hama 00 050560 Multifunction Laminator Instruction Manual

hama 00 050560 Multifunction Laminator

Machine setup

1. Laminate output (rear)
2. Roller unlocking (rear)
3. Connection cable
4. Laminate intake
5. On/Off switch
6. Ready status LED
7. Power status LED
8. Cutting ruler
9. Cutting head
10. Guide rail
11. Corner rounder
12. Collecting bin

Introduction

Foreword
Thank you for choosing Hama product. Take your time and read the following instructions and information completely.Please keep these instructions in asafe place for futurereference. If you sell the device, please pass these operating instructions on to the new owner.

Note –Importance of the operating instructions
Failure to observe the operating instructions when using the product constitutes incorrect use or wilful misuse and is not permitted.

Explanation of warning symbols and notes

Risk of electric shock
This symbol indicates arisk of electric shock from touching product parts carrying hazardous voltage.

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note
This symbol is used to indicate additional information or important notes.

Package contents

• “Basic DIN A4 /230” Laminator
• 20laminating pouches (5 xDIN A4, 5xDIN A5, 5xDIN A6, 5 business cards)
• Cutting ruler
• Corner rounder
• These operating instructions

Security

Correct use

• This product is intended for private, non-commercial use only.
• Do not operate the product continuously,asitisnot designed for this.
• Use the product only for the intended purpose.
• The product is intended only for use inside buildings.
• Protect the product from dirt, moistureand overheating and use it in dry rooms only.
• Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
• Do not use the product in adamp environment and avoid splashing water.
• Do not operate the product outside the power limits specified in the technical data.
• Do not use the product in areas in which electronic products arenot permitted.
• Do not drop the product and do not expose it to any major shocks.
• This product is not intended for use by persons, including children, with limited physical, sensory or mental abilities or lacking in experience or knowledge, unless they are supervised by aperson responsible for their safety or have been instructed on how to use the product.
• As with all electrical products, this device should be kept out of the reach of children.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
• Dispose of packaging material immediately in accordance with the locally applicable regulations.
• Do not modify the product in any way.Doing so voids the warranty.
• Only use the article under moderate climatic conditions.

Note
The product is only intended for volumes generated by households.

Basic safety instructions
Please note the following safety instructions in order to use the device safely:

• Check the device before use for any visible external damage. Do not put damaged device into operation.
• People who, as a result of their physical, mental or motor capacities, are unable to operate the device safely must only use the device under supervision or after instruction by a responsible person.
• Faulty components must only be replaced with original spareparts. Only these parts are guaranteed to meet the required safety standards.
• Protect the device against moisture and the penetration of liquids or objects. In the event of contact with liquid, disconnect the device from the power supply immediately.

Warning -Danger of burns on the housing
Do not touch the housing.

Risk of electric shock

• Do not open the device or continue to operate it if it becomes damaged.
• Do not use the product if the AC adapter,adapter cable or power cable is damaged.
• Do not attempt to service or repair the product yourself.Leave any and all service work to qualified experts.

Installation /Setup

Warning

• Only operate the product from asocket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
• Disconnect the product from the power supply using the On/Off switch –ifthis is not available, unplug the power cord from the socket.
• If using an amulti-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
• If you will not be using the product for a prolonged period, disconnect it from mains power.

Note

• Set the product up on alevel, horizontal and sufficiently stable and heat-resistant surface.
• Route all cables so that thereisnorisk of tripping.
• Do not bend or crush the cable.
• Protect the connecting cable from hot surfaces and sharp edges.
• Always pull directly on the plug when disconnecting the cable, never on the cable itself.
• The product must only be operated on asupply network as described on the type plate.
• Connect the network cable to aproperly installed and easily accessible network socket.

