Trotec TRH 27 E Oil-Filled Radiator Instruction Manual

Trotec TRH 27 E Oil-Filled Radiator

INSTRUCTIONS

Symbols

Warning of electrical voltage
This symbol indicates dangers to the life and health of persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of persons due to hot surface.
Warning
This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the operating manual must be observed.

Safety

Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use.

Warning
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
This appliance can be used by children aged
from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Warning
Children of less than 3 years should be kept away from the device unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
Warning

• Do not use the device in small rooms if persons are present who cannot leave the room independently and who are not under constant supervision.
• Do not use the device in potentially explosive rooms or areas and do not install it there.
• Do not use the device in an aggressive atmosphere.
• Only put up the device in an upright, stable position on firm ground.
• Let the device dry out after a wet clean. Do not operate it when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover the device during operation.
• Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.
• Do not sit on the device.
• This appliance is not a toy. Keep away from children and animals. Do not leave the device unattended during operation.
• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
• The mains connection must correspond to the specifications in the Technical annex.
• Insert the mains plug into a properly fused mains socket.
• Observe the device’s power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload.
• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from the mains socket when the device is not in use.
• Do not under any circumstances use the device if you detect damages on the mains plug or power cable.
• If the power cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Defective power cables pose a serious health risk!
• The power cable must not rest on the device or run in front of the air outlet, otherwise it may be damaged as a result of high temperatures.
• When installing the device, observe the minimum distances from walls and other objects as well as the storage and operating conditions according to the technical data (chapter Technical annex).
• Keep a safety distance of at least 1 m between the device’s air outlet and all combustible materials such as textiles, curtains, beds and sofas.
• Make sure that the air outlet is not obstructed.
• Do not place the device on combustible ground.
• Only use original spare parts, for otherwise safe and functional operation cannot be ensured.
• Allow the device to cool down before transport and/or maintenance work.
• Do not use this device near bathtubs, shower trays, swimming pools or other water containers. Risk of electric shock!
• The device must not be positioned directly beneath a wall socket.
• The device must be set up in a way that the switches and controllers cannot be touched by a person in a bathtub or shower.
• Do not use the device if it has been dropped or if it shows visible signs of damage.

Intended use
The device is only suitable for well insulated spaces or occasional use.
The device is only intended to be used as additional heating device in dry, closed rooms whilst adhering to the technical data. For intended use it must only be positioned on the ground.

Foreseeable misuse

• Do not place the device on wet or flooded ground.

• Do not place any objects, e.g. clothing, on the device.

• Do not use this device in the vicinity of fuel, solvents, varnishes or other easily inflammable vapours or in rooms where these substances are stored.

• Do not use the device out of doors.

• Do not use the device for heating vehicles.

• The device must not be used near swimming pools.

• Do not use this device in the immediate vicinity of sinks, bathtubs or other water containers.
  Never immerse the device in water.

• Never heat rooms with a cubature of less than 4 m³. Risk of overheating!

• Any use other than the intended use is regarded as a reasonably foreseeable misuse.

• Please bear in mind that our devices are not designed for the application in business, craft or industrial enterprises. We do not accept any liability if the device is used in business, craft or industrial enterprises as well as for similar applications.

• Do not make any unauthorised modifications, alterations or structural changes to the device.

Personnel qualifications
People who use this device must:

• be aware of the dangers that occur when working with electric devices in damp areas.
• have read and understood the operating manual, especially the Safety chapter.

Maintenance tasks which require the housing to be opened must only be carried out by specialist electrical companies or by Trotec.

Symbols on the device

This symbol located on the device indicates that it is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device.
In order to avoid overheating and fire hazards, the heater must not be covered.

Residual risks

Warning of electrical voltage
Work on the electrical components must only be carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug from the mains socket!
Do not touch the mains plug with wet or damp hands. Hold onto the mains plug while pulling the power cable out of the mains socket.
Warning of hot surface
Parts of this appliance can become very hot and cause burns. Particular attention is to be paid when there are children or vulnerable persons present!
Warning
Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way!Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may use it as a dangerous toy.
Warning
Improper installation entails a risk of fire.
Do not place the device on combustible ground.
Do not place the device on high-pile carpets.
Warning
In order to avoid overheating and fire hazards, the device must not be covered!

Behaviour in the event of an emergency

1. Switch the device off.
2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.
3. Do not reconnect a defective device to the mains.

Overheating protection
The device is provided with a safety thermostat which is activated by overheating of the device (when exceeding the operating temperature).
Investigate the cause of overheating.
If the safety thermostat does not switch in the event of overheating, the overheating protection will be tripped. In that case the device switches off completely. If so, please contact the customer service to have the overheating protection replaced.

