Bol TS-Wp10 Bathroom Clock IP65 Waterproof User Manual

Bol TS-Wp10 Bathroom Clock IP65 Waterproof

Meanings of display:

• Time display mode
• Countdown display mode

Buttons

Thank you for purchasing the TS-WP10 bathroom clock. The user’s guide for operations is given as follows:

Major functions:

• Hour, minute, second, temperature, humidity, and simulated time are displayed on the same screen
• Two-alarm clocks Snooze function: Five minutes by default Countdown function
• Dynamic countdown progress bar indicator
• Dynamic seconds countdown indicator
• Indoor temperature (measuring range: 0°C~50°C/32°F~122°F); refreshing interval: 30s. Resolution: 0.1°C.
• Indoor humidity (measuring range: 20%~99%); refreshing interval: 30s. Resolution: 1%.
• Max./Min. values of indoor temperature/humidity
• Set up beyond-limit values of indoor temperature/humidity
• Backlight color prompt for beyond-limit temperature/Humidity Temperature/Humidity calibration function
  Waterproof grade: IPX4

Power supply:

1. Power supply through USB DC power cable(when the DC cable is plugged in, the backlight indicator turns on for 8 seconds, and then automatically dies out if no buttons are pressed. To keep the backlight indicator constantly on, long press [CLEAR] for at east 2 seconds until the beep sound is heard, and then enable Always On of the backlight indicator. To disable Always On of the backlight indicator, long-press [CLEAR] for at least 2 seconds until the beep sound is heard, and then disable Always On. During the countdown and alarming periods, the backlight indicator is always on, regardless of whether the DC cable is plugged in or not.
2. Powered by 3 AAA batteries (the clock is not always on when powered by batteries).
   Remarks: This clock is shipped without batteries.

Power on and reset:

When this clock is powered on, the LED is fully displayed for 3 seconds, and the backlight color alternates in the order of red, orange, and white for one cycle. The initial interface of the system is displayed after a beep sound.

Default display after startup: white backlight Time: 0:00
Default time format: 24 hours Default units: Temperature [°C]; relative humidity: [%]

Time settings:

In the time display mode, jump to the setup page by long pressing [MODE], when the parameters to be set up are displayed and flashing; the setup sequence is: 12HR/24HR→hour→minute→exit and return to normal time display. In time settings, short press [＋] if you want to add the value by 1 or long-press [＋] for quick increase (8 steps/s); short press [－] if you want to decrease the value
by 1, or long-press [－] for quick decrease (8 steps/s).

Alarm clock settings:

In the time display mode, short pressing [MODE] results in a switch to the alarm clock display interface. The switching sequence is: Normal time display→ Alarm Clock 1→Alarm Clock 2→Normal time display.

In the alarm clock review mode, the alarm clock can be turned on or off by short pressing [＋]. During setting, select 1 alarm clock and long-press [MODE] for at least 3 seconds, when the Hour place starts flashing; then short press [MODE] and the Minute place starts flashing. Short press [＋] if you want to increase the value by 1, or long-press [＋] for quick increase (8 steps/s); short press 【－】 if you want to decrease the value by 1, or long-press [－] for quick decrease (8 steps/s). Short press [MODE] to automatically save settings and exit.

Snooze mode:

When the alarm clock is ringing, short press [CLEAR] if you want to go to the 5-minute snooze mode, or any other button to silence the alarm clock.

Countdown settings:

In the countdown mode, the numbers of the current time show the minute and second countdown values, and the second point is fixed without flashing (but the MS and the sandglass flash once every second as prompt). In the simulation section, the outer ring shows seconds, and the inner ring is the dynamic progress circle of the entire countdown. When the countdown hits zero, both the outer ring and inner ring disappear. The innermost round spot flashes. Meanwhile, the numbers show 00:00 and flash accordingly.

