BAUHN H3 LED Projector User Manual

BAUHN H3 LED Projector

BAUHN H3 LED Projector

Pack contents ⁄ Device parts

1. Mini projector
   

2. Electric cable

3. Remote control

4. AV cable
   

5. Lens cleaning fabric
   

General information

Reading and storing the user manual

Read this manual thoroughly before first use, even if you are familiar with this type of appliance. The safety precautions enclosed reduce the risk of fire, electric shock and injury when correctly adhered to.
Keep the manual in a safe place for future reference, along with the completed warranty card, purchase receipt and box. If applicable, pass these instructions on to the next owner of the appliance.

Explanation of symbols

The following symbols and signal words are used in this user manual, on the LED projector or on the packaging.

DANGER!

This signal word designates a hazard with a high degree of risk which will result in death or severe injury if not avoided.

WARNING!

This signal word designates a hazard with a moderate risk which will result in death or severe injury if not avoided.

CAUTION!

This signal word designates a hazard with a low risk, which may result in minor or moderate injury if not avoided.

NOTICE

This signal symbol/word warns of possible damage to property.

This symbol provides you with useful additional information on handling and use.

Safety instructions

Proper use

The LED projector is intended for private use and not suitable for commercial purposes. Only use the LED projector as described in this user manual. Any other use is considered improper and may result in damage to property. The manufacturer or vendor cannot be held liable for damages incurred through improper or incorrect use.

WARNING!:A person who has not read and understood all operating and safety instructions is not qualified to operate this appliance. All users of this appliance must read and understand this Instruction Manual before operating or cleaning this appliance. When using electrical appliances, basic safety precautions should always be followed, including:

1. Read all instructions before operating this appliance.
2. This appliance is NOT A TOY.
3. Unsupervised young children and cognitively challenged individuals should never operate this appliance.
4. To protect against electrical shock do not immerse cord, plug or any part of this unit in water or other liquids.
5. Unplug from outlet when not in use.
6. DO NOT operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or if the appliance has been damaged in any manner. Return the appliance to the nearest repair shop for examination, repair or adjustment. Do not attempt to replace or splice a damaged cord.
7. The manufacturer does not recommend the use of accessory attachments. DO NOT use outdoors.
8. DO NOT let cord hang over edge of table or counter, or touch hot surfaces.
9. DO NOT place on or near a hot gas or electric burner, or in a heated oven.
10. Always attach plug to appliance first, then plug cord into the wall outlet (for appliances with detachable cords). To disconnect, turn any control to the off position, then remove plug from wall outlet.
11. This is not suitable for use In the education domain, video playback Is the main function. Not recommended for Word or spreadsheet.
12. CAUTION!: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
13. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
14. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
15. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
16. Reorient or relocate the receiving antenna.
17. Increase the separation between the equipment and receiver.
18. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
19. Consult the dealer or an experienced radio/TV technician for help.
20. FCC Radiation Exposure Statement
21. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
22. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
23. For pluggable equipment, the socket-outlet shall be easily ACCESSIBLE

Knowing your projector and remote control

Note: Do not mix old and new batteries and Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries.

Parts and Functions of Projector

Getting started

1. Connect the projector with power cord, then plug the power cord into AC connector. When the indicator light stops flashing, projector is under standby status.

2. Connect your device to the chosen input port in the back of the projector.
   

3. Press the power button on remote control or projector.
   Press the Home button on the remote control and choose the input source of your connected device.
   

4. Adjust the keystone distortion.
   

5. Adjust the focus.
   

Production Connection

1. Multimedia input
   Insert the USB into USB1 as showed in picture below.
   
   Select MOVIE, MUSIC, PHOTO and TEXT icon to playback the media files in USB

2. VGA Input
   Choose VGA input, and connect projector with computer
   

3. AV Input
   Choose AV input, and connect projector with AV signal
   

4. HDMI Input
   Choose HDMI input, and connect projector with HDMI signal
   

5. Audio Output
   Connect with 3.5mm earphone o similar audio devices.
   

Projector settings

Open the video page and select the MENU icon on the projector. Press the left and right arrows on the projector panel or remote control, choose between different options and press “OK” to select from the adjustments of the submenu items.

