IDEAL AP60 PRO Air Purifier Instruction Manual

IDEAL AP60 PRO Air Purifier

Important safety instructions

Introduction: Thank you for choosing a device from IDEAL.

Intended use

• The device is used exclusively for cleaning the ambient air indoors.

•  Please read these operating instructions before starting to use the device and please follow the safety instructions.
  The operating instructions must be kept available with the device at all times.

• Read and save these instructions: to persons associated with the use of the appliance.

Important safety instructions

• Only use the device indoors.

• Only use a wall socket that supplies the correct voltage (see rating plate).

• Do not modify or repair the device.

• Do not use the device if the power cable or mains plug is damaged or if the connection at the wall socket is not stable.

• Make sure that the power cable does not get crushed while you are using the device and that it cannot be damaged in any other way. Place the cable so that no one will trip over it. Do not place the power cable under strain.

• Disconnect the plug from the wall socket for cleaning purposes, before time.

• Do not touch the plug or the device if you have wet hands.

• Keep packing material, such as plastic wrapping, away from children! (Risk of suffocation)

• Place the device at least 10 cm away from the wall.

• Keep the device away from areas subjected to draft (wind).

• Make sure that furniture, fabrics or other objects do not come in contact with the air intake/outlet or block them.

• Place the device on a stable, even surface and make sure there is

• Do not spray any insect repellent.

• Do not use in rooms where the device may come into contact with fuel vapour or metal dust.

• Do not use any volatile liquids, petroleum, kerosene, paint thinner or polishing paste to clean the device. Such liquids may damage the surface of the device.

• Do not expose the device to rain, water, moisture or high humidity, and do not set it up in a bathroom or kitchen next to a sink.

• Make sure that no foreign objects get into the outlet grilles.

• The device is not suitable for removing harmful gases (carbon monoxide, e.g. from heating appliances).

• The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.

• Children are being supervised not to play with the appliance.

• Do not block the air intake and outlet. technical parameters. Improper usage may pose a threat to life and health.

• Disconnect the mains plug prior to any cleaning or maintenance work.

• Do not use any solvents. These could damage the housing surface.

• Do not use any substances containing silicone, since this could destroy the air quality sensor.

• Do not test the effectiveness of the air quality sensor with high quantities of gas, or alcohol, since this could destroy the air quality sensor.

• Clean the textile cover with a vacuum cleaner.

• If necessary, the textile cover can also be washed by hand (please refer to the care instructions on the label).
  WARNING: Chemical Burn Hazard. Keep batteries away from children.

• This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention
  Caution

• Risk of injury due to electric shock. Always disconnect the mains plug prior to:

• Carrying out maintenance work or cleaning

• Moving the device

• Changing the filter
  Danger

• Do not use any spray cans with flammable content near to the Air Purifier

• Do not use any flammable cleaning agents.

Product features/ Included in the box

Product features

• Filter replacement indicator:
  An illuminated red replacement indicator on the air purifier indicates that the filter cartridge
  Air purification in 5 speed settings

• 3-stage air purification system:
  Pre-filter, HEPA filter coated with activated carbon

• 360° filter (Pre-filter, HEPA+ active carbon)
  Easy maintenance and replacement of the filter cartridge

Unpacking and setting up

Installation guidelines for optimum performance

• The air intake ducts on the top can be used as handles (see adjacent diagram).
• Place the device at least 10 cm away from the wall.
• Keep the device away from areas subjected to draft (wind).
• Make sure that furniture, fabrics or other objects do not come in contact with the air intake/outlet or block them.
• Place the device on a stable, even surface and make sure there is sufficient air circulation

1. Take out the power cable (1.), operating instructions (2.) and remote control (3. with self-adhesive magnetic film).
2. Remove top packaging tray. Grasp the Air Purifier by the air intake ducts and lift it out of the box.
3. Please remove and dispose the self-adhesive tape (4. Transport safety).
4. The front panel is hooked from below at two ends and is kept closed by totally 4 magnets. Open the front panel at the top, grip it firmly (5.) and then swing it downwards (6.)
5. Remove the single piece of cardboard (7. Transport safety).
6. Remove the front panel (8.)
7. Hold the filter cartridge with both hands using the recessed grips provided and turn it anti-clockwise Take out the filter cartridge and remove the protective film
8. Insert the filter cartridge with the three tabs in the notches provided and lock in position by turning clockwise
9. Hook in the front panel at the bottom then pivot upwards and press shut Connect the power cable to the device first then to the socket
   • Note: Use the original packaging to store the air purifier if you are not using it all year round Pack and store the filter cartridge airtight to protect the activated carbon

Safety information

Operating the air purifier without panels and protective covers (motor protection grille, ventilation outlet grille, door, etc.) fully and securely attached is not permitted.

Overview and description of parts

Control panel

Note: The air quality sensor (L) is recalibrated the first time you switch it on (A) and after being disconnected from the mains power supply. Once the air quality sensor has been calibrated, the air purifier always starts in automatic mode. If the filter cartridge is missing, the filter replacement (F) and air quality indicators (E) flash red alternately.