Tilt protection
The device comes equipped with a tilt protection. The tilt protection is a safety device intended to minimize the risk of fire in case the device is tipped over inadvertently. The device will be switched off when knocked over (or if its upright position is changed in any other manner).
The tilt protection switches the device off when it is inclined by a few degrees out of its vertical position. The device can again be used as usual only a few seconds after placing it back in vertical position and on solid ground.

Information about the device

Device description
The oil-filled radiator TRH 27 E is used to generate warm air for interior spaces.
The TRH 27 E comes with 3 power levels of up to 2,500 W.
The heat electrically generated by the heating elements within the device is absorbed by the heating medium oil. The heating medium oil offers the advantages of quick heat-up and long-term heat storage capacity. On these grounds the heating medium oil can guarantee a continuous heat emission. The radiator’s 11 fins increase the heat radiating surface and so enhance its effectiveness.
The device is further equipped with an overheating protection and a tilt protection.
Device depiction

Transport and storage

Note
If you store or transport the device improperly, the device may be damaged.
Note the information regarding transport and storage of the device.

Transport
To make the device easier to transport, it is fitted with wheels. To make the device easier to transport, it is fitted with a carry handle.
Before transporting the device, observe the following:

• Switch the device off.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not use the power cable to drag the device.
• Allow the device to cool down sufficiently.

Storage
Before storing the device, proceed as follows:

• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Allow the device to cool down sufficiently.

When the device is not being used, observe the following storage conditions:

• dry and protected from frost and heat
•  in an upright position where it is protected from dust and direct sunlight
• with a cover to protect it from invasive dust, if necessary
• Place no further devices or objects on top of the device to prevent it from being damaged.

Assembly and start-up

Scope of delivery

• 1 x Oil-filled radiator
• 2 x Foot with 2 castors each
• 1 x Cable holder
• 1 x Screw
• 1 x Manual

Unpacking the device

1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.

Assembly

Mounting the feet
The castors on the feet are already preassembled.

1. Place the device upside down on a scratch-proof, even surface and in a stable position.
2. Place the left foot upside down on the left side of the device.
3. Fasten the left foot with a screw.
4. Place the right foot with the slots upside down on the last two fins on the right side of the device.
5. Close the four clips of the right foot.
6. Turn the device over and set it down on the castors.
   ð Check the feet and castors for tight fit. The feet should rest evenly on the fins to ensure the upright position of the device.

Start-up

Info
Odours might arise upon initial start-up or after a longer period of non-use.

When positioning the device, observe the minimum distance from walls or other objects as described in the chapter Technical annex.

• Before restarting the device, check the condition of the power cable. If there are doubts as to the sound condition, contact the customer service.
• The device may only be operated when fully assembled and set up in a vertical position on a stable surface. Operation on instable ground is prohibited.
• Do not create tripping hazards when laying the power cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• Make sure that no curtains or other objects interfere with the air flow.
• Do not position the device directly below a wall socket.
• Make sure that the device cannot come into contact with moisture or water.

Connecting the power cable

• Insert the mains plug into a properly fused mains socket.
• Make sure that the power cable is guided along the back of the device. Never guide the power cable along the front of the device!

Operation

Avoid open doors and windows.
Operating elements

Switch power level on and off
6| Rotary switch of the room thermostat
7| power level flip switch 1200 W (together with flip switch 5 = 2500 W) Switch power level on and off

Switching the device on

1. Plug the device into a sufficiently fused socket.
2. Set the power level flip switch (5 or 7) to I to select the desired performance.
   ð You can actuate one flip switch to activate
   the 1200 W (7) or 1300 W (5) power level, or both for the 2500 W maximum power level.
   ð If the power level flip switch (5 or 7) is in position I, the flip switch is illuminated.

Setting the room thermostat

1. Select the desired temperature level via the infinitely variable rotary switch of the room thermostat (6).
   ð The heating switches off automatically upon reaching the set temperature. If the temperature falls below the set temperature, the heating switches back on.

To find the ideal thermostat setting, please proceed as follows:

1. Set the rotary switch of the room thermostat (6) to the highest level.
   ð As soon as the desired temperature has been reached, slowly turn the rotary switch of the room thermostat back until the power level flip switch (5 and 7) is no longer illuminated.
   ð The device now automatically maintains the desired temperature level.

Automatic temperature control via the room thermostat

• Upon reaching the maximum operating temperature of the heating medium in performance level 3 the device reduces its performance to level 2.
• When falling below the maximum operating temperature of the heating medium in performance level 3, the heating will automatically switch back over to level 3.
• When the device is set to performance level 1 or performance level 2, the operating temperature of the heating medium will not be controlled automatically. Upon reaching the preselected room temperature, the device switches off completely.

Frost monitor function
The device is equipped with a frost monitor function that prevents the room temperature from falling below the frost protection temperature. Please proceed as follows to activate the frost monitor function:

1. Set the power level flip switch (7) to position I.
   ð The power level flip switch (7) is illuminated.

2. Turn the infinitely variable rotary switch of the room thermostat (6) to the – position.
   ð In this position, the room thermostat switches on the heating automatically if the room temperature drops below the frost protection temperature.