Connecting your mobile device

Press SOURCE button and switch to Screen Mirroring source.
Press OK button to switch Android Display and iOS display.

Android Display
Open the Android device. Make sure WiFi is turned on.
Select the Android device’s wireless display or multiscreen function to activate screen mirroring. This is often called “Smart View.” Select “Projector XXXXXX” to connect to the projector. After a few seconds the Android device’s screen will be displayed by the projector.

iOS Display

iOS Display via WiFi:

1. Open the iOS device. Make sure WiFi is turned on.

2. Select “Projector-XXXXXX” to connect to this projector. If asked, enter password “12345678” and press “Join”.

3. Open the iOS device’s browser and enter “192.168.49.1”,

4. Select “WiFi AP”, and then select “Scan” to auto search the WiFi router SSID and then type password to connect projector to WiFi router.

5. If the WiFi router SSID is hidden, please select “Add Network” to manually input SSID and password to connect.
   

6. Connect the iOS mobile device to your home WiFi network.

7. In the iOS mobile device, pull down the control panel, select “Screen Mirroring” and select “Projector-XXXXXX”, the projector will display the iOS screen.

8. 

iOS Display via USB cable:

1. Connect the iOS device to the projector USB 2 port using Apple Data Cable.
2. For the first time (after connecting to the projector device, it will connect automatically), a dialog box will pop up to ask “Trust the device?”. Click “Trust” and wait for 3-5 seconds, then the content of the iPhone or iPad will be projected to the projector screen.

Connect PC windows 10

1. Press SOURCE button and switch to Screen Mirroring source, and select “Android Display”
2. Make sure both of your projector and computer are connected to the same WiFi router.
3. Click quick key by + P/K button on the computer, and connect to the device named by “Projector-XXXXXX” to start your projection.

NOTE: Please upgrade your windows 10’s operation system to the latest version.

Projection size and distance

Technical data

Appliance description: LED projector
Model/Appliance code: H3
Power Input: 100-240V~ 50/60Hz, Max 70W
Dimensions: 12.99 x 10.83 x 10.83 Inches

Troubleshooting

Some problems may be caused by minor faults that you can fix yourself. To do so, follow the instructions in the following table. If it is still not possible to resolve the problem, contact customer service. Do not repair the device yourself.

1. Check whether the power cord is connected property.

Unable to screen mirroring|

1. Refer to the Quick Guide to make sure you are using the correct wireless connecting entrance for your device and operating system.
2. If the screen stutters or lags, the distance between your device and projector is too far The suggested distance is within 2m.
3. Make sure the device is connected to correct SSID of the projector.

Cannot focus image|

1. The best projection distance is selected to your Wi-Fi router. Go For, Setting distance is appropriate.
2. Check the lens is dean.

Remote controller cannot work|

1. Replace the batteries of remote control.
2. The best control distance is ‘3m
3. The IR is at front sidE and pack side     of projector. Try to point at it when using remote controller.

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For indoor use only, use outdoors or in other modes not covered by this manual may violate the FCC regulation and violate the user authority to use the product.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must follow the specific operating instructions for satisfying RF exposure compliance.

Disposal

Disposal of the packaging

Sort the packaging before you dispose of it. Dispose of cardboard and carton as waste paper and wrapping via the recyclable material collection service.

Disposal of the LED projector

Old appliances may not be disposed of in the household trash!

• Should the LED projector no longer be capable of being used at some point in time, dispose of it in accordance with the regulations in force in your city or state.
• Please ensure your recycling information conforms with the local regulations and EPA recommendations (www.epa.gov).