Fan speeds

• Press the on/off button (A) to switch the air purifier on or off. The air purifier runs in automatic mode
• A. In automatic mode, the fan speed (G) automatically adapts to the measured air quality.
• The worse the air quality, the higher the fan speed.
• Press the fan speed button (B) to exit automatic mode. The air purifier now runs at fan speed
• Press again to increase the fan speed to E.
• Press again to increase the fan speed too or to the turbofan speed I.
• The turbo speed setting for fast purification of the ambient air requires the air purifier to run at maximum capacity.
• This can only be selected manually.
• Timer functions Pressing the timer while the air purifier is switched on activates the “switch-off timer> after the set time, the air purifier switches off: Switch the air purifier on (on/off button A). Press the timer button (C) to activate the timer.
• Press repeatedly to increase the timer time: 1 (h) >4-. Each number lights up in turn. Press the timer button again (no number lights up) to disable the timer function.
• The timer indicator counts the respective time with (Countdown).
• The remaining time is displayed. Pressing the timer button while the air purifier is switched off activates the “switch-on timer” after the set time, the air purifier switches on.

Quiet function

The Quiet button (D) is provided for particularly low-noise, unobtrusive operation (e.g. bedrooms). Press the Quiet button (D) to switch the fan speed (G) to its lowest capacity and switch off all indicators. Only the Quiet indicator (1) is dimly lit.

Air quality indicator (E)

• The air quality is displayed in 3 colours:
• Green: good air quality
• Yellow: average air quality
• Red: poor air quality

Filter replacement indicator (F)
An illuminated red” E” on the control panel indicates that the filter needs replacing.

• The life expectancy of the filter is approx.
• 1 year (depending on operation and purification activities).
• If odours are no longer being filtered out, or if the filter produces unpleasant odours, then the filter cartridge needs to be replaced sooner.
• Only use the original IDEAL filter cartridge. The device will only function with an original IDEAL filter cartridge.

Daylight sensor (J)

• The display brightness is automatically adjusted to the ambient light.

IR receiver (K)

• Receives the signals from the remote control.

Air quality sensor (L)

Remote control

Battery usage

• Always use 3V lithium batteries CR2025 for the remote control.
• Incorrect battery usage may result in leakage of battery fluid and/or damage.
• If the remote control is not going to be used for a long time, please remove the battery.

Unsuitable location

• Make sure that no objects or furnishings are situated between the remote control and the air purifier.
• The air purifier should not be placed in direct sunlight.
• This could impair the infrared senso.
• Locations where fluorescent tubes are flickering because they are defective or old.
• Do not store the remote control in direct sunlight and/or close to radiators/heaters.

When using for the first time

• The remote control has a pre-installed lithium battery CR2025. Remove the protective flap to activate the remote control battery.

How to use it correctly

• Point the remote control at the air purifier (IR receiver K).
• Open the battery compartment by pressing (A) and pulling out (B) at the same time. Take out the flat battery.
• Insert a new battery into the battery compartment, making sure the polarity is correct (+ / -).
• Always use 3V lithium batteries CR2025. • Slide the battery compartment back into its seating (C).

The remote control comes with a self-adhesive magnetic film (D). If required, this can be stuck on the back of the remote control. With the magnetic film stuck on it, the remote control can easily be attached to any ferromagnetic surface (e.g. on the back of the air purifier).

Important information about the batteries and how to dispose of them

• Batteries must NOT be disposed of with household waste. As the user, you are legally obligated to return used batteries for proper disposal.
• You can hand in your batteries at public collection points in your community or wherever the same type of battery is sold.
• It is very important that you make sure that the polarity of the batteries is correct.
• Batteries that are leaking fluid are dangerous. Only touch these with suitable gloves. Keep batteries out of the reach of children. period of time.
• The cells shall be disposed of properly, including keeping them away from children.
• Even used cells may cause injury

Function

• N: Select the required fan speed.
• O: Switches the air purifier to automatic mode A.
• P: Switches the air purifier on/off O. Switches the air purifier to Quiet mode
• R: Select the required timer time 9.
• S: Press the locking button to lock the buttons on the control panel (air purifier).
  Press the locking button again to unlock. The lock can also be removed by disconnecting the air purifier from the mains or by pressing and holding down the on/off button (A) on the device.

Note: When you operate the remote control, the air quality indicator (E) lights up for approx. 1 second in acknowledgement. If you operate a button on the control panel (air purifier) while the locking function is activated, the air quality indicator (E) lights up briefly in red.

Changing the filter

• Filter replacement (e.g. in accordance with the filter replacement indicator F, see page 34)
• Note: Only original IDEAL filter cartridges (order from www.ideal.de) may be used. No tools are required to replace the filter cartridge.

CAUTION: Disconnect the mains plug!

• The front panel is hooked in at the bottom in two places and kept shut with 4 magnets. Open the front panel from the top and hold (1.), pivot downwards (2.) and take off (3.)
• Hold the spent filter cartridge with both hands using the recessed grips provided and turn it anti-clockwise (4.). Remove the filter cartridge (5.). Remove the protective film from the new filter cartridge (6.)
• Insert the new filter cartridge with the three tabs in the notches provided and lock in position by turning clockwise(7).
• Hook in the front panel at the bottom first (8.), then pivot upwards and press shut (9.). Connect the power cable to the device first (10.), then to the socket (11.)

