PRINCESS 350 Smart Infrared Panel Heater Instruction Manual

: June 5, 2024
: Princess

Table of Contents

PRINCESS 350 Smart Infrared Panel Heater
SAFETY
PARTS DESCRIPTION
INSTALLATION
BEFORE THE FIRST USE
Display
Technical Specification
CLEANING AND MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PRINCESS 350 Smart Infrared Panel Heater

PRINCESS-350-Smart-Infrared-Panel-Heater-product

SAFETY

By ignoring the safety instructions the manufacturer cannot be held responsible for the damage.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Never move the appliance by pulling the cord and make sure the cord cannot become entangled.
The appliance must be placed on a stable, level surface.
The user must not leave the device unattended while it is connected to the supply.
This appliance is only to be used for household purposes and only for the purpose it is made for.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
To protect yourself against an electric shock, do not immerse the cord, plug or appliance in the water or any other liquid.
WARNING: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
Joists, beams and rafters shall not be cut or notched to install the appliance.
Please do not install the appliance close to curtains and other combustible materials. This could cause a fire.
The appliance shall, under no circumstances, be covered with insulating material or similar material.
The heater must not be located immediately below a socket-outlet.
Do not use this heater if it has been dropped.
WARNING : The heater must not be used if the glass panels are damaged.
Use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
WARNING : To reduce the risk of fire, keep textiles, curtain, or any other flammable material a minimum distance of 1m from the air outlet.
The heater needs to be installed so that the switches and other controls cannot be touched by a person in the bath or shower.

PARTS DESCRIPTION

On / Off switch
Display
On/off button
WiFi button
+ button
– button
Timer button
Heating indicator
Wall bracket
Heater
Feet

INSTALLATION

Wall mounting

Please note that the product must be installed at least 15 cm from the floor and 50 cm from the ceiling.
The heater must be mounted at 4 points, ensure there is a 300mm clearance on all sides of the heater.
Measure the distance between the centre of each bracket both horizontally and vertically to ensure drilling holes in the correct place. Mark the positions of the 4 holes to be drilled on the wall (1), use the supplied wall mount drawings for correct measures
Drill the holes in the wall (2), then insert the plastic expanded plugs (3) and screw the 4 supplied screws into the plastic expanded plugs (4).
Attached the panel heater onto the screws and move the heater to the left so that the screws drop into the securing slots (5).

Foot assembly

If the heater is not mounted on the wall, the supplied feet must be fitted to the unit.
To fix the feet, remove the bottom screws from the heater housing.
Place the feet and secure them by putting the screws back into the housing.
Take care to ensure that the feet are located correctly on the bottom end of the heater

BEFORE THE FIRST USE

Put the power cable into the socket. (Note: Make sure the voltage which is indicated on the device matches the local voltage before connectingthe device. Voltage 220V-240V 50/60Hz)
When the device is turned on for the first time, a slight odour will occur. This is normal, ensure adequate ventilation. This fragrance is only temporary and will disappear soon.
During heating up and cooling down there may be some noises caused by the heater casing expanding and contracting, this is normal and does not indicate any fault.

Display

When the red on/off switch is off, the display screen is also off.
When power is on (on/off switch is on), and the machine is in stand-by mode, the display screen is off, only when the device is already connected to Wi-Fi, the display screen is off with only the Wi-Fi icon visible.
Pressing the on/off touch button when the power is on will show the Wi- Fi icon + current temperature + time (if set on the phone) on the display screen with back ground light on.
After 10 seconds without pressing one of the touch buttons, the back ground light will go off. On screen you will still see: Wi-Fi icon + current temperature + time (if set on the phone)

USING THE HEATER WITH CLIMATE APP
The heater can be used manually with its built-in controls or you can use a smart phone or smart speaker to control it. Before you begin, ensure the Homewizard Climate app is downloaded. The Homewizard Climate app is available on Android and iOS.

Open HomeWizard Climate APP.
Create an account or if you already have a HomeWizard account, please log in using those details.
Click “Add new Climate Device” to add a new device.
Select the device you wanted to connect.
Follow the instructions on the app to connect the heater.
To control your device with voice using a smart speaker please refer to the manufacturer’s instructions on how to enable a skill through your device.

Technical Specification

Wireless technology: Wi-Fi
Operating frequency: 2.4 GHz
Max. radio-frequency power: 20.5 dBm

CLEANING AND MAINTENANCE

Before cleaning, unplug the appliance and wait for the appliance to cool down.
Clean the appliance with a damp cloth. Never use harsh and abrasive cleaners, scouring pad or steel wool, which damages the device.

ENVIRONMENT
This appliance should not be put into the domestic garbage at the end of its durability, but must be offered at a central point for the recycling of electric and electronic domestic appliances. This symbol on the appliance, instruction manual and packaging puts your attention to this important issue. The materials used in this appliance can be recycled. By recycling of used domestic appliances you contribute an important push to the protection of our environment. Ask your local authorities for information regarding the point of recollection.

Support
You can find all available information and spare parts at www.princesshome.eu!