Save These Instructions
Keep the user manual for future reference.

US

DIST. & SOLD EXCLUSIVELY BY:
ALDI
BATAVIA, IL 60510

AFTER SALES SUPPORT
SERVICIO POSVENTA

US 866-235-5029
 info@customercareusa.com

DOWNLOAD RESOURCES

• BAUHN H3 LED Projector [pdf] User Manual H3, 2A5MV-H3, 2A5MVH3, H3 LED Projector, H3, LED Projector
• Read more: https://manuals.plus/bauhn/h3-led-projector-manual#ixzz7ggpXfgkM

FAQ’S

What is the difference between BAUHN H3 and other projectors?

The BAUHN H3 is the first projector that uses the latest LED technology to provide a high contrast ratio and a high brightness in a compact design. It has a brightness of 3,000 ANSI lumens, which is more than twice as bright as most LCD projectors.

How long does the LED lamp last?

The LED lamp will last for up to 20,000 hours at normal operating temperature. This means that you will not have to replace it for over ten years if you use your projector for three hours every day. If you use the projector for longer periods or at higher temperatures, the lifetime of the lamp will be shorter.

How do I know when to replace the lamp?

When your projector starts to display reduced brightness or color saturation or if you notice flickering, this indicates that it is time to replace the lamp. If you continue using your projector with a defective lamp, this may lead to permanent damage of your device.

How do I replace the lamp?

Please follow these instructions carefully in order to avoid damaging your device. First of all, turn off your projector and unplug it from its power source. Then remove all screws from the casing using a screwdriver and take off the cover carefully. You can then access the lamp compartment by removing two screws on both sides of it and lifting up one side of it slightly so that you can pull out the old lamp from its socket on top of the device. Now carefully insert your new BAUHN H3 LED Lamp into position and make sure that it clicks into place properly before replacing both sides of the casing again and reattaching all screws. Finally, turn on your projector again and let it warm up for about 30 minutes before using it again in order to extend its lifetime even further!

What are some typical applications for my new BAUHN H3 LED Projector?

You can use this device at home or in your office for presentations or movies, but also while traveling or camping outdoors as long as there is sufficient light available around you (e.g., sunlight). It is also great for watching sports events or playing games with friends!

What is the disadvantage of BAUHN LED light?

Perhaps the biggest drawback of LED light bulbs is that they emit more blue light than incandescent bulbs, which are more on the red end of the spectrum. Blue light can cause a disruption in your circadian rhythm, negatively affect your ability to fall asleep and the quality of your sleep.

How do I reset my LED projector?

Let’s select the reset tab on the bottom. Once you select it press Enter. Once you press ENTER you’re going to see reset all or reset lamp hours let’s select reset lamp hours and press ENTER.

Why is the BAUHN LED projector on my projector not working?

Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary. Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. If operating the projector at high altitude, turn on High Altitude Mode.

Why is my projector screen blank?

Press the projector’s power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver. Press the Menu button. If the projector menu is able to display, there may be a problem with the connected video source, cable connection, or port.

How do I know if I need a new projector bulb?

Once the lamp light is at about half its original luminescence, it’s time to replace it. You can continue to use the bulb until complete failure, but doing so impacts image quality. Check how many useful hours your lamp has left in the menu options of the projector.

How do I unlock my projector?

If the projector’s control panel buttons have been locked, hold the Enter or lock button on the projector’s control panel for seven seconds to unlock them. You can also use the remote control to set the Control Panel Lock setting to Off in the Settings menu.

What does a lamp timer mean in projector?

Just like any light bulb, projector bulbs have an expected operating time, called lamp life. This value is expressed in hours and represents the number of hours before the lamp is at half its original brightness.

BAUHN H3 LED Projector
www://bauhn.com.au/

References

• USA Location information - USA.com
• ALDI Grocery Stores - Quality Food. Everyday Low Prices.
• U.S. Environmental Protection Agency | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>