makita FS6300 Drywall Screwdriver Instruction Manual

Drywall Screwdriver
INSTRUCTION MANUAL

FS6300 Drywall Screwdriver

|
---|---

Explanation of general view

SPECIFICATIONS

Model| FS4000| FS4200| FS4300/
FS4300A| FS6300/
FS6300A| FS6300R
---|---|---|---|---|---
Capacities| Self-drilling screw| 6 mm| 6 mm| 6 mm| –| –
Drywall screw| 5mm| 5mm| 5mm| 4mm| 4mm
No load speed (min 1)| 0 – 4,000| 0 – 4,000| 0 – 4,000| 0 – 6,000| 0 – 6,000
Overall length| 269 mm| 269 mm| 279 mm| 279 mm| 279 mm
Net weight| 1.3 kg| 1.4 kg| 1.4 kg| 1.4 kg| 1.4 kg
Safety class| /II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003

Intended use
The tool is intended for screw driving in wood, metal, and plastic.
Power supply
The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on a single-phase AC supply. They are double-insulated in accordance with European Standards and can, therefore, also be used from sockets without earth wire.
For European countries only
Noise
The typical A-weighted noise level determined according to EN60745:
Sound pressure level (LpA) : 82 dB(A)
Sound power level (LWA) : 93 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined according to EN60745:
Work mode: screw-driving without impact Vibration emission (ah) : 2.5 m/s 2 or less Uncertainty (K) : 1.5 m/s 2
EC Declaration of Conformity
We Makita Corporation as the responsible manufacturer declares that the following Makita machine(s):
Designation of Machine: Drywall Screwdriver Model No./ Type:
FS4000,FS4200,FS4300,FS6300,FS6300R are of series production and
Conforms to the following European Directives: 98/37/EC until December 28th, 2009, and then with 2006/42/EC from 29th December 2009
And are manufactured in accordance with the following  standards or standardized documents: EN50144, EN60745
The technical documentation is kept by our authorized representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
10 th September 2008

Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to screwdriver safety rules. If you use this power tool unsafely or incorrectly, you can suffer serious personal injury.

1. Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring or its own cord. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
2. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immediately after the operation; they may be extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.
WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and unplugged before adjusting or checking the function on the tool.

Depth adjustment
Fig.1
The depth can be adjusted by turning the lock ring. Turn it in “B” direction for less depth and in “A” direction for more depth. One full turn of the lock ring equals 1.5 mm change in depth.
Adjust the lock ring so that the distance between the tip of the locator and the screw head is approximately 1 mm as shown in the figures. Drive a trial screw into your material or a piece of duplicate material. If the depth is still not suitable for the screw, continue adjusting until you obtain the proper depth setting.
Fig.2
Fig.3
Switch action
Fig.4
CAUTION:

• Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then push in the lock button.
To stop the tool from the locked position, pull the switch trigger fully, then release it.
NOTE:

• Even with the switch on and motor running, the bit will not rotate until you fit the point of the bit in the screw head and apply forward pressure to engage the clutch.

Lighting up the lamps
For Model
FS4200,FS4300,FS4300A,FS6300,FS6300A,FS6300R
Fig.5
CAUTION:

• Do not look in the light or see the source of light directly.
  To turn on the lamp, pull the trigger. Release the trigger to turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of the lamp.
  Be careful not to scratch the lens of the lamp, or it may lower the illumination.

Reversing switch action
Fig.6
CAUTION:

• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
  This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the →position (A side) for clockwise rotation or the↔ position (B side) for counterclockwise rotation.

Hook
Fig.7
The hook is convenient for temporarily hanging the tool.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
  Installing or removing the bit
  To remove the bit, first remove the locator by pulling the lock ring away from the gear housing..

Fig.8
Grasp the bit with a pair of pliers and pull the bit out of the magnetic bit holder. Sometimes, it helps to wiggle the bit with the pliers as you pull.
To install the bit, push it firmly into the magnetic bit holder. Then install the locator by pushing it firmly back onto the gear housing.

Fig.9
Installing a removable cord adapter
For Model FS6300R
Fig.10
Insert the Removable Cord Adapter as far as it goes so that the marking on an end of the Removable Cord Adapter on the side of connecting to the power supply cord is aligned to the marking on the other end of the Removable Cord Adapter on the side of connecting to the tool.
Turn the Removable Cord Adapter clockwise until it is locked with a lock button.
Fig.11
And at this time the marking on the end of the Removable Cord Adapter on the side of the power supply cord is aligned to the marking on the other end of the Removable Cord Adapter on the side of connecting to the tool.
Fig.12
Removing the removable cord adapter
Fig.13
Rotate the Removable Cord Adapter counterclockwise until it stops while pressing the lower part of the lock button.
Then pull the Removable Cord Adapter in that position.
Fig.14
Use of locator holder
Fig.15
The locator can be temporarily held on the locator holder during replacing bit or using without locator. To hold the locator, position the trapezoidal holes of the locator on the swells of the locator holder and push it in.

OPERATION

Fig.16
Fit the screw on the point of the bit and place the point of the screw on the surface of the workpiece to be fastened. Apply pressure to the tool and start it. Withdraw the tool
as soon as the clutch cuts in. Then release the switch trigger.

CAUTION:

• When fitting the screw onto the point of the bit, be careful not to push in on the screw. If the screw is pushed in, the clutch will engage and the screw will rotate suddenly. This could damage a workpiece or cause an injury.
• Make sure that the bit is inserted straight in the screw head, or the screw and/or bit may be damaged.
• Hold the tool only by the handle when performing an operation. Do not touch the metal part.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and unplugged before attempting to perform an inspection or maintenance.
  To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by
  Makita Authorized Service Centers, always using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
• Phillips Insert bits
• Magnetic bit holder
• Locator
• Plastic carrying case

Makita Corporation Anjo, Aichi, Japan
884894A984

Documents / Resources

| makita FS6300 Drywall Screwdriver [pdf] Instruction Manual
FS6300 Drywall Screwdriver, FS6300, Drywall Screwdriver, Screwdriver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>