Vesternet 8 Button Zigbee Wall Controller User Guide
- June 3, 2024
- Vesternet
Table of Contents
- Function introduction
- Product Data
- Safety & Warnings
- Operation
- Removed from a Zig bee Network through Coordinator or Hub Interface
- Factory Reset Manually
- Remove a Touch link Paired ZigBee Lighting Device
- Factory Reset a Lighting Device (Touch Reset)
- Find and Bind a Zigbee Lighting Device
- Find and Unbind a Zig bee Lighting Device
- Clear All Find and Bind Mode Paired Lighting Devices
- Setup a Network & Add Devices to the Network (No Coordinator or Hub
- OTA
- How to Check Whether the Remote Belongs to a Network or not
- Battery Power Monitor Function
- Installation
- Mounting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Vesternet 8 Button Zigbee Wall Controller User Guide
Important: Read All Instructions Prior to Installation
Function introduction
Front side
Back side
Product Data
Operation Frequency | 2.4GHz |
---|---|
Transmission Range (free field) | 30m |
Power Supply | 3VDC (CR2450) |
Operating temperature | 0-40°C |
Relative humidity | 8% to 80% |
Dimming Range | 0.1%-100% |
Dimensions | 71.2×71.2×13.6mm |
Protection Type | IP20 |
- ZigBee dim remote based on ZigBee 3.0
- Enables to control both single color lighting devices
- Battery powered remote with low power consumption
- Enables to pair ZigBee lighting devices via touchlink commissioning without coordinator
- Supports find and bind mode to pair with ZigBee lighting devices
- Supports 4 groups for binding max. 30 lighting devices
- 2.4 GHz global operation
- Transmission range up to 30m
- Compatible with universal ZigBee Gateway products
- Compatible with universal single color ZigBee lighting devices
ZigBee CIusters Supported by This Remote Are As Follows:
Input clusters:
- Basic
- Power Configuration
- Identify
- Diagnostics
Output clusters:
- Identify
- Group
- On/off
- Level control
- Ota
Safety & Warnings
- This device contains a button lithium battery that shall be stored and disposed properly.
- DO NOT expose the device to moisture.
- Do not ingest battery, Chemical Burn Hazard
- This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any pa rt of the body, seek immediate medical attention.
Quick Start (Simplified operation compared to standard operations in the
part “Operation”)
- Touchlink + Add Group 1: Press and hold down both keys for 3 seconds to start touchlink and link light device to group 1.
- Touchlink + Add Group 2: Press and hold down both keys for 3 seconds to start touchlink and link light device to group 2.
- Touchlink + Add Group 3: Press and hold down both keys for 3 seconds to start touchlink and link Iight device to group 3.
- Touchlink + Add Group 4: Press and hold down both keys for 3 seconds to start touchlink and link light device to group 4.
- Factory reset: click both buttons 3 times to reset the remote (the remote should already be paired to a gateway).
Network pairing mode: click both buttons 3 times to set the remote into network pairing mode (the remote should not belong to any gateway network).
Operation
- This ZigBee Dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems. This transmitter sends wireless radio signals that are used to remotely control a compatible system.
- This Zig Bee remote suppo rts 4 grou ps for bin ding max. 30 fig hting devices and enab les to control sing Ie co for Zig Bee fighting devices.
- Zigbee Network Pairing through Coordinator or Hub (Added to a Zig bee Network)
Step 1: Remove the remote from previous zigbee network if it has already
been added to it, otherwise pairing will fail. Please refer to the part
“Factory Reset Manually”.
Step 2: From your zigbee controller or hub interface, choose to add
device or accessory and enter Pairing mode as instructed by the controller.
Step 3: Press and hold down both until LED indicator turns on.
Step 4: Immediately short press to search nearby network, indicator
flashes every 1 second, 20 seconds timeout if there is no network. Indicator
will then blink 5 times quickly for successful pairing.
Note:
- After pairing successfully, the remote information will appear on the controller or hub interface.
- No remote information wiII appear on the hub interface if pairing to Philips Hue Bridge.
Touch Link to a Zigbee Lighting Device
Step 1: Set the zigbee lighting device to start Touch Link commissioning,
please refer to its manual to learn how.
Step 2: Bring the remote within 10cm of the lighting device
Step 3: Short press ON button of group 1/2/3/4 to choose a group that
you would like to pair the device to.
Step 4 : Press and hold down both until LED indicator turns on.
Step 5: Immediately short press to start Touch Link commissioning of the
remote. LED indicator flash fast for 3S, then flash 6 times slowly to indicate
successful pairing to the device and the light connected to the device will
blink twice.
Note:
- Directly Touch Link (both not added to a Zig Bee network), please first factory reset both the remote and device, each remote can link with max. 30 devices, please make sure the fi rst linked device is always powered on when touch link the remote with 2nd device and more devices.