Shutdown

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.

1. Switch off the device by setting the power level flip switch (5) and the power level flip switch (7) to the 0 position.
2. Hold onto the mains plug while pulling the power cable out of the mains socket.
3. Allow the device to cool down sufficiently.
4. Clean the device according to the Maintenance chapter.
5. Store the device according to the Storage chapter.

Errors and faults

Warning of electrical voltage
Tasks which require the device to be opened must only be carried out by authorised specialist companies or by Trotec.

The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device makes noises after switch-on:

• The heating medium oil expands due to heating. This is what causes the noise. It is a perfectly normal process. No measures are required.

The device does not start:

• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Check the room temperature. The room thermostat may have switched off, because the desired room temperature has been reached.
• Check whether the device is standing upright and on level ground. The tilt protection may have been tripped owing to the fact that the device was knocked over. Always put up the device in an upright position on a suitable, sufficiently dimensioned surface.
• The room thermostat might be defective. Have a defective room thermostat replaced by a specialist electrical company.
• Check whether the overheating protection has tripped (see chapter Safety).
• Wait for 10 minutes before restarting the device. If the device is not starting, have the electrics checked by a specialist company or by Trotec.

The device is switched on, but the heating is not operating:

• Check the room temperature. The room thermostat may have switched off, because the desired room temperature has been reached.
• Check whether the overheating protection has tripped (see chapter Safety).
• The heating resistor might have blown. Have a defective heating resistor replaced by a specialist electrical company.
• The room thermostat might be defective. Have a defective room thermostat replaced by a specialist electrical company.

Note
Wait for at least 10 minutes after maintenance and repair work. Only then switch the device back on.

The device still does not operate correctly after these checks:
Please contact the customer service. If necessary, bring the device to an authorised specialist electrical company or to Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.

• Switch the device off.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Allow the device to cool down completely.

Warning of electrical voltage
Tasks which require the device to be opened must only be carried out by authorised specialist companies or by Trotec.
Note
The device is filled with the heating medium oil. Tasks which require the oil tank to be opened must only be carried out by Trotec. In case of oil leakage please contact the customer service.

Cleaning the housing

Warning of electrical voltage
Never immerse the device in water!

Clean the housing with a soft, damp and lint-free cloth. Make sure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.

Technical annex

Technical data

100 cm

100 cm

100 cm

100 cm

top (A):

rear (B):

sides (C):

front (D):

Weight| 10 kg

Information requirements for electrical local space heaters

Heat output
Nominal heat output Pnom| 2.1 kW
Minimum heat output (indicative) Pmin| 1.2 kW
Maximum continuous heat output Pmax,c| 2.1 kW
Auxiliary electricity consumption
At nominal heat output elmax| NA
At minimum heat output elmin| NA
In standby mode elsb| NA
Only for electric storage local space heaters: Type of heat input (please select one option)
Manual heat charge control, with integrated thermostat| NA
Manual heat charge control with room and/or outdoor temperature feedback| NA
Electronic heat charge control with room and/or outdoor temperature feedback| NA
Fan assisted heat output| NA
Type of heat output/room temperature control (please select one option)
Single-stage heat output, no room temperature control| NO
Two or more manually adjustable stages, no room temperature control| NO
With mechanic thermostat room temperature control| YES
With electronic room temperature control| NO
With electronic room temperature control plus day timer| NO
With electronic room temperature control plus week timer| NO
Other control options (multiple answers possible)
Room temperature control, with presence detection| NO
Room temperature control, with open window detection| NO
With remote control option| NO
With adaptive start control| NO
With working time limitation| NO
With black bulb sensor| NO
Contact details| Trotec GmbH Grebbener Straße 7 D-52525 Heinsberg

Disposal

The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. You can also find out about other return options that apply for many EU countries on the website
https://hub.trotec.com/?id=45090. Otherwise, please contact an official recycling centre for electronic and electrical equipment authorised for your country.
The separate collection of waste electrical and electronic equipment aims to enable the re-use, recycling and other forms of recovery of waste equipment as well as to prevent negative effects for the environment and human health caused by the disposal of hazardous substances potentially contained in the equipment.

Heating medium oil
The heating medium oil must be drained from the device and collected.
The heating medium oil is to be disposed of according to the national regulations.

Trotec GmbH Grebbener Str. 7

D- 52525 Heinsberg
PHONE: + 49 2452 962-400
+ 49 2452 962-200

info@trotec.com
www.trotec.com

References

• The Trotec Group: best conditions for your success - TROTEC
• WEEE-Annahmestellen | Interzero - zero waste solutions
• Oil-filled radiator TRH 27 E - TROTEC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>