Chongqing Qinchengxing Technology L5-i Wireless Camera Video Auto Dolly User Manual

Chongqing Qinchengxing Technology L5-i Wireless Camera Video Auto Dolly User Manual

Product Analysis

Product Parameter

Maximum load-bearing range: 3KG| Maximum speed: 10cm/s speed adjustable, speed 0%-100% optional
---|---
Life time: 4 H| APP remote control distance: 8M (without interference, maximum)
Body battery charging time: about 3H| Built-in battery capacity: 1800mAh

The instructions for Indicator light display

Normal working state: display green light.
Charging status: display red light. Fully charged state: red light off.
Insufficient battery state: the battery is less than 10%, the red light flashes for 60 seconds to shut down, the indicator light is off.

APP Interface Description

Instructions

1. Scan the QR code to download the APP according to your mobile phone system. After the download is complete, you can proceed to the next step.

2. Press and hold the power button on the main unit for 2 seconds to turn it on, and the indicator light will be green.

3. Open the mobile phone Bluetooth, then open the mobile APP software, click to find the device, when the device list appears L5-i, click connect.

4. After the connection is successful, enter the video mode interface and click the AB point to set (the arrow in the figure below indicates).

5. Enter the AB point setting interface, forward rotation and reverse rotation are the driving direction selection of the car, first confirm the position of point A, click ‘point A positioning completed” after confirmation, and then select point B positioning, click after confirmation B point positioning is complete”, ‘positioning complete” will be displayed in red to indicate that the positioning of point AB has been completed, click to enter the next step.

6. D. Enter the video mode and time-lapse photography mode interface, click to select according to your needs, as shown in the figure below.

7. Video mode operation steps (as shown below)

Single cycle mode operation:

Single cycle button: Left and right direction key selection, refers to the one-way shooting from point A to point B or point B to point A. You can press the pause button to stop in the middle, and press the direction button to continue.
Shutter button: After the camera and the car are connected with a shutter release cable. You can control the camera to take pictures on the APP.

7. Click the icon”Delay Model” enter the delay mode:After setting the parameters,click the start button to start shooting; B—A button: start from point B; A—B button:start shooting from point A.  

Features

1. Mobile APP control, support Android, Apple download.
2. Free choice of AB point positioning and shooting.
3. Support video automatic loop shooting without frequent operation.
4. Support time-lapse photography shooting, parameter custom selection.
5. Can shoot in straight or curved lines.
6. It can be used with a ball head to shoot at low, tilt, and multiple angles.
7. Built-in lithium battery, support type-c interface charging.
8. The power is displayed in real time, and the speed is adjustable from 0-100.
9. Using stepping motor, precise control and low noise.
10. The maximum load-bearing capacity is 3KG, and it supports mobile phones, micro-singles, video recorders, etc., and there is no restriction on models.
11. The APP’s shutter button supports most mirrorless cameras.

Precautions

1. Do not turn the driving wheel forcefully.
2. It should not exceed the 3KG load-bearing range.
3. Do not use on non-flat surfaces.
4. The center of gravity must be adjusted and the shooting machine must be fixed before turning it on for use.
5. Please adjust the angle within the scale range, if it exceeds the range , will affect the running effect.
6. Please use this product in the correct way, as shown below:

Packing List

1. Autodolly 1PCS
2. Hex wrench 1PCS
3. TYPE-C charging cable 1PCS
4. Mutual screw 1PCS
5. Manual 1PCS
6. Rubber ring (large) 1PCS

FCC warning

1. This device should be installed and operated with minimum distance 20cm between the radiator&your body.
2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
3. This device may not cause harmful interference, and
4. This device must accept any interference received, including interference that may cause undesired operation.
5. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
6. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
7. Reorient or relocate the receiving antenna.
8. Increase the separation between the equipment and receiver.
9. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
10. Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>