In the time display mode:

1. Short press [10] to set up the countdown duration. Every pressing within 3 seconds increases the duration by 10 minutes. The longest duration allowed is 99 minutes.
2. Short press [1] to set up the countdown duration. Every pressing within 3 seconds increases the duration by 1 minute. The longest duration allowed is 99 minutes.
3. Short press the [10] , and then long-press the [10] , press a multiple of 10 minutes to quickly accumulate the countdown time, up to 99 minutes.
4. Short press the [1] , then long-press the [1] , and press 2 steps/ second to quickly accumulate the countdown time minute by minute, up to 99 minutes.
5. During time settings, short press [CLEAR] anytime if you want to clear and exit from the countdown settings.
6. If no action takes place within 3 seconds after a countdown is set up, the countdown automatically starts after a beep sound.
7. When countdown settings are ongoing, the time display shows the countdown duration, and the MS and sandglass symbols (not flashing) are displayed at the upper left corner.
8. When a countdown is in action, short press [CLEAR] anytime if you want to clear and exit from the countdown mode, when the clock will give a beep sound.
9. When the countdown hits zero, the clock gives intermittent beep sounds that will stop after 2 minutes if no action is taken. Short pressing any button can stop the beep sound anytime.
   Attention: If you choose to set up another function when a countdown is in action, the clock shows the setup interface of this function. However, if no action takes place within 3 seconds, the clock automatically goes back to the countdown display interface. When the countdown hits zero, the clock gives beep sound for 2 minutes as prompt. If any button is pressed during this period, the beep sound stops and the clock returns to the normal time display interface. If no button is pressed after the beep sound lasts for 2 minutes, the clock automatically returns to the normal time display interface.

Upper/Lower temperature/humidity alarm settings:

In the time display mode, short press [ALERT] to turn on or off the temperature/humidity alarm function. In the time display mode, long press [ALERT] if you want to set up the temperature/humidity alarm. In this setting mode, short press [＋] if you want to increase the value by 1, or long-press [＋] for quick increase (8 steps/s); short press[－] if you want to decrease the value by 1, or long press [－] for quick decrease (8 steps/s). The setting sequence is: upper limit of temperature alarm (red backlight alert)→lower limit of temperature alarm (orange backlight alert)→upper limit of humidity alarm (red backlight alert)→lower limit of humidity alarm (orange backlight alert) →Exit.

When the temperature or humidity alarm conditions are triggered, the corresponding alerting color is displayed, and the clock gives beep sound for 5 seconds. The corresponding alarm icon keeps flashing until the triggering conditions no longer exist. If no action is taken, the corresponding alerting color is displayed every minute, accompanied by the beep sound that lasts for 5 seconds. Pressing any button can silence the alarm.
Note : The default temperature limits are 50°C and 0°C; the default humidity limits are 99% and 20%. In temperature settings, the value increases by 0.1 each time; in humidity settings, the value increases by 1 each time.

Temperature/Humidity calibration function:

In the time display mode, press down [MODE] and [＋] simultaneously to go to the temperature value calibration mode; in this mode, short press [＋] if you want to increase the temperature by 0.1°C, or long press [＋] for quick increase (8 steps/s); short press [－] if you want to decrease the temperature by 0.1°C, or long press [－]for a quick decrease (8 steps/s). After temperature settings are complete, press [MODE] to go to the humidity value calibration mode. In this mode, short press [＋] if you want to increase the humidity value by 1, or long-press [＋] for quick increase (8 steps/s); short press [－] if you want to decrease the humidity value by 1, or long-press [－] for quick decrease (8 steps/s). After humidity settings are complete, press [MODE] to confirm the settings and exit from the setting mode.

[＋] button functions:

In the normal time display mode (no settings are ongoing), short press this button if you want to view the MAX/MIN values of temperature/humidity.
In the MAX/MIN temperature/humidity value review mode (no settings are ongoing), long-press this button if you want to clear the recorded MAX/MIN values of temperature/humidity.
In the alarm clock viewing mode (no settings are ongoing), short press this button if you want to turn on/off the alarm clock. In the setting mode, short/long press this button if you want to increase values by one step or several steps.

[－] button functions:

In the normal time display mode (no settings are ongoing), short press this button if you want to switch the temperature unit between °C and °F.
In the setting mode, short/long press this button if you want to decrease values by one step or several steps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>