- Touch Link after both added to a Zig Bee network, each device can link with max. 30 remotes.
- To control by both remote and hub, add both remote and device to network first then TouchL ink, after Touch Link, the device can be controlled by the linked remotes and Zigbee hub together.
Removed from a Zig bee Network through Coordinator or Hub Interface
Factory Reset Manually
Step 1: Press and hold down both until LED indicator turns on.
Step 2: Immediately short press 5 times continuously, indicator flashes 3
times quickly to indicate successful reset.
Note: All configuration parameters will be reset after the remote is reset or removed from the network.
Remove a Touch link Paired ZigBee Lighting Device
Step 1: Set the Touch link paired zig bee device to start Touch Link
commissioning, please refer to its manual to learn how.
Step 2: Bring the remote within 10 cm of the lighting device.
Step 3: Short press ON button of group 1/2/3/4 to choose a group.
Step 4: Press and hold down both until LED indicator turns on.
Step 5: Immediately short press twice to start Touch Link removing of the
remote. LED Indicators .
Factory Reset a Lighting Device (Touch Reset)
Note: the device shall be added to a network, the remote added to the
same one or not added to any network.
Step 1: Set the zigbee device to start Touch Link commissioning refer to
its manual.
Step 2: Bring the remote within 10cm of the lighting device
Step 3: Press and hold down both until LED indicator turns on.
Step 4: Immediately short press 5 times to start Touch Reset of the
remote. LED indicator flashes fast for 3S, then flash 3 times slowly to
indicate successful reset.
Find and Bind a Zigbee Lighting Device
Note: Make sure the device and remote already added to the same zigbee
network.
Step 1: Start find and bind mode on the Zigbee lighting device (initiator
node) and enable it to find and bind target, refer to its manual.
Step 2: Short press button of group 1/2/3/4 to choose a group that you
would like to bind the device to.
Step 3: Press and hold down both until LED indicator turns on
Step 4: Short press to enable the remote (target node) to find and bind
initiator. LED indicator flashes 4 times for successful binding or twice if
binding fails.
Note: Each remote can bind max. 30 Lighting devices.
Find and Unbind a Zig bee Lighting Device
Step 1: Start find and bind mode on the Zig bee lighting device
(initiator node) and enable it to find and bind target, refer to its manual.
Step 2: Short press button of group 1/2/3/4 to choose the group that the
device already bound to.
Step 3: Press and hold down both.
Step 4: Short press twice to enable the remote (target node) to find and
unbind initiator. LED indicator flashes 4 times for successful unbinding or
twice if unbinding fails.
Clear All Find and Bind Mode Paired Lighting Devices
Step 1: Short press button of group 1/2/3/4 to choose the group that you
would like to unbind all devices.
Step 2: Press and hold down both until LED indicator turns on.
Step 3: Short press 5 times continuously to clear all bound Iighting
devices . LED indicator flashes 4 times for successful unbinding.
Setup a Network & Add Devices to the Network (No Coordinator or Hub
Required)
Step 1: Factory reset the remote and the lighting device, refer to their
manuals.
Step 2: Touch Link the remote and device to setup a network, refer to
their manuals.
Step 3: Press and hold down both until LED indicator turns on.
Step 4: Short press button to enable the network to discover and O add
devices, LED indicator will flash twice. 180 seconds timeout, repeat the
operation .
Step 5: Set another remote into network pairing mode and pair it to the
network, refer to its manual.
Step 6: Add more remotes to the network as you would like. < 10 cm
Step 3: Press and hold down both until LED indicator turns on.
Note: Each remote can bind max. 30 Iighting devices.
Step 7: Factory reset the Iighting devices that you would like then add
them to the network, refer to their manuals.
Step 8: Touchlink to pair the added remotes and lighting devices, refer
to their manuals. Each remote can link with max. 30 lighting devices. Each
lighting device can be linked by max. 30 remotes.
OTA
The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.
How to Check Whether the Remote Belongs to a Network or not
Short press any button, indicator blinking means the remote has already been added to a network, no blinking of indicator means the remote does not belong to any network.
Battery Power Monitor Function
The remote will report battery power vaIue to the coordinator under following situations:
- When powered on.
- When short pressing both | and O buttons of group 2 simultaneously.
- When operating the switch to send data packets (over 4 hours since last operation).
- When added to the network by a coordinator.
Installation
-
Remove battery insulator
-
Install the controller to wall(2 methods)
Mounting
The key part of this controller is an universal one, especially rotary standard switch element that can be integrated in numerous frames by different manufactures as below list:
BERKER | S1, B1, B3, B7 glass |
---|---|
GIRA | Standard 55, E2, Event, Esprit |
JUNG | A500, Aplus |
MERTEN | M-smart, M-Arc, M-PIan |
CAUTION
Risk of explosion if the battery is replaced by an incorrect type
- replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
- disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
- leaving a battery in an extremely hiph temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
- a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>