PROFICIENT VC60i Impedance Balancing Volume Control with Multiple Room Switch Owner’s Manual

June 5, 2024
PROFICIENT

PROFICIENT LOGO OWNER’S MANUAL
VC60i
Impedance Balancing Volume Control with Multiple Room Switch

INTRODUCTION

The VC60i is an impedance balancing wall-mounted stereo volume control, which connects between a pair of speakers and the speaker level output of an amplifier, receiver, or speaker selector.

PLACING THE VC60i

Before mounting the volume control into the wall, consider how it will be used. It is important to keep in mind the location of the primary listening area and the ease of running the wire to the location you choose. It is common to mount the volume control by the door as you walk into a room, next to existing wall fixtures, or in the primary area where you will be listening to music.
Do not place the volume control into the same box as a 110V AC circuit. (i.e. light switch, electrical outlet, etc.). Speaker wires can act as an “antenna” for electrical noise. Placing

WIRING THE VC60i

CAUTION

  • Please be sure that your amplifier or receiver is turned off prior to wiring the VC60i
  • Damage to your audio system may occur if the VC60i is not wired properly.

The VC60i features a quick and secure wire connecting system, which eliminates the need for turning small screws.
For best results, strip the speaker wire no more than 1 ⁄4″ from the end. Push the wire completely into the opening on the connector, then lift the lever using your finger or screwdriver. This will secure the wire. (see Figure 1)
If you need to remove the wire, simply push the lever down. This can be done with your finger, but it may be easier to use a screwdriver or similar tool. With the lever in the down position, you can pull the wire out.

PROFICIENT VC60i Impedance Balancing Volume Control with Multiple Room
Switch -

Add any number of speakers to your amplifier by making simple adjustments on the convenient front-mounted switch.
speaker wires too close to a light switch or dimmer may cause buzzing or popping sounds to be heard through the speakers. If you must locate the VC60i near electrical devices, use a separate electrical box.
Once the location has been determined, install a standard single-gang plaster ring, or a single gang electrical box (light switch type) before installing the VC60i.

Refer to Figure 2 when wiring the VC60i:

  1. Connect the amplifier or receiver’s left speaker output to the left amplifier terminals of the VC60i. Please observe the proper polarity of the connections (+ amplifier to + input on the VC60i).
  2. Repeat step 1 for the right side.
  3. Connect the wires from the left speaker to the left speaker output terminals of the VC60i. Please observe the proper polarity of the wires for the correct speaker phase (+ speaker to + output).
  4. Repeat step 3 for the right speaker connection.

CAUTION
If the input and output connections are reversed, the minimum setting on the VC60i would present a short across the amplifier or receiver output terminals, resulting in serious damage to your amplifier or receiver. Please double-check steps 1 – 4. The VC60i cannot be connected in series with another volume control.

PROFICIENT VC60i Impedance Balancing Volume Control with Multiple Room
Switch - Figure 2

SWITCH ADJUSTMENT FOR MULTIPLE SPEAKERS

The VC60i is designed to run multiple pairs of speakers without damaging your amplifier or receiver. The adjustment is made by using a switch that can be easily changed, even after the control is mounted into the wall.
Please follow the recommendations in this section carefully.
Failure to set the switch properly may result in damage to your amplifier or receiver.
The label next to the switch on the VC60i gives a minimum recommended setting for placing the switch according to how many speakers you will be attaching to the VC60i. However, to achieve the optimum performance you should follow the steps below:

  1. Determine the minimum recommended load that your amplifier or receiver can handle.
    • If it is 4Ω, use Chart A
    • If it is 8Ω, use Chart B

  2. How many 8Ω speakers will be attached to one channel (left or right) of the amplifier? Find the number under 8Ω on the chartyou are using.

  3. How many 4Ω speakers will be attached to one channel (left or right) of the amplifier? Find the number next to 4Ω on the chart you are using.

  4. Follow the column under the number of 8Ω speakers and the row next to the number of 4Ω speakers until they intersect. You will see a letter. Set the switch to this letter.

Example:

  1. The amplifier states it can safely power 4Ω. Use Chart A.
  2. There is one 8Ω speaker. Find 1 under the 8Ω columns on the chart.
  3. There are three 4Ω speakers. Find 3 next to the 4 ohm rows on the chart.
  4. The column and the row intersect at “B”.
  5. Set the switch to “B”.

CHART A
(Use when amplifier can safely power 4Ω)

PROFICIENT VC60i Impedance Balancing Volume Control with Multiple Room
Switch - CHART A CHART B
(Use when amplifier can safely power 8Ω)PROFICIENT VC60i Impedance Balancing
Volume Control with Multiple Room Switch - CHART B

MOUNTING THE VC60i

Once the VC60i has been wired, it is ready to be mounted into the wall. Referring to Figure 3, place the components of the control into the wall In the order illustrated. Use the enclosed screws to hold the components in place.
NOTE: The rotary switch is shipped with the control turned as far counterclockwise as it will turn (off). If you have changed this, return it to the fully counterclockwise position before starting the installation.

PROFICIENT VC60i Impedance Balancing Volume Control with Multiple Room
Switch - Figure 3

LIMITED TEN-YEAR WARRANTY

Proficient Audio Systems warrants to the original retail purchaser only that this product will be free from defects in materials and workmanship for a period of ten years, provided the speaker was purchased from a Proficient Audio Systems Authorized Dealer. Defective products must be shipped, prepaid and insured, together with proof of purchase, to the Proficient Audio Systems Authorized Dealer from whom they were purchased, or to Proficient Audio Systems at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit is to be borne by the purchaser. If upon examination at the Factory or Proficient Audio Systems Authorized Dealer, it is determined that the unit was defective in materials or workmanship at any time during this warranty period, Proficient Audio Systems or the Proficient Audio Systems Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below. If this model is no longer available and can not be repaired effectively, Proficient Audio Systems, at its sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If mounting surface modification is required, Proficient Audio Systems assumes no responsibility or liability for such modification. All replaced parts and products become the property of Proficient Audio Systems. Products replaced or repaired under this Warranty will be returned to the original retail purchaser, within a reasonable time, with freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair, or modification of the product which has not been authorized or approved by Proficient Audio Systems. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions.
This warranty will be void if the Serial Number on the product has been removed, tampered with, or defaced. This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will Proficient Audio Systems be liable for any incidental or consequential damages arising out of the use or inability to use the product, even if Proficient Audio Systems. or a Proficient Audio Systems Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitations on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.

DWG • 516-933-4900dwgdistribution.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PROFICIENT User Manuals

Related Manuals