing damage to fasteners and work surfaces.
There are three Auto-Tightening Modes for this tool: HIGH (H), MEDIUM (M), and LOW (L). Each Auto-Tightening Mode senses impacting and stops at approximate levels of tightness. They are activated through the speed selector by pressing AUTO.

CAUTION:
Overtightening fasteners may cause galling or breakage, so it is recommended to choose a mode that stops at half of the desired torque application and to finish the tightening with a reliable torque wrench.

NOTE: Torque-limiting devices are compatible with Auto-Tightening and are available to prevent overtightening. They can be purchased seperately at The Home Depot and other hardware stores.

OPERATING THE IMPACT WRENCH

Proper fastening torque may be determined by the kind of bolt, the size of the bolt or the material or the workpiece. It is helpful to perform a test operation to determine the proper fastening time for the nut or bolt you are using.

Hold the tool with one hand pointed straight at the nut or bolt.
Depress the switch and fasten for the proper fastening time.
Remove the impact wrench from the nut or bolt.
Check the torque with a torque wrench.

IMPACT TIME
Many variables exist that will cause the maximum torque to the fastener to vary considerably, including the size and threading of the fastener, lubrication, material hardness, and environmental conditions.

NOTICE:
After the head of a nut or bolt has seated, additional impacting will increase the chance of shearing bolts, nuts, sockets or tearing into wood.

ELECTRIC BRAKE
The electric brake will stop the socket rotation after the operator releases the switch trigger.