Operation

Note

• Always set the correct temperature for the laminating pouch thickness being used.
• When laminating thicker paper or multiple pages, we recommend using a thinner pouch.
• Always wait until one laminating operation is finished before starting the next one.
• Do not allow the device to run for more than two hours at a time.
• Wait around 15 seconds between two laminating processes.
• Laminating pouches of all sizes should be introduced into the centre of the opening on the front. Ensure that the sealed end is introduced first. (See Fig. 2)

Switching the device on

• Move the On/Off switch (5) to the “ON” position to switch the device on.
• The Power status LED (7) lights up solid red.
• The device now heats up automatically to the temperature required for laminating pouches.

Hot lamination

Warning – Danger of burns on the housing

• Do not touch the housing.
• Be aware that laminated objects are hot.
• Place the laminated object on a level surface to cool down in order to prevent it from curling up.

Note
Special pouches are needed for hot lamination. They are sealed using heat. This seal is permanent and cannot be undone. Only objects that are insensitive to heat should be laminated. From apouch edge of around 4mm, the objects are protected so they are virtually waterproof.The thickness of the pouch determines the object’s stability /kink protection.

• The Ready LED (6) lights up solid green once the required temperature has been reached.
• Place the object to be laminated in the corresponding hot lamination pouch.
• Guide the pouch into the middle of the front opening (4) on the device. Ensurethat the sealed end (see Fig. 2) is introduced first.
• The document is output again at the back (1).
• If the document has not been fully laminated, repeat the initial steps.
• To interrupt the lamination process (e.g. if the intake angle is incorrect), press the roller unlocking button (2) and correct the position of the pouch.

Switching the device off

• Move the On/Off switch (5) to the “OFF” position to switch the device off.
• Both status LEDs (6/7) go out.
• Remove the mains lead from the socket.
• Allow the device to cool down completely before tidying it away.

Accessories

Warning -Risk of burns

• Be aware that the cutting tools were only designed to cut paper and laminated documents.
• When using them, take careful to put fingers in the cutting area.
• Keep children away from the cutting tools.

Using the cutting ruler

• This kit includes a cutting ruler (8) that allows paper as well as laminating pouches to be easily cut to size.
• Set the cutting ruler (8) up on alevel, horizontal and stable surface.
• Push the cutting head (9) to one side of the guide rail.
• Place the document to be cut under the guide rail (10) and push it downwards.
• Pull the cutting head (9) along the guide rail (10) to the other side of the cutting ruler.
• Remove the cut material.

Using the corner rounder

• This kit includes a corner rounder (11) to round off the corners of paper and laminated documents.
• Set the corner rounder (11) up on alevel, horizontal and stable surface.
• Place one corner of the document to be trimmed in the opening of the corner rounder.
• Press the upper half of the corner rounder downwards.
• A handy collecting bin (12) catches the left-over paper.

Care and maintenance

Danger –risk of death from electric shock
Disconnect the mains plug from the socket before starting any cleaning work.

Warning -Danger of burns on the housing
Do not touch the housing.

Warning -damage to the device from moisture
Ensure, when cleaning, that no moisture penetrates the device in order to avoid irreparable damage to it.

The rollers on the laminator must be regularly cleared of dust and any glue residue. To do so, proceed as follows:

• Switch the device on -as described in 4.1 Switching the device on.
• Wait until the Ready status LED (6) lights up solid green
• Guide apiece of paper into the middle of the front opening (4).
• Repeat the process if there is lot of dirt on the paper.
• Clean the outside of the device with aslightly damp cloth.

Troubleshooting

The Power LED (7) does not light up solid red.

| The On/Off switch (5) is in the “OFF” position.| Move the On/Off switch

(5) to the “ON” position.

The mains cable (3) is not connected correctly.

| Ensure that the mains plug is in the mains socket.
The socket is not live.| Check the domestic fuses.
The device is faulty.| Notify Customer Services.

Pouches are not laminated correctly.

| ****

The required temperature has not yet been reached.

| Wait until the Ready status LED (6) lights up solid green.

Technical data

Warranty Disclaimer

All of the technical information, data and instructions regarding operation contained in these operating instructions was up to date at the time of printing and is provided based on previous experience and to the best of our knowledge. Hama GmbH &CoKG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

References

• hama.com
• Recycling Information hama.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>