Note: The air purifier automatically detects that a new IDEAL filter cartridge has been inserted and automatically resets the filter replacement indicator. IDEAL filter cartridge Order no. 8741 099

App Control/ WLAN App

• Control Your purifier can additionally be controlled by the “IDEALAIRPRO” App via your smartphone/tablet (OS’Android).

Enabling/disabling WLAN

The air purifier is connected to the power supply and switched off.

• Press and hold down the Quiet button (D) until the air quality indicator (E) flashes

  • The WLAN is enabled
    when the air quality indicator (E) flashes blue

  • The WLAN is disabled
    when the air quality indicator (E) flashes white.

Resetting the WLAN

• The air purifier is disconnected from the power supply. Press and hold down the Quiet button (D), plug in the power cable and continue to hold down the Quiet button (D) until the air quality indicator (E) flashes pink The WLAN is reset to factory settings.
• Note: To ensure a stable WLAN connection, a minimum distance of 1 m between the air purifier and smartphone/tablet should be maintained during setup (connection setup).

Cleaning and maintenance/ Accessories

Cleaning and Maintenance

CAUTION: Disconnect the mains plug prior to any cleaning or maintenance work!

• Replace the filter cartridge as soon as the filter replacement indicator (F, page 34) lights up.
• The average life expectancy of the filter is approx. 1 year (depending on operation and purification activities).
• Clean the air purifier housing with a lint-free cloth moistened with soapy water.
• Clean the control panel with a dry, lint-free cloth.
• Clean the openings for the air quality sensor (L) and the dust sensor (M page 32) with a vacuum cleaner. Clean the air intake ducts (page 31) and the interior of the air purifier with a vacuum cleaner.
• Clean the filter cartridge’s pre-filter with a vacuum cleaner. To do this, remove the filter cartridge (“Changing the filter” page 38).
• Do not use any solvents. These could damage the housing surface, the control panel and the air quality sensor.
• Protect the air purifier from water. Do not use any substances containing silicone, since this could destroy the air quality sensor.
• Do not test the effectiveness of the air quality sensor with high quantities of gas, or alcohol, since this could destroy the air quality sensor.

Accessories

You can source accessories via your dealer or at www.ideal.de

Troubleshooting

Did none of the specified solutions help you with your problem?

Technical data contact:** Service www.krug-priester.com service@krug-priester.com

IDEAL AP60 PRO

IDEAL AP80 PRO:

The company Krug + Priester has the

• The quality management system according to
  DIN EN ISO 9001:2015

• Environmental management system
  according to DIN EN ISO 14001:2015

• The energy management system according to
  DIN EN ISO 50001:2018

Terms of warranty

IDEAL provides a warranty for this device from the date of purchase. The terms of the warranty are defined by our local representative.

• If a material or design defect ocCurs during the warranty period, IDEAL shall repair or replace the device, or repay the purchase price, at its discretion.
• The warranty will only be honoured if sufficient evidence is submitted, e.g. sales receipt and the claim under warranty is made within the warranty period.
• The warranty does not cover wearing parts or parts that need to be replaced regularly.
• The warranty shall be void if the device is not set up, adjusted and cleaned/maintained correctly (in accordance with the operating instructions).
• The warranty shall be void if the device is connected to a power supply that does not comply with the rating plate data.

Storage

We recommend storing the air purifier in its original packaging in a cool, dry place. Pack and store the rilter cartridge airtight to protect the activated carbon.

Spare parts and accessories

You can source spare parts via your dealer or at www.ideal.de. Only use the manufacturer’s original parts.

Repairs

must only be carried out by qualified experts or the customer service department. This also applies if you have a defective power cable. Any attempt by untrained persons to perform repairs may pose a considerable risk to the user and invalidate the warranty.

Disposal

This device must not be disposed of with household waste! Please hand this device in at the collection points provided! Collecting and recycling electrical and electronic waste Conserves valuable resources! The packaging material can be recycled. Dispose of the packaging in an environmentally friendly manner and take it to the recyclable waste collection. Thanks!

Documents / Resources

| IDEAL AP60 PRO Air Purifier [pdf] Instruction Manual
8741119, 2A3QI-8741119, 2A3QI8741119, AP60 PRO Air Purifier, AP60 PRO, AP80 PRO, Air Purifier
---|---
| IDEAL AP60 Pro Air Purifier [pdf] Instruction Manual
AP60 Pro, AP80 Pro, AP60 Pro Air Purifier, Air Purifier

References

• Fresh Nuts, Southern Candy, Baked Goods, and More | Priester's Pecans
• IDEAL: Aktenvernichter, Schneidemaschinen und Luftreiniger | IDEAL
• IDEAL: Aktenvernichter, Schneidemaschinen und Luftreiniger | IDEAL
• Willkommen bei Krug + Priester I krug-priester.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>