ZIRCON M40 MetalliScanner Electronic Metal Detector Instructions

ZIRCON M40 MetalliScanner Electronic Metal Detector

PRODUCT OVERVIEW

The MetalliScanner®m40 electronic metal detector locates metal through concrete and most nonmetallic materials. The wide and pinpoint scanning positions allow you to quickly and easily find plumbing, ductwork, rebar, nails, and screws in your walls, floors, and ceilings. Find studs in lath and plaster walls by locating the row of nails attaching the wood lath to the studs. MetalliScanner®m40 is also great for scanning reclaimed or recycled lumber to find hidden metal before sawing and planing.

WIDE AREA SCANNING

1. Grasp the tool with your thumb over the power button.
2. Hold the tool in the air with the blue sensor parallel to the scanning surface away from any known metal.
3. Press and hold power button. The READY light indicates that calibration is complete and you are ready to search for metal.
4. Move the unit near the surface and scan while continuing to hold the power button. Do not rotate the tool, see Tip #3.
5. As you approach a metal object the red LEDs will light progressively from the bottom up. The closer the illuminated lights get to the top, the closer you are to a metal object. The illuminated blue sensor and audio tone indicate a strong target. Small targets or targets deep within the surface may only illuminate some of the red LEDs and not the blue sensor or audio tone. In this case, use the highest LED indication to determine the metal position.
6. Mark the point where you get the highest LED indication, continue scanning, and mark the point where the LED indication decreases. Halfway between these points is the logical center of the metal field. To further refine this position, see Tip #1.

PINPOINT SCANNING

1. Grasp the tool with your index finger over power button.
2. Hold the tool in the air with the blue sensor perpendicular to the scanning surface away from any known metal.
3. Press and hold power button. The READY light indicates that calibration is complete and you are ready to search for metal.
4. Move the unit near the surface and scan while continuing to hold the power button. Do not rotate the tool, see Tip #3.
5. As you approach a metal object the red LEDs will light progressively from the bottom up. The closer the illuminated lights get to the top, the closer you are to a metal object. The illuminated blue sensor and audio tone indicate a strong target. Small targets or targets deep within the surface may only illuminate some of the red LEDs and not the blue sensor or audio tone. In this case, use the highest LED indication to determine the metal position.
6. Mark the point where you get the highest LED indication; continue scanning and mark the point where the LED indication decreases. Halfway between these points is the logical center of the metal field. To further refine this position, see Tip #1.
7. Scan the surface both vertically and horizontally to pinpoint the metal target location.

LOCATING STUDS IN LATH & PLASTER

1. Scan across the wall using the Wide Area Scanning procedure outlined previously to locate the nails that attach the wood lath to the studs.
2. To help confirm you have found a stud and not a pipe or other metal object, scan the target area located in Step #1 again, this time using Pinpoint Scanning, and scan the area vertically. The LEDs may move up and down on the display, indicating the nail pattern of the small nails attaching the wood lath to the stud. (In contrast, a pipe or other solid metal will typically be indicated by a consistent signal.)
3. To help verify your findings, scan your work area thoroughly and mark the location of every object indicated by the tool. Do not assume everything is a stud.
   • Studs are normally spaced 16 in. (40 cm) or 24 in. (60 cm) apart, not odd intervals.
   • Studs normally run from floor to ceiling, except above and below windows, and above doors.
   • Pipes and other large metal objects will give a consistent, strong signal in either scanning mode. The nails in a stud will likely show some variance in the strength of the signal.
   • Be aware of walls that are likely to contain plumbing. For example, a living room wall may be common to a bathroom and contain plumbing for the sink, shower, or toilet.

Tips:

1. If the unit indicates metal over a large area, you can refine the scanning area to more accurately locate the metal target. After scanning the area as indicated above, mark the edges of the area where you get the strongest metal signal. Starting over one of the marks, press and hold the power button; this will recalibrate the tool and decrease the sensitivity. While holding the power button, scan the area again. The area indicated should become smaller so you can more precisely identify the metal location. This procedure can be repeated to narrow the field even further.
2. Because the unit uses signal strength to determine position, large, deep objects, and small, shallow objects will give similar indications.
3. The unit should be turned on in the same orientation that will be used when scanning. If the tool is twisted or rotated during use, you may get a temporary indication of metal where none is present. Wait until ONLY the READY light is on before scanning.
4. MetalliScanner®m40 finds ferrous (magnetic) metal such as 1/2 in. (12 mm) rebar to 4 in. (102 mm) deep and non-ferrous (non-magnetic) metal such as 1/2 in. (12 mm) copper pipe up to 2 in. (51 mm) deep. Targets found at the maximum depth may only be indicated by the first red LED on the display.
5. When scanning concrete, the tool will indicate the presence of the metal mesh that is usually found in driveways and slab foundations, but due to the size variety of metal mesh, the tool may not indicate the exact location of the wires.
6. Magnetized materials may cause false, unstable indications.

CHANGING THE BATTERY

1. Remove the battery cover located below the power button by pressing in on the arrow and sliding the cover towards the bottom of the tool.
   

2. Holding the tool upside down, tilt the battery out of the cavity.
   

Visitwww.zircon.com/support for the most current instructions.

LIMITED 1 YEAR WARRANTY
Zircon Corporation, (“Zircon”) warrants this product to be free from defects in materials and workmanship for one year from the date of purchase. Any in- warranty defective product returned to Zircon*, freight prepaid with proof of purchase date and $5.00 to cover postage and handling, will be repaired or replaced at Zircon’s option. This warranty is limited to the electronic circuitry and original case of the product and specifically excludes damage caused by abuse, unreasonable use or neglect. This warranty is in lieu of all other warranties, express or implied, and no other representations or claims of any nature shall bind or obligate Zircon. Any implied warranties applicable to this product are limited to the one year period following its purchase. IN NO EVENT WILL ZIRCON BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM POSSESSION, USE OR MALFUNCTION OF THIS PRODUCT.

In accordance with government regulations, you are advised that: (i) some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of incidental or consequential damages, so the above limitations and/or exclusions may not apply to you, and further (ii) this warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Return product freight prepaid with proof of purchase date (dated sales receipt) and $5.00 to cover postage and handling, to:

Zircon Corporation
*Attn: Returns Department 1580 Dell Avenue Campbell, CA 95008-6992 USA

Be sure to include your name and return address. Out of warranty service and repair, where proof of purchase is not provided, shall be returned with repairs charged C.O.D. Allow 4 to 6 weeks for delivery.

E-mail: info@zircon.com

Patent Pending
©2007 Zircon Corporation · P/N 62515 Rev A 08/07

MetalliScanner and Zircon are registered trademarks or trademarks of Zircon Corporation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>